Matronics Email Lists :: View topic

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

LRI Probe location

Matronics Email Lists Forum Index -> Zenith-List

View previous topic :: View next topic

Author Message

jean-paul.roy4(at)tlb.sym
Guest

Posted: Sat Nov 11, 2006 5:19 am Post subject: LRI Probe location

Good day listers, I'm actually building my wings  (both at the same time since I have 2 tables).

  

 As I am looking forward to install a LRI (Lift  Reserve Indicator) on my 701, I wondered if it would be indicated to prepare  ahead of time for the installation of the probe (cutting the opening for the  probe and installing the vinyl tubing inside the wing before  skinning).

  

 Now my question; Where  exactly do I cut the  opening for the probe ? ie beside wich rib and how far from the leading edge ?  How big of an opening ?

  

 Thanks kindly for any infos.

  

 Jean-Paul Roy

 Angliers, Qc.

 working on wing skeleton

   [quote][b]

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

p.mulwitz(at)worldnet.att
Guest

Posted: Sat Nov 11, 2006 6:00 am Post subject: LRI Probe location

Hi Jean-Paul,



 I mounted mine in pretty much the same place as the pitot-static probe except on the other wing.  I mounted both of them on "Inspection plates"  to prevent damage while moving the wing around before final use.



 I don't remember exactly where on the chord the probe was mounted.  I think I remember some direction on this question on the LRI drawings.



 Good luck,



 Paul

 XL fuselage



 At 05:18 AM 11/11/2006, you wrote:

  	  Quote: 	
		  Good day listers, I'm actually building my wings (both at the same time since I have 2 tables).

  

 As I am looking forward to install a LRI (Lift Reserve Indicator) on my 701, I wondered if it would be indicated to prepare ahead of time for the installation of the probe (cutting the opening for the probe and installing the vinyl tubing inside the wing before skinning).

  

 Now my question; Where  exactly do I cut the opening for the probe ? ie beside wich rib and how far from the leading edge ? How big of an opening ?

  

 Thanks kindly for any infos.

  

 Jean-Paul Roy

 Angliers, Qc.

 working on wing skeleton

 	
 

 ---------------------------------------------

     [quote][b]

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

jean-paul.roy4(at)tlb.sym
Guest

Posted: Sat Nov 11, 2006 10:27 am Post subject: LRI Probe location

Thanks Paul, that gives me a good idea. I was going  to install them on ''plates'' as well.

  

 Regards 

  

 J.P. 

 do not archive

 [quote]   ---

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

challgren(at)mac.com
Guest

Posted: Sat Nov 25, 2006 8:41 am Post subject: LRI Probe location

Jean-Paul:

I put my LRI in the left wing tip in line with the lightening holes.  The inspection plate to be installed will allow access to both the LRI and the wing tip light.



The placement was suggested by the Owner of LRI.  He indicated it could go any where there would not be disturbed ahead of it.



Stan



 

On Nov 11, 2006, at 6:18 AM, Jean-Paul Roy wrote:

 	  Quote: 	
		  Good day listers, I'm actually building my wings (both at the same time since I have 2 tables).

 

As I am looking forward to install a LRI (Lift Reserve Indicator) on my 701, I wondered if it would be indicated to prepare ahead of time for the installation of the probe (cutting the opening for the probe and installing the vinyl tubing inside the wing before skinning).

 

Now my question; Where  exactly do I cut the opening for the probe ? ie beside wich rib and how far from the leading edge ? How big of an opening ?

 

Thanks kindly for any infos.

 

Jean-Paul Roy

Angliers, Qc.

working on wing skeleton

 	  Quote: 	
		        -- Please Support Your Lists          (And Get Some AWESOME FREE  November is the Annual List Fund Raiser.  Click class="Apple-converted-space"> the Contribution link below to  this year's Terrific class="Apple-converted-space">       * AeroElectric www.aeroelectric.com     * The Builder's Bookstore www.buildersbooks.com   * Aeroware Enterprises www.kitlog.com     * HomebuiltHELP www.homebuilthelp.com   --> http://www.matronics.com/contribution   Thank you for your generous class="Apple-converted-space">                                    - The Zenith-List Email Forum class="Apple-converted-space"> --> http://www.matronics.com/Navigator?Zenith-List

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

Display posts from previous:

	Matronics Email Lists Forum Index -> Zenith-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum