Matronics Email Lists :: View topic

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

stratux ads-b

Matronics Email Lists Forum Index -> RV10-List

View previous topic :: View next topic

Author Message

flying-nut(at)cfl.rr.com
Guest

Posted: Mon Dec 28, 2015 8:31 am Post subject: stratux ads-b

Changed the subject!!!

       

       Thanks for the links!  As I read it, the Pi GPS is only needed if       your device does not have one.  Not a problem for most folks.

       I took the receiver cases off, used a piece of credit card as a       separator and used one top half and one lower half .... and used       metal tape to keep them together.  Leave enough 'open area' for       the heat to escape.

       

       I've been in electronics all my working life and I wouldn't think       of soldering wires to the 40 pin connector.  

       You can get a short cable at Amazon http://tinyurl.com/q4kqwn2 and       cut off the male connector.

       Linn

       

       On 12/28/2015 10:27 AM, Justin Jones wrote:

     

      	  Quote: 	
		                It looks like you may not have gotten the correct software loaded       onto your SD card that is in the Raspberry PI. Take a look at the       following links to see if they can help.              

       https://github.com/ssokol/stratux/wiki/Stratux-Beginner's-Guide#options-and-enhancements

              

       http://www.pilotsofamerica.com/forum/showthread.php?t=85058&page=1                               

                      

                      

                      

                      

                      

                                        	  Quote: 	
		                   On Dec 27, 2015, at 7:07 AM, P Reid <[url=mailto:rv10flyer(at)live.com]rv10flyer(at)live.com (rv10flyer(at)live.com)[/url]>                   wrote:

                                  --> RV10-List message posted by: P Reid                   <rv10flyer(at)live.com (rv10flyer(at)live.com)>                                      Albert                   I am using stratux on iflightplanner and fltplan.go                   In both cases the config was done via choosing ADS-B                   and picking "clarity" or port 4000 if I did it                   manually on fltplanGO.                   I've done 192.168.10.1 for configs. Never see the                   screen you attached.                   No traffic on fltplanGO but visible on iflightplanner.                   Stratux works very nicely for weather updates on both.                                                          	  Quote: 	
		  On Dec 27, 2015, at                     7:34 AM, Albert <ibspud(at)roadrunner.com (ibspud(at)roadrunner.com)>                     wrote:                                          Well, this whole Stratux thing get me going so I                     bought the Pi and the 2                     radios plus cables on Amazon. Put them together,                     very easy-just plug                     together- and then downloaded the software. Got the                     disk image file for the                     micro SD card (stratux-v0.5b2-e6ad9aa830-12212015)                     from the zip file                     download. Used Win32DiskImager to copy it to the SD                     card then put the SD                     card in my Raspberry Pi computer and fired it up.                                          I was expecting it to be configured as an ADS-B                     receiver already to receive                     broadcasts and connect to my ipad with Foreflight                     but the monitor connected                     to the Raspberry Pi shows a screen that asks for                     basic configuration                     information. Some of the item seem straightforward                     but don't know what to                     answer for others. (Screenshot attached)                                          Has anyone already gone through the setup? Could use                     some help at this                     point.                                          Albert Gardner                     RV-10 N991RV                     Yuma, AZ                     <Raspberry Pi Initial Setup.jpg>                   	
                                                         http://www.matronics.com/Navigator?RV10-List                   http://www.matronics.com/contribution

- The Matronics RV10-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

Albert Gardner

Joined: 10 Jan 2006
Posts: 455
Location: Yuma, AZ

Posted: Tue Dec 29, 2015 4:42 pm Post subject: stratux ads-b

 	  Quote: 	
		  

Well, here is the finished product except for a custom case to put it all in. So far I'm just using the plastic case the Pi came with. I'm trying it out using a splitter and 1 antenna. The big black rectangular object is a battery so it will be portable. The 4 USB hubs are very close together and the radios are too large to fit in them side-by-side so you will need the short M/F USB cables to get them away from the Pi. This was by far one of the  simplest projects I've ever done and now I'm ordering a GPS to add since my ipad doesn't have one built in.

Thanks for all the help from the list. You are worth your weight in gold.

Albert Gardner

RV-10 N991RV

Yuma, AZ

 

PS: I also attached the shopping list that I was given to get me started.

- The Matronics RV10-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

Assembled_.jpg

Description:

Filesize:

11.66 KB

Viewed:

3971 Time(s)

Exploded_.jpg

Description:

Filesize:

13.47 KB

Viewed:

3971 Time(s)

Stratux_Shopping_List.docx

Description:

Download

Filename:

Stratux_Shopping_List.docx

Filesize:

17.87 KB

Downloaded:

201 Time(s)

_________________
RV-9A N872RV
RV-10 N991RV

deej(at)deej.net
Guest

Posted: Tue Dec 29, 2015 5:40 pm Post subject: stratux ads-b

Found this nice beginners guide for the Stratux:



https://github.com/ssokol/stratux/wiki/Stratux-Beginner's-Guide



Also the pinouts for the GPS to RPi connection:



https://www.reddit.com/r/stratux/comments/3mf8xg/ry835ai_gps_connections_nonusb/



Here are some options for 3D printed cases.  I printed the yellow one in 

the upper right, and it worked out well.



http://www.thingiverse.com/search/page:1?q=stratux&sa=



And a good broker service for 3D print shops:



https://www.3dhubs.com/



-Dj

-- 

Dj Merrill - N1JOV - EAA Chapter 87

Sportsman 2+2 Builder #7118 N421DJ - http://deej.net/sportsman/

Glastar Flyer N866RH - http://deej.net/glastar/

- The Matronics RV10-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

Display posts from previous:

	Matronics Email Lists Forum Index -> RV10-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum