 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
asknickp(at)yahoo.com
Guest
|
 Posted: Wed Jan 18, 2006 7:32 am Post subject: Hole Punch |
 |
|
Just curios,why cant you use an aircraft hole punch to
make the rivit holes.It seems like it would eliminate
de-burring.Forgive me if this topic has been covered
in the past.
"THIS is the golden age of aviation"
A Fellow Aviator
Nick Pace
Harpers Ferry WV
Building a 601XL #5607
Corvair Powered
{Rudder almost done}
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
|
|
| Back to top |
|
 |
cgalley(at)qcbc.org
Guest
|
| Posted: Wed Jan 18, 2006 8:05 am Post subject: Hole Punch |
|
|
Whitney-Roper makes one but you are limited to mainly edges.
Cy Galley - Chair,
AirVenture Emergency Aircraft Repair
A Service Project of Chapter 75
EAA Safety Programs Editor - TC
EAA Sport Pilot
---
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
|
|
| Back to top |
|
|
frank.hinde(at)hp.com
Guest
|
| Posted: Wed Jan 18, 2006 8:24 am Post subject: Hole Punch |
|
|
And you still need to match drill the hole to the sructure underneath
which still has to be deburred.
You really will cost yourself more time than you will save I suspect.
Frank
--
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
|
|
| Back to top |
|
|
dredmoody(at)cox.net
Guest
|
| Posted: Wed Jan 18, 2006 10:48 am Post subject: Hole Punch |
|
|
Punches leave burs too but they vcan be used in place of drilling as long as you debur.
Ed Moody II
| Quote: |
From: nick pace <asknickp(at)yahoo.com>
Date: 2006/01/18 Wed AM 10:26:28 EST
To: zenith-list(at)matronics.com
Subject: Hole Punch
Just curios,why cant you use an aircraft hole punch to
make the rivit holes.It seems like it would eliminate
de-burring.Forgive me if this topic has been covered
in the past.
"THIS is the golden age of aviation"
A Fellow Aviator
Nick Pace
Harpers Ferry WV
Building a 601XL #5607
Corvair Powered
{Rudder almost done}
|
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
|
|
| Back to top |
|
|
Kevin Bonds
Joined: 09 Jan 2006
Posts: 171
Location: Nashville, Tn
|
| Posted: Wed Jan 18, 2006 2:36 pm Post subject: Hole Punch |
|
|
I have had one for a while. I have yet to use it. It will not allow me to
punch over a flange. Therefore it has limited uses.
Kevin Bonds
Nashville TN
601XL Corvair powered; Plans building.
Empennage done; working on wings and engine.
http://home.comcast.net/~kevinbonds
do not archive DO NOT ARCHIVE
--
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
_________________
KevinBonds
Nashville, TN
Plans-building Zenith CH601XL w/Corvair Power
http://home.comcast.net/~kevinbonds |
|
| Back to top |
|
|
bretttdc(at)yahoo.com
Guest
|
| Posted: Thu Jan 19, 2006 4:19 am Post subject: Hole punch |
|
|
I have the Grizzly version. Works great! Save the
twenty dollars and go to a pawn shop to buy a cheap,
light Skill or Black and Decker 3/8 non reversing
drill instead. Get two and you will rarely have to
change the bit.
Just curios,why cant you use an aircraft hole punch to
make the rivit holes.It seems like it would eliminate
de-burring.Forgive me if this topic has been covered
in the past.
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
