Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Prop dia.

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Europa-List
View previous topic :: View next topic  
Author Message
albertakolbmk3



Joined: 13 Jun 2009
Posts: 69
Location: Innisfail, AB

PostPosted: Wed Dec 23, 2020 3:06 am    Post subject: Prop dia. Reply with quote

Hi,
New to the list. I just purchased a Europa project and am going with a non standard engine. What is the maximum safe dia. Prop with a tricycle gear or conventional tail wheel setup?
Regards,
Tony Braun


- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List

_________________
Tony B.

Kolb MKIII C
Rotax 582
C Gearbox 3.00:1
WD 66" 3 Blade Prop
Back to top
View user's profile Send private message
Duncan McFadyean



Joined: 18 Jan 2011
Posts: 219

PostPosted: Wed Dec 23, 2020 3:45 am    Post subject: Prop dia. Reply with quote

64" is the limit in the UK for trigear. Of course that's not necessarily "safe" (liability disclaimer!).
Some (not all) conventional gear Europas have higher ground clearance than both the mono and tri, so larger prop diameters may be accepted, whilst still being compliant with CS-VLA.

DMcF.

Quote:
On 23 December 2020 at 11:05 Anthony Braun <albertaflyer(at)gmail.com> wrote:




Hi,
New to the list. I just purchased a Europa project and am going with a non standard engine. What is the maximum safe dia. Prop with a tricycle gear or conventional tail wheel setup?
Regards,
Tony Braun





- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
View user's profile Send private message
Peter jeffers



Joined: 24 Aug 2020
Posts: 20
Location: hp143hr

PostPosted: Wed Dec 23, 2020 4:03 am    Post subject: Prop dia. Reply with quote

1625mm or 64" dia.
Pete Jeffers

--


- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List

_________________
Pete
Back to top
View user's profile Send private message Send e-mail AIM Address
Peter jeffers



Joined: 24 Aug 2020
Posts: 20
Location: hp143hr

PostPosted: Wed Dec 23, 2020 6:45 am    Post subject: Prop dia. Reply with quote

Further to my previous comment ie 1625mm or 64 inches diameter, please go to
the following link for all information about props certified in the UK for
fitting to various engines on various types of Europa.
http://www.lightaircraftassociation.co.uk/engineering/NewMods/Aircraft_Type_
Files/247%20-%20EUROPA.pdf
Regards
Pete Jeffers

--


- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List

_________________
Pete
Back to top
View user's profile Send private message Send e-mail AIM Address
Peter jeffers



Joined: 24 Aug 2020
Posts: 20
Location: hp143hr

PostPosted: Wed Dec 23, 2020 6:56 am    Post subject: Prop dia. Reply with quote

--

- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List

_________________
Pete
Back to top
View user's profile Send private message Send e-mail AIM Address
DuaneFamly(at)aol.com
Guest





PostPosted: Wed Dec 23, 2020 8:55 am    Post subject: Prop dia. Reply with quote

Good morning Tony, does the engine manufacturer have any input as to which props they suggest? I used a Jabiru 3300 and they addressed the prop issue in their installation manual. Do you plan on a fixed pitch, ground adjustable, or constant speed prop? With the constant speed prop being the heaviest, have you done the W&B to make sure you stay inside the “box”? Just askin’. LOL
Mike Duane N377EA
Europa XS Conventional gear
Chandler, AZ

Sent from my iPhone

Quote:
On Dec 23, 2020, at 7:37 AM, Wladimir Kummer <wladimirkummer(at)gmail.com> wrote:

Hello Tony,

What engine is being considered? I´m building a Europa XS Long Wing and intend to use a 0200 as an engine. To accomodate a longer prop will make the thrust line 2" higher.
Best regards
Wladimir
Em qua., 23 de dez. de 2020 às 08:09, Anthony Braun <albertaflyer(at)gmail.com (albertaflyer(at)gmail.com)> escreveu:

Quote:
--> Europa-List message posted by: Anthony Braun <albertaflyer(at)gmail.com (albertaflyer(at)gmail.com)>

Hi,
New to the list. I just purchased a Europa project and am going with a non standard engine. What is the maximum safe dia. Prop with a tricycle gear or conventional tail wheel setup?
Regards,
Tony Braun
===========
pa-List" rel="noreferrer" target="_blank">http://www.matronics.com/Navigator?Europa-List
===========
FORUMS -
eferrer" target="_blank">http://forums.matronics.com
===========
WIKI -
errer" target="_blank">http://wiki.matronics.com
===========
b Site -
-Matt Dralle, List Admin.
rel="noreferrer" target="_blank">http://www.matronics.com/contribution
===========







- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
davidjoyce(at)doctors.org
Guest





PostPosted: Wed Dec 23, 2020 9:46 am    Post subject: Prop dia. Reply with quote

Tony, If it is not too late I would suggest thinking very seriously about fitting any engine other than a Rotax. The plane was designed around the Rotax, it works superbly with the Rotax and if built carefully has an excellent load carrying capacity and excellent performance with a Rotax, particularly a 912S or 914. With my 914 and a Woodcomp CS prop I can exceed VNe on the flat at MAUW from 6500 ft upwards whilst having capacity for two good sized men, full fuel and luggage. Having been around the Europa scene for a couple of decades I have seen multiple episodes of folk regretting the decision to try some other sort of engine. I wouldn't knock the O-200 in airframes designed for it but it is appreciably heavier than the 912S or 914 and it is difficult to see any sensible advantage. When I analysed all the ditchings around the UK over a 20 yr period ( a few years back), of the 49 planes that went in the water, there were none powered by any Rotax 91variants, but quite a lot of Continentals. It is after all a much older design than the Rotax. Most people building carefully and fitting a Rotax will end up with an empty weight between 820 and 880 lbs (but totals well up in the 900s are not unknown). With a MAUW of 1370 lbs this gives a total useable weight or load capacity for crew and baggage of between 550 and 480lbs (that is 250 - 218kg). Baggage capacity is 80 lbs /36kg and if you are touring you may well find you need all of that. And if you are to take a couple of average chaps of 185lbs/85kg you are clearly left making compromises which will be quite restricting if your build is on the heavy side even before you fit a heavy engine.
Best wishes, David Joyce


On 2020-12-23 11:05, Anthony Braun wrote:
Quote:
--> Europa-List message posted by: Anthony Braun <albertaflyer(at)gmail.com (albertaflyer(at)gmail.com)>Hi,New to the list. I just purchased a Europa project and am going with a non standard engine. What is the maximum safe dia. Prop with a tricycle gear or conventional tail wheel setup? http://www.matronics.com/Navigator?Europa-List - Mms.matronics.com" target="_blank" rel="noopener noreferrer">http://foru=======================.matronics.com" target="_blank" rel="noopener noreferrer">http://wikisp; - List &nb --> http://www.matronics.com/contribut===============


- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
wdaniell.longport(at)gmai
Guest





PostPosted: Wed Dec 23, 2020 10:36 am    Post subject: Prop dia. Reply with quote

David 
I thoroughly endorse David's comment.  It's hard enough to build a plane without the additional challenge of a non standard engine.  I almost went down the Subaru route and so glad I didnt - I did a thing which I almost never do...I followed advice
What MAP settings do you use on your 914 for max continuous and for cruise?
Will
 
William Daniell

LONGPORT

+1 786 878 0246
On Wed, Dec 23, 2020 at 12:49 PM <davidjoyce(at)doctors.org.uk (davidjoyce(at)doctors.org.uk)> wrote:

Quote:

Tony, If it is not too late I would suggest thinking very seriously about fitting any engine other than a Rotax. The plane was designed around the Rotax, it works superbly with the Rotax and if built carefully has an excellent load carrying capacity and excellent performance with a Rotax, particularly a 912S or 914. With my 914 and a Woodcomp CS prop I can exceed VNe on the flat at MAUW from 6500 ft upwards whilst having capacity for two good sized men, full fuel and luggage. Having been around the Europa scene for a couple of decades I have seen multiple episodes of folk regretting the decision to try some other sort of engine. I wouldn't knock the O-200 in airframes designed for it but it is appreciably heavier than  the 912S or 914 and it is difficult to see any sensible advantage. When I analysed all the ditchings around the UK over a 20 yr period ( a few years back), of the 49 planes that went in the water, there were none powered by any Rotax 91variants, but quite a lot of Continentals. It is after all a much older design than the Rotax. Most people building carefully and fitting a Rotax will end up with an empty weight between 820 and 880 lbs  (but totals well up in the 900s are not unknown). With a MAUW of 1370 lbs this gives a total  useable weight or load capacity for crew and baggage of between 550 and 480lbs (that is 250 - 218kg). Baggage capacity is 80 lbs /36kg and if you are touring you may well find you need all of that. And if you are to take a couple of average chaps of 185lbs/85kg you are clearly left making compromises which will be quite restricting if your build is on the heavy side even before you fit a heavy engine.
Best wishes, David Joyce

 

On 2020-12-23 11:05, Anthony Braun wrote:
Quote:
--> Europa-List message posted by: Anthony Braun <albertaflyer(at)gmail.com (albertaflyer(at)gmail.com)>

Hi,
New to the list. I just purchased a Europa project and am going with a non standard engine. What is the maximum safe dia. Prop with a tricycle gear or conventional tail wheel setup? http://www.matronics.com/Navigator?Europa-List            - Mms.matronics.com" target="_blank" rel="noopener noreferrer">http://foru=======================
.matronics.com" target="_blank" rel="noopener noreferrer">http://wikisp;           - List            &nb   --> http://www.matronics.com/contribut===============





- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Europa-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group