Matronics Email Lists :: View topic

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

DRDT-2 Table

Matronics Email Lists Forum Index -> RV-List

View previous topic :: View next topic

Author Message

Kearney(at)shaw.ca
Guest

Posted: Tue Sep 26, 2006 6:14 am Post subject: DRDT-2 Table

Hi



In anticipation of ordering an empennage kit on Tuesday next, I have been busy getting my workspace ready. To that end I have built two regulation EAA work tables and now would like to build a table / stand for a DRDT-2 dimplier.



Does anyone have plans for such a beast so I can build the table in advance of receiving my tool order?



Many thanks



Les 



RV10 Wannabe

UFOBUCK(at)aol.com
Guest

Posted: Tue Sep 26, 2006 6:26 am Post subject: DRDT-2 Table

In a message dated 9/26/2006 9:16:50 A.M. Central Daylight Time,  Kearney(at)shaw.ca writes:

  	  Quote: 	
		  .....To    that end I have built two regulation EAA work tables ..... 	
  

 There is an EAA regulation to the size of my work benches ????

 This is getting too complicated.  %-)

 

  

  [quote][b]

Bob Collins

Joined: 11 Mar 2006
Posts: 470
Location: St. Paul, Minnesota

Posted: Tue Sep 26, 2006 6:58 am Post subject: DRDT-2 Table

Here you go



http://www.experimentalaero.com/DRDT-2%20Manual%20&%20Drawings.pdf



Bob Collins

RV Builder's Hotline

http://home.comcast.net/~rvnewsletter/

_________________
Bob Collins
St. Paul, Minn.
Letters from Flyover Country
http://rvnewsletter.blogspot.com/

lsbrv7a(at)yahoo.com
Guest

Posted: Tue Sep 26, 2006 7:06 am Post subject: DRDT-2 Table

Les, This is the table I made. The EAA tables are level with adn suppor the work.



LES KEARNEY <Kearney(at)shaw.ca> wrote:    	  Quote: 	
		    --> RV-List message posted by: LES KEARNEY 



Hi



In anticipation of ordering an empennage kit on Tuesday next, I have been busy getting my workspace ready. To that end I have built two regulation EAA work tables and now would like to build a table / stand for a DRDT-2 dimplier.



Does anyone have plans for such a beast so I can build the table in advance of receiving my tool order?



Many thanks



Les 



RV10 Wannabe

   

	




Sherman Butler

RV-7a Wings

Idaho Falls

Dec_14_05_Dimple_slide_in.JPG

Description:

Filesize:

606.5 KB

Viewed:

813 Time(s)

carlosh(at)sec-engr.com
Guest

Posted: Tue Sep 26, 2006 7:09 am Post subject: DRDT-2 Table

LES KEARNEY wrote:

 	  Quote: 	
		   



 Hi



 In anticipation of ordering an empennage kit on Tuesday next, I have been busy getting my workspace ready. To that end I have built two regulation EAA work tables and now would like to build a table / stand for a DRDT-2 dimplier.



 Does anyone have plans for such a beast so I can build the table in advance of receiving my tool order?



 Many thanks



 Les 



 RV10 Wannabe

  

   

Here you go.
	


http://www.experimentalaero.com/DRDT-2%20Manual%20&%20Drawings.pdf



Carlos RV7A N174PP "Pretty Penny"



-- 

Carlos Hernandez

Structural Engineers, LLC

2111 E. Broadway Rd. - Suite 3

Tempe, AZ 85282

Phone: 480.968.8600

Fax: 480.968.8608

www.sec-engr.com

LloydDR(at)wernerco.com
Guest

Posted: Tue Sep 26, 2006 7:13 am Post subject: DRDT-2 Table

Here is a copy of the plans you will get from Experimentalaero when you

purchase your DRDT-2

Dan

40269 (N289DT)



 



--

drdt-2_platform.pdf

Description:

Download

Filename:

drdt-2_platform.pdf

Filesize:

102.01 KB

Downloaded:

443 Time(s)

smittysrv

Joined: 10 Jan 2006
Posts: 67

Posted: Tue Sep 26, 2006 7:31 am Post subject: DRDT-2 Table

Yeah, and you have to spend a minimum of 5.25 hours in construction on the

tables, take pictures and get a DAR sign off.



(jes' kidding)



do not archive



Smitty's RV

http://SmittysRV.com 



Original Message:

-----------------

From:  UFOBUCK(at)aol.com

Date: Tue, 26 Sep 2006 10:25:19 EDT

To: rv-list(at)matronics.com

Subject: Re: Re: DRDT-2 Table

In a message dated 9/26/2006 9:16:50 A.M. Central Daylight Time,  

Kearney(at)shaw.ca writes:



....To  that end I have built two regulation EAA work tables .....

 

There is an EAA regulation to the size of my work benches ????

This is getting too complicated.  %-)



 

--------------------------------------------------------------------

mail2web - Check your email from the web at

http://mail2web.com/ .

_________________
Smittys RV-9A
SmittysRV.com

jjessen

Joined: 22 Apr 2006
Posts: 285
Location: OR

Posted: Tue Sep 26, 2006 8:39 am Post subject: DRDT-2 Table

Did you save the cutting list?  Nice job!  

  

 John Jessen

   RV-10

  

 do not archive



   From: owner-rv-list-server(at)matronics.com  [mailto:owner-rv-list-server(at)matronics.com] On Behalf Of Sherman  Butler

Sent: Tuesday, September 26, 2006 8:05 AM

To:  rv-list(at)matronics.com

Subject: Re: Re: DRDT-2  Table

 

Les, This is the table I made. The EAA tables are level with adn  suppor the work.



LES KEARNEY <Kearney(at)shaw.ca> wrote:    	  Quote: 	
		     --> RV-List message posted by: LES KEARNEY    



Hi



In anticipation of ordering an empennage    kit on Tuesday next, I have been busy getting my workspace ready. To that end    I have built two regulation EAA work tables and now would like to build a    table / stand for a DRDT-2 dimplier.



Does anyone have plans for such a    beast so I can build the table in advance of receiving my tool    order?



Many thanks



Les 



RV10 Wannabe

    

	




Sherman Butler

RV-7a Wings

Idaho  Falls 

  [quote][b]

lsbrv7a(at)yahoo.com
Guest

Posted: Tue Sep 26, 2006 5:58 pm Post subject: DRDT-2 Table

John,

  The table is 2' X 3' . I started with the EAA table dimensions and I shortened the legs the height of the DRDT-2 table and wheels combined, placed the bottom shelf on the bottom to provide a larger bearing area for the wheel frames. The sliding table is much like the table in the DRDT-2 plans. I used heavy wheels to provide ballast to the table.

   

  My son was here for the weekend, and he worked one summer in a belly landing repair shop.  He LOVED it ------- until I showed him the pneumatic squeezer.

   

  do not archive



John Jessen <jjessen(at)rcn.com> wrote:

   	  Quote: 	
		      Did you save the cutting list?  Nice job!  

    

  John Jessen

    RV-10

   

  do not archive



      



  

Les, This is the table I made. The EAA tables are level with adn suppor the work.

   	  Quote: 	
		    

Does anyone have plans for such a beast so I can build the table in advance of receiving my tool order?

Many  thanks

Les 



Sherman Butler

RV-7a Wings

Idaho Falls 

	
	




Sherman Butler

RV-7a Wings

Idaho Falls

  		Get your email and more, right on the [url=http://us.rd.yahoo.com/evt=42973/*http://www.yahoo.com/preview] new Yahoo.com[/url]   [quote][b]

dmaib@me.com

Joined: 25 Apr 2006
Posts: 455
Location: New Smyrna Beach, Florida

Posted: Tue Sep 26, 2006 7:13 pm Post subject: DRDT-2 Table

Les,



I built two of the EAA work tables and am very happy with them. I  

built the DRDT-2 table from the plans that came with the DRDT-2 and  

it is great. Here is a photo of the DRDT-2 table.



[IMG] 

http://img87.imageshack.us/img87/88/img0652jd6.th.jpg[/IMG]



Regards,

David Maib

#40559



On Sep 26, 2006, at 9:13 AM, LES KEARNEY wrote:






Hi



In anticipation of ordering an empennage kit on Tuesday next, I have  

been busy getting my workspace ready. To that end I have built two  

regulation EAA work tables and now would like to build a table /  

stand for a DRDT-2 dimplier.



Does anyone have plans for such a beast so I can build the table in  

advance of receiving my tool order?



Many thanks



Les



RV10 Wannabe

_________________
David Maib
RV-10 #40559
New Smyrna Beach, FL

william(at)gbta.net
Guest

Posted: Thu Oct 05, 2006 5:17 am Post subject: DRDT-2 Table

Les, I've got 2 of the 3' X 5' tables also.  Due to lack of space in my 

garage for another table that will be used minimally, I just slid the two 

tables together end to end and screwed the DRDT-2 to a 2 X 6, then I screwed 

the 2 X 6 on to the legs of each table (so the dimpling sets were flush with 

the table top).  Now, when I don't need it (the DRDT-2) I can either unscrew 

the dimpler form the board and leave the board on the tables (leaves me a 

gap between tables about 6-8 inches wide) or remove the board completely.  I 

know that every time I need to do some dimpling I have to mess with screwing 

either the whole setup back on or atleast the dimpler back on.  But, for no 

more often than you really use the dimpler it's not that big of a deal, 

especially if you've got a cordless drill.



CLEAR AS MUD, right???



If you would like to see some pictures let me know.



Bill Britton

---

Display posts from previous:

	Matronics Email Lists Forum Index -> RV-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum