Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Landing Practices
Goto page 1, 2  Next
 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Kitfox-List
View previous topic :: View next topic  
Author Message
GENTRYLL(at)aol.com
Guest





PostPosted: Mon Oct 30, 2006 8:53 am    Post subject: Landing Practices Reply with quote

I am new at taildragging and am having a problem doing three point landings in that I am stalling out a litte too high each time and bouncing. I attribute this to being used to a 172 where I physically sit higher because of the bigger plane. Is it best to try to land with a little power like in a wheel landing then backing off the power and pulling back on the stick after the main gear is on the runway or maybe even just continue with a full wheel landing?
[quote][b]


- The Matronics Kitfox-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List
Back to top
propellerdesign(at)tele2.
Guest





PostPosted: Mon Oct 30, 2006 9:59 am    Post subject: Landing Practices Reply with quote

If you do a wheelie you decide to make a wheelie before you land, and same with a 3-point landing.

When you do a wheelie, at the moment the tire just barley touch the asphalt or grass, you pull the throttle and move the stick an inch or two forward, then keep the tail up until you have full down elevator, when the tail start to come down you firmly apply full up elevator.

On a 3-point, you let the speed bleed of, with stick slowly backward, without ballooning or touching the ground until it stall from 3 inch alt.

And keep the rudder in motion.

Jan
[quote] ---


- The Matronics Kitfox-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List
Back to top
GENTRYLL(at)aol.com
Guest





PostPosted: Mon Oct 30, 2006 10:13 am    Post subject: Landing Practices Reply with quote

It's that last 3 inches that's getting me. It ends up about two feet of fall and what seems like ten feet of bounce. Luckily she has plenty of power to get out of it.
[quote][b]


- The Matronics Kitfox-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List
Back to top
dave



Joined: 22 Sep 2006
Posts: 1382

PostPosted: Mon Oct 30, 2006 10:56 am    Post subject: Landing Practices Reply with quote

There are some take offs and Landings here http://www.cfisher.com/kitfox/
scroll down the left side near bottom
Kitfox Movie Fresh from the Trailer Park.
DOWNLOAD NOW 17 mgs.
right clik save as.........

Hope that helps


Dave


[quote] ---


- The Matronics Kitfox-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List

_________________
Realtime Kitfox movies to separate the internet chatter from the truth
http://www.youtube.com/user/kitfoxflyer
Hundreds of Kitfox Movies
Most viewed Kitfox on youtube
Most popular on youtube
Highest rated on youtube
Back to top
View user's profile Send private message Visit poster's website
wingnut



Joined: 11 Jan 2006
Posts: 356

PostPosted: Mon Oct 30, 2006 11:30 am    Post subject: Re: Landing Practices Reply with quote

I had the same problem when I transitioned to the kitfox (still bites me occasionally). I eventually remembered something my instructor told me. Rather than trying to judge where the ground is right under me, look strait ahead to the end of the runway. I'm close to the ground when the picture out the front of the window starts to look the way it does when I'm on the ground. That helped me to get more consistent but I didn't really start getting smooth landings until I'd just done a whole bunch of them. No substitute for practice.
Quote:
I am new at taildragging and am having a problem doing three point landings in that I am stalling out a litte too high each time and bouncing. I attribute this to being used to a 172 where I physically sit higher because of the bigger plane. Is it best to try to land with a little power like in a wheel landing then backing off the power and pulling back on the stick after the main gear is on the runway or maybe even just continue with a full wheel landing?


- The Matronics Kitfox-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List
Back to top
View user's profile Send private message Visit poster's website
lcfitt(at)sbcglobal.net
Guest





PostPosted: Mon Oct 30, 2006 12:45 pm    Post subject: Landing Practices Reply with quote

This sounds like me early on. My glasses were the progressive type bifocals
which give no peripheral correction at all. I had a real hard time finding
the ground. That said, it seems that if you are bouncing after the wheels
touch, you are not in a true three point. Typically when this happens, you
stall with the tail up a bit and when the mains touch, the tailwheel drops
increasing the angle of attack and you are flying again at the new angle.

You might check to see that you are full stick back in the stall and also
there have been issues about inability to get the tail down - inadequate
elevator authority. Lots of guys have taped the gap to increase elevator
authority. In short, others have had this issue and it is not necessarily
the fault of the pilot.

Lowell
---


- The Matronics Kitfox-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List
Back to top
dave



Joined: 22 Sep 2006
Posts: 1382

PostPosted: Mon Oct 30, 2006 12:55 pm    Post subject: Landing Practices Reply with quote

Lowell,

Did you see that video? Would taping my gaps help me Lowell?

Also a good technique is same as glassy water landing........ slow decent
and fly to ground
Dave
---


- The Matronics Kitfox-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List

_________________
Realtime Kitfox movies to separate the internet chatter from the truth
http://www.youtube.com/user/kitfoxflyer
Hundreds of Kitfox Movies
Most viewed Kitfox on youtube
Most popular on youtube
Highest rated on youtube
Back to top
View user's profile Send private message Visit poster's website
GENTRYLL(at)aol.com
Guest





PostPosted: Mon Oct 30, 2006 2:08 pm    Post subject: Landing Practices Reply with quote

I like the slow decent, fly it to the ground technique. That was about what I had decided would work best for me. I don't know what "taping my gap" means, though.
[quote][b]


- The Matronics Kitfox-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List
Back to top
Guy Buchanan



Joined: 16 Jul 2006
Posts: 1204
Location: Ramona, CA

PostPosted: Mon Oct 30, 2006 3:24 pm    Post subject: Landing Practices Reply with quote

At 08:52 AM 10/30/2006, you wrote:
Quote:
I am new at taildragging and am having a problem doing three point landings in that I am stalling out a litte too high each time and bouncing. I attribute this to being used to a 172 where I physically sit higher because of the bigger plane. Is it best to try to land with a little power like in a wheel landing then backing off the power and pulling back on the stick after the main gear is on the runway or maybe even just continue with a full wheel landing?

If you pull back on the stick after the mains are on you'll go flying again. If you do a wheel landing you push forward to plant the mains and then keep pushing forward trying to lift the tail until it touches. Then you bring the stick back full.

1. Get a copy of "Stick and Rudder" and read it.

2. Get a copy of "The Compleat Taildragger Pilot" and read it.

3. Sit in your aircraft on the taxiway and mark three points on the windscreen; two to mark the horizon and two to mark the centerline. The marks for the centerline should then defocus to four when you focus at infinity, with the centerline in the middle of the four dots. Next apply fine line tape lines dot to dot, leaving you with the horizon and a "gun sight" for centerline.

4. When you land, make sure you are looking primarily right and left and not straight ahead. It's much easier to judge height if you do so. Glance ahead to keep things straight, but you should use right and left for altitude and drift. (Most taildraggers require right and left for everything, as there is literally no view forward.)

5. Fly down the runway under power at about 5-10 over stall. Keeping everything centered fly the plane down until you just skiff a wheel. Bring it up and try to fly down the length of the runway at 1' or less altitude, slipping the aircraft as required to align with the centerline. If you bounce don't push, just add a little power, get stable, then fly back down to the runway at minimum airspeed. Try to do this without looking forward, or just glancing forward for centerline. If the air's stable, and you're feeling really skilled, bring the speed down to just above stall and float it all the way down the runway. Go around and repeat as required.

6. Practice, practice, practice!


Guy Buchanan
K-IV 1200 / 582-C / Warp / 100% done, thanks mostly to Bob Ducar. [quote][b]


- The Matronics Kitfox-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List

_________________
Guy Buchanan
Deceased K-IV 1200
A glider pilot too.
Back to top
View user's profile Send private message Send e-mail
lcfitt(at)sbcglobal.net
Guest





PostPosted: Mon Oct 30, 2006 4:04 pm    Post subject: Landing Practices Reply with quote

Missed the video Dave.

I am just reporting the experience of others on the list. I'm sure someone
will chime in regarding elevator authority. I think it can also be a result
of landing with lots of flaps. Flaps will tend to pitch the nose down and
a bit of up elevator is then needed to hold the nose up. At the touch down
point you may run out of elevator, then as before, if the mains touch first,
the tail will drop and with the increased angle of attack, you are flying
again.

Lowell
---


- The Matronics Kitfox-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List
Back to top
dave



Joined: 22 Sep 2006
Posts: 1382

PostPosted: Mon Oct 30, 2006 5:00 pm    Post subject: Landing Practices Reply with quote

Lowell,

A few videos here http://www.cfisher.com/kitfox/
bottom left is one with lot of landings . I have no Gap seals and alot or
take off and landing with flaps , do you think it needs a gap seal ? And if
so what will I gain?
Dave
Coffee break at the Trailer park Hangar

Download 4.8 meg
Kitfox Movie Fresh from the Trailer Park.
DOWNLOAD NOW 17 mgs.

right clik save as.........

---


- The Matronics Kitfox-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List

_________________
Realtime Kitfox movies to separate the internet chatter from the truth
http://www.youtube.com/user/kitfoxflyer
Hundreds of Kitfox Movies
Most viewed Kitfox on youtube
Most popular on youtube
Highest rated on youtube
Back to top
View user's profile Send private message Visit poster's website
GENTRYLL(at)AOL.COM
Guest





PostPosted: Mon Oct 30, 2006 6:19 pm    Post subject: Landing Practices Reply with quote

That video is something else. I had a lot of takeoffs and landings that looked like that but they were not planned. Maybe someday.
[quote][b]


- The Matronics Kitfox-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List
Back to top
GENTRYLL(at)aol.com
Guest





PostPosted: Mon Oct 30, 2006 6:26 pm    Post subject: Landing Practices Reply with quote

I have done a lot of reading and understand the mechanics. Your explanations on how to get the feel of things make a lot of sense. I will be sure to try them next chance I get. I had this same stalling out a little too high problem also in both a 150 taildragger and a Citabria. I was using the transitions lens also so glasses off now.
[quote][b]


- The Matronics Kitfox-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List
Back to top
smokey_bear_40220(at)yaho
Guest





PostPosted: Mon Oct 30, 2006 7:43 pm    Post subject: Landing Practices Reply with quote

Darn Guy,

That is what I was going to say, but not nearly as
well. Smile

Kurt S.

Do not archive

--- Guy Buchanan <bnn(at)nethere.com> wrote:

Quote:
At 08:52 AM 10/30/2006, you wrote:

Quote:
If you pull back on the stick after the mains are on
you'll go flying
again. If you do a wheel landing you push forward to
plant the mains and
then keep pushing forward trying to lift the tail
until it touches. Then you bring the stick back
full.

Quote:

1. Get a copy of "Stick and Rudder" and read it.

2. Get a copy of "The Compleat Taildragger Pilot"
and read it.

3. Sit in your aircraft on the taxiway and mark
three points on the
windscreen; two to mark the horizon and two to mark
the centerline. The
marks for the centerline should then defocus to four
when you focus at
infinity, with the centerline in the middle of the
four dots. Next apply
fine line tape lines dot to dot, leaving you with
the horizon and a "gun
sight" for centerline.

4. When you land, make sure you are looking
primarily right and left and
not straight ahead. It's much easier to judge height
if you do so. Glance
ahead to keep things straight, but you should use
right and left for
altitude and drift. (Most taildraggers require right
and left for
everything, as there is literally no view forward.)

5. Fly down the runway under power at about 5-10
over stall. Keeping
everything centered fly the plane down until you
just skiff a wheel. Bring
it up and try to fly down the length of the runway
at 1' or less altitude,
slipping the aircraft as required to align with the
centerline. If you
bounce don't push, just add a little power, get
stable, then fly back down
to the runway at minimum airspeed. Try to do this
without looking forward,
or just glancing forward for centerline. If the
air's stable, and you're
feeling really skilled, bring the speed down to just
above stall and float
it all the way down the runway. Go around and repeat
as required.

6. Practice, practice, practice!


Guy Buchanan
K-IV 1200 / 582-C / Warp / 100% done, thanks mostly
to Bob Ducar.



Access over 1 million songs - Yahoo! Music Unlimited
(http://music.yahoo.com/unlimited)


- The Matronics Kitfox-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List
Back to top
Guy Buchanan



Joined: 16 Jul 2006
Posts: 1204
Location: Ramona, CA

PostPosted: Mon Oct 30, 2006 8:18 pm    Post subject: Landing Practices Reply with quote

At 04:03 PM 10/30/2006, you wrote:
Quote:
I am just reporting the experience of others on the list. I'm sure someone
will chime in regarding elevator authority. I think it can also be a result
of landing with lots of flaps. Flaps will tend to pitch the nose down and
a bit of up elevator is then needed to hold the nose up.

My IV ran out of authority with full flaps until I sealed the elevator gap
with clear tape. It will go all the way to stall now, power on or off. (My
CG is about 14.7" and I have my HS as high as it will go.)
Guy Buchanan
K-IV 1200 / 582-C / Warp / 100% done, thanks mostly to Bob Ducar.


- The Matronics Kitfox-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List

_________________
Guy Buchanan
Deceased K-IV 1200
A glider pilot too.
Back to top
View user's profile Send private message Send e-mail
Guy Buchanan



Joined: 16 Jul 2006
Posts: 1204
Location: Ramona, CA

PostPosted: Mon Oct 30, 2006 8:18 pm    Post subject: Landing Practices Reply with quote

At 07:43 PM 10/30/2006, you wrote:
Quote:
Darn Guy,

That is what I was going to say, but not nearly as
well.

Your too kind. :-[
Guy


- The Matronics Kitfox-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List

_________________
Guy Buchanan
Deceased K-IV 1200
A glider pilot too.
Back to top
View user's profile Send private message Send e-mail
Guy Buchanan



Joined: 16 Jul 2006
Posts: 1204
Location: Ramona, CA

PostPosted: Mon Oct 30, 2006 8:18 pm    Post subject: Landing Practices Reply with quote

At 07:43 PM 10/30/2006, you wrote:
Quote:
Darn Guy,

That is what I was going to say, but not nearly as
well.

Oops. You're too kind. :-[

(Man I hate it when I do that. And in public, too.)
Guy Buchanan
K-IV 1200 / 582-C / Warp / 100% done, thanks mostly to Bob Ducar.

Do not archive


- The Matronics Kitfox-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List

_________________
Guy Buchanan
Deceased K-IV 1200
A glider pilot too.
Back to top
View user's profile Send private message Send e-mail
lcfitt(at)sbcglobal.net
Guest





PostPosted: Mon Oct 30, 2006 8:31 pm    Post subject: Landing Practices Reply with quote

I guess the best answer to your question. If it aint broke, don't fix it.
Gap seals have helped others that have had difficulty getting the tail down
for full stall landings.

Lowell
do not archive
---


- The Matronics Kitfox-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List
Back to top
smokey_bear_40220(at)yaho
Guest





PostPosted: Mon Oct 30, 2006 9:29 pm    Post subject: Landing Practices Reply with quote

Heck, I only mess up in public. Like my best landings
no one ever sees. But the day I got a crowd.... I hit
that little dip in the grass runway squarely and
bounced 7 times. (Never over a foot high, but bounce,
bounce, bounce...)

Or the time I tried to do the 1/2 flaps landing on
pavement and dump the flaps to make it stick trick.
Yanked up instead of pushing down on the handle.
Straight up 10 feet, hover? Then a nice recovery
while the next plane could hardly talk for laughing
over the radio.

Forgiven, but not forgotten Guy

Kurt S.

--- Guy Buchanan <bnn(at)nethere.com> wrote:

......
Quote:
(Man I hate it when I do that. And in public, too.)

Quote:
Guy Buchanan
K-IV 1200 / 582-C / Warp / 100% done, thanks mostly
to Bob Ducar.

Do not archive



Get your email and see which of your friends are online - Right on the New Yahoo.com
(http://www.yahoo.com/preview)


- The Matronics Kitfox-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List
Back to top
janderson412(at)hotmail.c
Guest





PostPosted: Mon Oct 30, 2006 11:51 pm    Post subject: Landing Practices Reply with quote

My old instructor (ex WW2 Spitfire pilot) said always look straight ahead at
the end of the runway..Never look out the side in case she bolts on you.
When you see the side markers or side if the stip at shoulder height gently
out your perifial, pull back. Done me fine for many years/hours. And I wear
progressives...~j~


You wrote 30 Oct 2006 15:12:40 -0800
4. When you land, make sure you are looking primarily right and left and not
straight ahead. It's much easier to judge height if you do so. Glance ahead
to keep things straight, but you should use right and left for altitude and
drift. (Most taildraggers require right and left for everything, as there is
literally no view forward.)

5. Fly down the runway under power at about 5-10 over stall. Keeping
everything centered fly the plane down until you just skiff a wheel. Bring
it up and try to fly down the length of the runway at 1' or less altitude,
slipping the aircraft as required to align with the centerline. If you
bounce don't push, just add a little power, get stable, then fly back down
to the runway at minimum airspeed. Try to do this without looking forward,
or just glancing forward for centerline. If the air's stable, and you're
feeling really skilled, bring the speed down to just above stall and float
it all the way down the runway. Go around and repeat as required.

6. Practice, practice, practice!
Guy Buchanan
K-IV 1200 / 582-C / Warp / 100% done, thanks mostly to Bob Ducar.

_________________________________________________________________
Read the latest Hollywood gossip (at) http://xtramsn.co.nz/entertainment


- The Matronics Kitfox-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Kitfox-List All times are GMT - 8 Hours
Goto page 1, 2  Next
Page 1 of 2

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group