Matronics Email Lists :: View topic - Rear wing channel jigs?

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

Rear wing channel jigs?

Matronics Email Lists Forum Index -> Zenith-List

View previous topic :: View next topic

Author Message

john.marzulli(at)gmail.co
Guest

Posted: Sun Jan 14, 2007 9:23 pm Post subject: Rear wing channel jigs?

I'm working on the rear wing channels and just finished the left and right 600m pieces (7V6-2SP) .



According to the manual, you then set the jig to 380mm for the shorter piece ( 7V6-1 ) , but the length of the channel is 380mm, so there is no room for the 7V6-3 that has to be attached. 



The plans indicate that the completed piece should be 400mm from flange to flange, so I want to think that the manual meant to specify 400mm for the jig.



Can any previous builders verify that the jig should be set to 400mm instead of 380? 



Thanks,



-- 

John Marzulli

http://701Builder.blogspot.com/



"Flying a plane is no different than riding a bicycle... it's just a lot harder to put baseball cards in the spokes.  [quote][b]

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

JohnDRead(at)aol.com
Guest

Posted: Sun Jan 14, 2007 10:06 pm Post subject: Rear wing channel jigs?

Hi John:

             I  had the same problem. It is solved this way. The attachment flange to rib #4 is  made in the end of 7V6-1 prior to placing it in the fixture that locates 7V6-3.  There is a drawing of this on sheet 7-V-6 lower right corner. Hope this  helps.

  

 Regards, John Read

  [quote][b]

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

Richard C

Joined: 09 Jan 2006
Posts: 9
Location: Perth Western Australia

Posted: Sun Jan 14, 2007 10:54 pm Post subject: Rear wing channel jigs?

John

 Made mine yesterday. Set jig to 400mm,seems to  work

 Richard 

 701 work in [slow] progress.

 do not archive

 [quote]   ---

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

lane_jones(at)bellsouth.n
Guest

Posted: Mon Jan 15, 2007 7:12 pm Post subject: Rear wing channel jigs?

John, 400mm is correct. Remember to always use the  drawings as the final authority.  

 [quote]   ---

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

Display posts from previous:

	Matronics Email Lists Forum Index -> Zenith-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum