Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Smoke system and ballast mounting

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Yak-List
View previous topic :: View next topic  
Author Message
airmanv2



Joined: 01 Dec 2013
Posts: 49
Location: France - Normandy

PostPosted: Tue Apr 29, 2014 10:42 pm    Post subject: Smoke system and ballast mounting Reply with quote

Hello,
We have discovered a problem which might be hazardous. The transverse frame which carries the ballast weights and the smoke tank on top is insecure and is at risk of collapse into the fuselage, threatening the control runs (cables etc) if the support gives way.
The frame was never intended to carry this much weight and has not been reinforced when the weights and smoke tank were fitted. ANY aerobatics or a heavy landing might cause loss of structural integrity in this area. I enclose a photo of broken rivets which show the weakness. We can install additional support brackets which will make this area secure .
How did you do for your system?
Best
Bruno


- The Matronics Yak-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Yak-List



Nanchang frame damage.jpg
 Description:
 Filesize:  32.37 KB
 Viewed:  2993 Time(s)

Nanchang frame damage.jpg



_________________
Fly safe
Back to top
View user's profile Send private message
airmanv2



Joined: 01 Dec 2013
Posts: 49
Location: France - Normandy

PostPosted: Tue Apr 29, 2014 10:53 pm    Post subject: Re: Smoke system and ballast mounting Reply with quote

Just missing to say that's on a CJ6 ,
picture taken by the right trapdoor behind the wing, the yellow vertical bar is to the front , the limit of the electronic compartment (most of them removed , and now luggage compartment)
The ballast is made by 2 heavy steal plaque and smoke system fitted over it.
Bruno


- The Matronics Yak-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Yak-List

_________________
Fly safe
Back to top
View user's profile Send private message
Dawg



Joined: 19 May 2013
Posts: 355

PostPosted: Wed Apr 30, 2014 7:06 am    Post subject: Smoke system and ballast mounting Reply with quote

Like I said, buy a YAK! (lol)

On Apr 30, 2014, at 0:53, "airmanv2" <bruno.blanchard2(at)gmail.com> wrote:

Quote:


Just missing to say that's on a CJ6 ,
picture taken by the right trapdoor behind the wing, the yellow vertical bar is to the front , the limit of the electronic compartment (most of them removed , and now luggage compartment)
The ballast is made by 2 heavy steal plaque and smoke system fitted over it.
Bruno

--------
Fly safe




Read this topic online here:

http://forums.matronics.com/viewtopic.php?p=422570#422570












- The Matronics Yak-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Yak-List

_________________
Dawg
Back to top
View user's profile Send private message
Harv



Joined: 01 Jul 2010
Posts: 172

PostPosted: Tue May 06, 2014 4:54 am    Post subject: Re: Smoke system and ballast mounting Reply with quote

Bruno

We removed all the defunct Chinese military radio crap from this area and from both cockpits. This lightened my a/c by something like 50kg!

I believe the way it's been done on your a/c is a quick cheap solution and would encourage the above modification which will allow you to do away with the steel ballast plates in the area you mentioned.

It's quite involved to do and will require re-weighing and ballasting.

Either way you have a problem with those loose rivets that needs fixing right NOW!

Rgs Harv


- The Matronics Yak-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Yak-List
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Yak-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group