Matronics Email Lists :: View topic

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

Batteries

Matronics Email Lists Forum Index -> RV10-List

View previous topic :: View next topic

Author Message

william(at)gbta.net
Guest

Posted: Wed Feb 01, 2006 9:52 pm Post subject: Batteries

I studied the archives a bit and found that several  of you have installed dual batteries.� I cannot find any pictures of how  the mods were made.� Does anybody have pictures of their battery  mods???� I have not decided on which batteries I will use yet.� Do I  need to know this before I build the tray???

 �

 Also, this may not be the right list to post this  question, but, to those who are considering the Egg H-6 for your -10, what are  your battery thoughts/recommendations/locations???

 �

 Bill

 RV-10 Tailcone

- The Matronics RV10-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

millstees(at)ameritech.ne
Guest

Posted: Thu Feb 02, 2006 6:43 am Post subject: Batteries

I am plannning on the Subaru H-6 for my -10,  Eggenfellner recommends two Odyssey 680 batteries.� As far as location is  concerned, I have not reached that point, however since the H-6 is about 60 lbs  lighter than the Lycosaur, it would be best from a weight and balance point of  view to locate the batteries under the cowl. You can get additional information  at Eggenfellners web site http://www.eggenfellneraircraft.com/

 �

 Steve Mills

 40486

 working on wings

 [quote]   ---

- The Matronics RV10-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

bob.condrey(at)baesystems
Guest

Posted: Thu Feb 02, 2006 2:28 pm Post subject: Batteries

Here’s what I did, batteries are a pair of PC-680s.� Not a problem to mod the tray later.  

�  

�  

�        

  

From: owner-rv10-list-server(at)matronics.com [mailto:owner-rv10-list-server(at)matronics.com] On Behalf Of Bill and Tami Britton

 Sent: Wednesday, February 01, 2006 11:48 PM

 To: RV10-list(at)matronics.com

 Subject: Batteries  

  

�    

I studied the archives a bit and found that several of you have installed dual batteries.� I cannot find any pictures of how the mods were made.� Does anybody have pictures of their battery mods???� I have not decided on which batteries I will use yet.� Do I need to know this before I build the tray???  

    

�  

    

Also, this may not be the right list to post this question, but, to those who are considering the Egg H-6 for your -10, what are your battery thoughts/recommendations/locations???  

    

�  

    

Bill  

    

RV-10 Tailcone

- The Matronics RV10-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

Tray1.jpg

Description:

Filesize:

65.77 KB

Viewed:

665 Time(s)

tray5.jpg

Description:

Filesize:

86.55 KB

Viewed:

661 Time(s)

tray6.jpg

Description:

Filesize:

97.01 KB

Viewed:

683 Time(s)

pdwalter(at)bigpond.net.a
Guest

Posted: Fri Feb 03, 2006 12:23 am Post subject: Batteries

Hi Group,

 �

 As I am part way through the VS I have run into the  same problem as I have read about previously.

 Plans say to remove 1/8 inch from VS 1013, VS 1005  and VS 1006 so as not to crease VS 1001 Vertical stabilizer skin with the point  of these mentioned ribs

 �

 Now, removing 1/8 has done nothing to solve the  problem and at this point I have taken 1/4 inch off and when assembled and you  look down through top of stabilizer the ribs do not sit flush in front of skin  as I would like. It almost seems like these ribs have not be manufactured  correctly.

 �

 Can the fronts be re fabricated to change the  actual shape of the rib ?.

 �

 Thank you

 �

 �

 Paul Walter.

 �



 [quote]   ---

- The Matronics RV10-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

Display posts from previous:

	Matronics Email Lists Forum Index -> RV10-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum