Matronics Email Lists :: View topic

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

Arplast PV50 problem

Matronics Email Lists Forum Index -> Europa-List

View previous topic :: View next topic

Author Message

gholland(at)content-strea
Guest

Posted: Thu Nov 07, 2013 10:08 pm Post subject: Arplast PV50 problem

Jim Hi....It's Gerry.Where is FIZY at moment? I'm quite happy to come down and take a look if that's of use.

As you know i'm SW of Bath. If you are still at Thruxton then it's very doable.

Let me know.

Regards

Gerry





 Gerry Holland

gholland(at)content-stream.co.uk (gholland(at)content-stream.co.uk)

+44 (0)7808 402404

[img]cid:4C0DBE17-4DEB-411D-BF75-8C8AFF101B75[/img]White Ox Mead Airstrip, Bath. England

- The Matronics Europa-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List

Avatar.jpg

Description:

Filesize:

7.92 KB

Viewed:

2603 Time(s)

kennethatkinson178(at)bti
Guest

Posted: Mon Nov 11, 2013 3:11 pm Post subject: Arplast PV50 problem

Hi,

PV50 -If you find your problem is the pitch-change motor and you find a supplier then I would like to have the details so that I can buy a spare.

It is possible to fit a resistor in the pink supply wire to the motor.It is 2 ohms-10W-RS part no:252-2489.

I love the Arplast/Smart Avionics propeller/controller system.It does take time to understand and setup correctly,particularly the coarse pitch setting to allow a reasonable climb rate on a go around.

I suspect that the micro switches may also need changing in time and even could be your problem. I have fitted the recommended mechanical stops on the pitchchange screw to limit pitch runaway in case of switch  or screw failure!  

 

Cheers Ken Atkinson G-CEKV  

     

   From: Gerry Holland <gholland(at)content-stream.co.uk>

 To: europa-list(at)matronics.com 

 Sent: Friday, 8 November 2013, 6:07

 Subject: Re: Arplast PV50 problem

  

 

Jim Hi....It's Gerry.Where is FIZY at moment? I'm quite happy to come down and take a look if that's of  use.

As you know i'm SW of Bath. If you are still at Thruxton then it's very doable.

Let me know.

Regards

Gerry





 Gerry Holland

gholland(at)content-stream.co.uk (gholland(at)content-stream.co.uk)

+44 (0)7808 402404

[img]cid:1.1085407936(at)web87402.mail.ir2.yahoo.com[/img]White Ox Mead Airstrip, Bath. England

- The Matronics Europa-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List

Avatar.jpg

Description:

Filesize:

7.92 KB

Viewed:

2577 Time(s)

g-fizy

Joined: 27 May 2012
Posts: 46
Location: uk

Posted: Tue Nov 12, 2013 12:43 am Post subject: Re: Arplast PV50 problem

hi jerry ,fizy is tucked up safe and sound in westonair's hanger at thruxton ,that offer sounds good but dont put your self out theirs no rush in this weather  ,,have you still got my number ?

- The Matronics Europa-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List

gholland(at)content-strea
Guest

Posted: Sat Nov 16, 2013 9:57 am Post subject: Arplast PV50 problem

Jim Hi!

Sorry for delayed response....getting old.

Good to hear you have a good Hangar at Thruxton.

I still have you Mobile number and will try and give you a call.



One of the simple parts of the Arplast system is the way voltage is applied to motor through the hollow prop mounting.

A single thickish piano wire comes from a potentiometer and 'seats' into a brass ferrule at the moment end.

Are you sure that is positioned correctly and also clean, not corroded?

We'll have a chat and I can probably call in later next week as I have to pick up my aircraft engine from Mike Watts in Southampton after a full overhaul.

Regards

Gerry

- The Matronics Europa-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List

Display posts from previous:

	Matronics Email Lists Forum Index -> Europa-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum