Matronics Email Lists :: View topic

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

Tail wheel strut

Matronics Email Lists Forum Index -> Kolb-List

View previous topic :: View next topic

Author Message

jindoguy(at)gmail.com
Guest

Posted: Thu Dec 28, 2006 8:57 am Post subject: Tail wheel strut

Sorry for the delay, I was wrestling hay rolls for my buddy and didn't get around to the photography until this morning.

It was a good thing to take a look at the strut since I was once again reminded that I haven't gotten around to painting it, yet. One of those, I want to fly right now, I'll do it up proper this winter items. And now it's winter. Anyway. 

The tubing size for the outer sleeve is 3/4" X .058, the inner is 5/8" X .065. Frankly, it's a bit heavier than I would like and I'll probably go back to aluminum when I do take it off. It is stout, though, and won't bend, at least so far, under the worst "arrival" loads.  



Rick

-- 

Rick Girard

"Ya'll drop on in"

takes on a whole new meaning

when you live at the airport.

- The Matronics Kolb-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List

Tail_wheel_strut.jpg

Description:

Filesize:

61.92 KB

Viewed:

288 Time(s)

jim

Joined: 03 Nov 2006
Posts: 107
Location: N. Idaho

Posted: Thu Dec 28, 2006 9:21 am Post subject: Tail wheel strut

Rick, is that a fully castering tailwheel in the photo?  The TW on my

Firefly does not caster.  If yours does caster, what is it and where can I

get one?



Thanks,

Jim



 	  Quote: 	
		   Sorry for the delay, I was wrestling hay rolls for my buddy and didn't get

 around to the photography until this morning.

- The Matronics Kolb-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List

_________________
Jim
N. Idaho

John Hauck

Joined: 09 Jan 2006
Posts: 4639
Location: Titus, Alabama (hauck's holler)

Posted: Thu Dec 28, 2006 9:29 am Post subject: Tail wheel strut

Hi Gang:



Couple things about tail wheel struts.



1-For my own purposes, I find the struts about twice as long as 

necessary.  The long strut also agrevates the problem with bending, 

permanently.



2-I use 4130 tail wheel strut.  However, I have it heat treated to 48 

RC, which turns it into a spring.  Normalized 4130 is very stiff, and 

if it bends, it stays bent.



john h

mkIII

- The Matronics Kolb-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List

_________________
John Hauck
MKIII/912ULS
hauck's holler
Titus, Alabama

planecrazzzy
Guest

Posted: Thu Dec 28, 2006 11:48 am Post subject: Re: Tail wheel strut

Hi Rick,

           I notice you have the springs like the prints say....



 Alot of us have changed them to the screen door type set up...



  Mine are home made , others have bought theirs...



 Here's a picture of mine , ( made with TIG welding rod )

.

.

Gotta Fly...

Mike in MN

- The Matronics Kolb-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List

Tailwheel Compression Springs 001.jpg

Description:

Filesize:

57.26 KB

Viewed:

256 Time(s)

jindoguy(at)gmail.com
Guest

Posted: Thu Dec 28, 2006 1:11 pm Post subject: Tail wheel strut

Jim, I have the 6" full swivel from Aircraft Spruce. Travis has the 4" version, and may have the 6", too, at TNK.



Rick



On 12/28/06, Jim Dunn  <jim(at)tru-cast.com (jim(at)tru-cast.com)> wrote: 	  Quote: 	
		  --> Kolb-List message posted by: "Jim Dunn" < jim(at)tru-cast.com (jim(at)tru-cast.com)>



Rick, is that a fully castering tailwheel in the photo?  The TW on my

Firefly does not caster.  If yours does caster, what is it and where can I

get one? 



	


-- 

Rick Girard

"Ya'll drop on in"

takes on a whole new meaning

when you live at the airport.  [quote][b]

- The Matronics Kolb-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List

jim

Joined: 03 Nov 2006
Posts: 107
Location: N. Idaho

Posted: Thu Dec 28, 2006 1:36 pm Post subject: Tail wheel strut

Thanks.  At Spruce I assume it's the one for 5/8" tubing and 10 degrees?



Thanks,

Jim



 	  Quote: 	
		   Jim, I have the 6" full swivel from Aircraft Spruce. Travis has the 4"

 version, and may have the 6", too, at TNK.



 Rick



 On 12/28/06, Jim Dunn <jim(at)tru-cast.com> wrote:

>

> 

>

> Rick, is that a fully castering tailwheel in the photo?  The TW on my

> Firefly does not caster.  If yours does caster, what is it and where can

> I

> get one?

>

> Thanks,

> Jim

>

> > Sorry for the delay, I was wrestling hay rolls for my buddy and didn't

> get

> > around to the photography until this morning.

>

 --

 Rick Girard

 "Ya'll drop on in"

 takes on a whole new meaning

 when you live at the airport.

- The Matronics Kolb-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List

_________________
Jim
N. Idaho

jindoguy(at)gmail.com
Guest

Posted: Thu Dec 28, 2006 2:17 pm Post subject: Tail wheel strut

That's the one.



Rick



On 12/28/06, Jim Dunn <jim(at)tru-cast.com (jim(at)tru-cast.com)> wrote:[quote] --> Kolb-List message posted by: "Jim Dunn" <jim(at)tru-cast.com (jim(at)tru-cast.com)>



Thanks.  At Spruce I assume it's the one for 5/8" tubing and 10 degrees?



Thanks, 

Jim



 	  Quote: 	
		   Jim, I have the 6" full swivel from Aircraft Spruce. Travis has the 4"

 version, and may have the 6", too, at TNK.



 Rick



 On 12/28/06, Jim Dunn < jim(at)tru-cast.com (jim(at)tru-cast.com)> wrote:

>

> --> Kolb-List message posted by: "Jim Dunn" <jim(at)tru-cast.com (jim(at)tru-cast.com)>

>

> Rick, is that a fully castering tailwheel in the photo?  The TW on my 

> Firefly does not caster.  If yours does caster, what is it and where can

> I

> get one?

>

> Thanks,

> Jim

>

> > Sorry for the delay, I was wrestling hay rolls for my buddy and didn't 

> get

> > around to the photography until this morning.

>

 --

 Rick Girard

 "Ya'll drop on in" 

"Ya'll drop on in"
	


takes on a whole new meaning

when you live at the airport.  [quote][b]

- The Matronics Kolb-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List

rap(at)isp.com
Guest

Posted: Mon Jan 08, 2007 3:57 pm Post subject: Tail wheel strut

John: My tail  strut went ahead droke this weekend. I knew it would the way

it was bending.Can you go into more detail about the heat treating process?

---

- The Matronics Kolb-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List

John Hauck

Joined: 09 Jan 2006
Posts: 4639
Location: Titus, Alabama (hauck's holler)

Posted: Mon Jan 08, 2007 4:23 pm Post subject: Tail wheel strut

Can you go into more detail about the heat treating process?

Rick P:



I use 4130 heat treated to RC 48.



Think it is 3/4 X .120 wall.



You can cut the standard length in half and still have enough to do a 

good job.



Any good heating treating plant in your area can do the heat treating 

for you.



john h

mkIII

- The Matronics Kolb-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List

_________________
John Hauck
MKIII/912ULS
hauck's holler
Titus, Alabama

Display posts from previous:

	Matronics Email Lists Forum Index -> Kolb-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum