 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
trigo(at)mail.telepac.pt
Guest
|
 Posted: Sat Dec 20, 2014 9:15 am Post subject: Holes in the Landing Gear Mounts |
 |
|
Guys
The WD-102- L & R Landing Gear Mounts have, each of them, 4 holes in the horizontal part, the ones which must be final-drilled #12 according to step 4 (on figure 4) of page 28-16 of the Manual (Section 28 : Fwd Ribs, Bhds & Bottom Skins), which doesn’t seem to be used for anything.
Does anybody know what are these 4 holes for?
I ask because I didn’t find the answer in the Manual, though I’m tempted to use those holes to install an electric connector bus for the bunch of wires which come from the Stick grip …
Regards
Carlos
Este email está livre de vÃrus e malware porque a proteção avast! Antivirus está ativa. [quote][b]
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
 |
Rocketman1988
Joined: 21 Jun 2012
Posts: 63
|
| Posted: Sat Dec 20, 2014 12:35 pm Post subject: Re: Holes in the Landing Gear Mounts |
|
|
Those holes are for the Mid Seat Rail Supports that you assembled in step 1 and 2.
There are also several threads that identify the fact that the plans do not tell you when to install these supports, only that they should be left out in order to drill and ream the gear leg mounting hole...
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
flying-nut(at)cfl.rr.com
Guest
|
| Posted: Sat Dec 20, 2014 12:56 pm Post subject: Holes in the Landing Gear Mounts |
|
|
I got so frustrated trying to use the 4 bolts/nuts to attach those
'spacers' that I created a plate with three nutplates to go on one side
of the web (that you can't see) ..... and the bolt/nut to go on the
other side of the web. Because I could.
Linn
On 12/20/2014 3:35 PM, Rocketman1988 wrote:
| Quote: |
Those holes are for the Mid Seat Rail Supports that you assembled in step 1 and 2.
There are also several threads that identify the fact that the plans do not tell you when to install these supports, only that they should be left out in order to drill and ream the gear leg mounting hole...
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=435945#435945
-----
No virus found in this message.
Checked by AVG - www.avg.com
|
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
larkrv10(at)gmail.com
Guest
|
| Posted: Sun Dec 21, 2014 6:38 pm Post subject: Holes in the Landing Gear Mounts |
|
|
Hey Linn, I had to bring in the reserves to help get those nuts/washers on (my wife and her little hands). Heading your way at New Years, so I need to come for an inspection (again) 
Â
Rick
#40956
Southampton, Ont
On Sat, Dec 20, 2014 at 3:53 PM, Linn Walters <flying-nut(at)cfl.rr.com (flying-nut(at)cfl.rr.com)> wrote:
[quote]--> RV10-List message posted by: Linn Walters <flying-nut(at)cfl.rr.com (flying-nut(at)cfl.rr.com)>
I got so frustrated trying to use the 4 bolts/nuts to attach those 'spacers' that I created a plate with three nutplates to go on one side of the web (that you can't see) ..... and the bolt/nut to go on the other side of the web. Because I could.
Linn
On 12/20/2014 3:35 PM, Rocketman1988 wrote:
| Quote: | --> RV10-List message posted by: "Rocketman1988" <Rocketman(at)etczone.com (Rocketman(at)etczone.com)>
Those holes are for the Mid Seat Rail Supports that you assembled in step 1 and 2.
There are also several threads that identify the fact that the plans do not tell you when to install these supports, only that they should be left out in order to drill and ream the gear leg mounting hole...
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=435945#435945
-----
No virus found in this message.
Checked by AVG - www.avg.com
|
====================================
br> fts!)
r> > /www.aeroelectric.com" target="_blank">www.aeroelectric.com
w.buildersbooks.com" target="_blank">www.buildersbooks.com
p.com" target="_blank">www.homebuilthelp.com
e.com" target="_blank">www.mypilotstore.com
" target="_blank">www.mrrace.com
target="_blank">http://www.matronics.com/contribution
     -Matt Dralle, List Admin.
====================================
-List" target="_blank">http://www.matronics.com/Navigator?RV10-List
====================================
FORUMS -
_blank">http://forums.matronics.com
====================================
[b]
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
flying-nut(at)cfl.rr.com
Guest
|
| Posted: Sun Dec 21, 2014 6:46 pm Post subject: Holes in the Landing Gear Mounts |
|
|
Hi Rick!
Just give me a call .....
Merry Christmas!!
Linn
On 12/21/2014 9:35 PM, Rick Lark wrote:
[quote] Hey Linn, I had to bring in the reserves to help get those nuts/washers on (my wife and her little hands). Heading your way at New Years, so I need to come for an inspection (again)Â
Â
Rick
#40956
Southampton, Ont
On Sat, Dec 20, 2014 at 3:53 PM, Linn Walters <flying-nut(at)cfl.rr.com (flying-nut(at)cfl.rr.com)> wrote:
No virus found in this message.
Checked by AVG - www.avg.com
12/21/14 [b]
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
bob88
Joined: 24 Feb 2013
Posts: 99
|
| Posted: Sun Dec 28, 2014 4:33 pm Post subject: Re: Holes in the Landing Gear Mounts |
|
|
Another problem with those holes...I can't get them to line up with the holes in the seat rail and seat bottom. The mid seat rail supports are bolted into the landing gear mount (after much frustration) but they are half a hole too far forward. Can't move them back because the rear flanges on the mid seat rail supports are right up against the landing gear mount and it would be necessary to elongate the holes in the bottom of the mid seat rail support in any case. Anyone else with this problem? Solutions?
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
