 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
trigo(at)mail.telepac.pt
Guest
|
 Posted: Tue Apr 19, 2016 2:38 pm Post subject: Powering the EFIS system |
 |
|
Group
I am beginning to install the EFIS G3X system from GARMIN in the RV-10, and I have to put power into (not more not less than) 12 devices (2 Display units, 2 ADAHRS, 1 engine module, 3 autopilot servos and so on).
In some devices there are 2 independent power inputs.
I am trying to figure out which will be the best architecture for the power circuits to these 12 devices.
I know that some of you are against the single Avionics switch, and I am leaning to agree, not including that single point of failure, but how about the distribution system?
I am not searching for opinions on the breaker or fuses discussion, just to know what other people did or recommend to do with busses and circuits.
I should add that I have a dual battery /dual alternator energy system.
All good suggestions welcome!
Thanks
Carlos
 Sem vírus. www.avast.com
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
 |
along(at)aanet.com.au
Guest
|
| Posted: Tue Apr 19, 2016 3:26 pm Post subject: Powering the EFIS system |
|
|
Hi Carlos,
I can only point you to what I did and the reason.
I have configured for IFR and high levels of redundancy.
refer to my build log: www.ozrv10.com and see what I did.
It is very much a personal decision and comfort zone.
Regards,
Andrew
On 20-Apr-16 8:36 AM, Carlos Trigo wrote:
| Quote: | <![endif]--> <![endif]-->
Group
I am beginning to install the EFIS G3X system from GARMIN in the RV-10, and I have to put power into (not more not less than) 12 devices (2 Display units, 2 ADAHRS, 1 engine module, 3 autopilot servos and so on).
In some devices there are 2 independent power inputs.
I am trying to figure out which will be the best architecture for the power circuits to these 12 devices.
I know that some of you are against the single Avionics switch, and I am leaning to agree, not including that single point of failure, but how about the distribution system?
I am not searching for opinions on the breaker or fuses discussion, just to know what other people did or recommend to do with busses and circuits.
I should add that I have a dual battery /dual alternator energy system.
All good suggestions welcome!
Thanks
Carlos
Sem vírus. www.avast.com |
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
philperry9
Joined: 23 Nov 2011
Posts: 381
|
| Posted: Tue Apr 19, 2016 3:26 pm Post subject: Powering the EFIS system |
|
|
Carlos,
The lid is off the can of worms. This should be interesting! I've found that coating my wires in chromate primer has benefits too. 
All seriousness, though I can see people breaking out the flame throwers already, what does your main buss look like? Single Alt / Single Battery? Dual alt (hot/standby) single battery, etc....
Phil
Sent from my iPhone
On Apr 19, 2016, at 5:36 PM, Carlos Trigo <trigo(at)mail.telepac.pt (trigo(at)mail.telepac.pt)> wrote:
| Quote: | <![endif]--> <![endif]-->
Group
I am beginning to install the EFIS G3X system from GARMIN in the RV-10, and I have to put power into (not more not less than) 12 devices (2 Display units, 2 ADAHRS, 1 engine module, 3 autopilot servos and so on).
In some devices there are 2 independent power inputs.
I am trying to figure out which will be the best architecture for the power circuits to these 12 devices.
I know that some of you are against the single Avionics switch, and I am leaning to agree, not including that single point of failure, but how about the distribution system?
I am not searching for opinions on the breaker or fuses discussion, just to know what other people did or recommend to do with busses and circuits.
I should add that I have a dual battery /dual alternator energy system.
All good suggestions welcome!
Thanks
Carlos
Sem vírus. www.avast.com
|
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
davidsoutpost(at)comcast.
Guest
|
| Posted: Tue Apr 19, 2016 6:19 pm Post subject: Powering the EFIS system |
|
|
All my avionics operate off a separate buss which is a blade fuse block. My single avionics switch operates a miniature 30 amp relay that powers the block.
Sent from my Verizon Wireless 4G LTE smartphone
-------- Original message --------
From: Carlos Trigo <trigo(at)mail.telepac.pt>
Date: 04/19/2016 6:36 PM (GMT-05:00)
To: aeroelectric-list(at)matronics.com, rv10-list(at)matronics.com
Subject: RV10-List: Powering the EFIS system
<![endif]--> <![endif]-->
Group
I am beginning to install the EFIS G3X system from GARMIN in the RV-10, and I have to put power into (not more not less than) 12 devices (2 Display units, 2 ADAHRS, 1 engine module, 3 autopilot servos and so on).
In some devices there are 2 independent power inputs.
I am trying to figure out which will be the best architecture for the power circuits to these 12 devices.
I know that some of you are against the single Avionics switch, and I am leaning to agree, not including that single point of failure, but how about the distribution system?
I am not searching for opinions on the breaker or fuses discussion, just to know what other people did or recommend to do with busses and circuits.
I should add that I have a dual battery /dual alternator energy system.
All good suggestions welcome!
Thanks
Carlos
Sem vírus. www.avast.com
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
flying-nut(at)cfl.rr.com
Guest
|
| Posted: Tue Apr 19, 2016 6:36 pm Post subject: Powering the EFIS system |
|
|
On 4/19/2016 10:17 PM, davidsoutpost wrote:
| Quote: | All my avionics operate off a separate buss which is a blade fuse block. My single avionics switch operates a miniature 30 amp relay that powers the block.
|
To minimize the single point failure mode, you should wire the switch to remove power to the relay in the 'on' position, and wire the relay so that when the relay is off it supplies power to the avionics fuses.
No matter which part fails .... the switch or the relay ..... the avionics fuse block still gets power.
Linn
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
davidsoutpost(at)comcast.
Guest
|
| Posted: Tue Apr 19, 2016 6:56 pm Post subject: Powering the EFIS system |
|
|
So I understand this,,,,the buss will always have power to it no matter the switch position?
From: "Linn Walters" <flying-nut(at)cfl.rr.com>
To: rv10-list(at)matronics.com
Sent: Tuesday, April 19, 2016 10:34:22 PM
Subject: Re: Powering the EFIS system
On 4/19/2016 10:17 PM, davidsoutpost wrote:
| Quote: | All my avionics operate off a separate buss which is a blade fuse block. My single avionics switch operates a miniature 30 amp relay that powers the block.
|
To minimize the single point failure mode, you should wire the switch to remove power to the relay in the 'on' position, and wire the relay so that when the relay is off it supplies power to the avionics fuses.
No matter which part fails .... the switch or the relay ..... the avionics fuse block still gets power.
Linn
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
flying-nut(at)cfl.rr.com
Guest
|
| Posted: Tue Apr 19, 2016 7:39 pm Post subject: Powering the EFIS system |
|
|
On 4/19/2016 10:55 PM, David Clifford wrote:
| Quote: | So I understand this,,,,the buss will always have power to it no matter the switch position?
|
No. When the SPDT switch is in the 'off' position it supplies power to the relay which is 'on' and the NC contacts remove power to the buss.
It's the inverse of what most builders will do .... SP switch on, relay on to supply power to the buss through the NO contacts. With this wiring method the relay is not needed if the switch has the proper current rating. I don't know what David's panel current draw really is but think it's way less than 30 amps.
Fuses are there to protect the wires from excess current, not the equipment attached. So, if you have 6 ea. 5A fuses ..... that's 30A! If every electrical item in my plane is on and stable I draw less than 6 amps. Strobes on startup and radio transmitting will add some more.
Linn
| Quote: |
From: "Linn Walters" <flying-nut(at)cfl.rr.com> (flying-nut(at)cfl.rr.com)
To: rv10-list(at)matronics.com (rv10-list(at)matronics.com)
Sent: Tuesday, April 19, 2016 10:34:22 PM
Subject: Re: Powering the EFIS system
On 4/19/2016 10:17 PM, davidsoutpost wrote:
| Quote: | All my avionics operate off a separate buss which is a blade fuse block. My single avionics switch operates a miniature 30 amp relay that powers the block.
|
To minimize the single point failure mode, you should wire the switch to remove power to the relay in the 'on' position, and wire the relay so that when the relay is off it supplies power to the avionics fuses.
No matter which part fails .... the switch or the relay ..... the avionics fuse block still gets power.
Linn
|
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
trigo(at)mail.telepac.pt
Guest
|
| Posted: Wed Apr 20, 2016 11:56 am Post subject: Powering the EFIS system |
|
|
Thank you David
Please indicate the part# and source for the miniature relay you used.
And a picture of your fuse block installation would also be very welcome …
Cheers
Carlos
From: owner-rv10-list-server(at)matronics.com [mailto:owner-rv10-list-server(at)matronics.com] On Behalf Of davidsoutpost
Sent: quarta-feira, 20 de Abril de 2016 03:18
To: rv10-list(at)matronics.com
Subject: RE: Powering the EFIS system
All my avionics operate off a separate buss which is a blade fuse block. My single avionics switch operates a miniature 30 amp relay that powers the block.
Sent from my Verizon Wireless 4G LTE smartphone
-------- Original message --------
From: Carlos Trigo <trigo(at)mail.telepac.pt (trigo(at)mail.telepac.pt)>
Date: 04/19/2016 6:36 PM (GMT-05:00)
To: aeroelectric-list(at)matronics.com (aeroelectric-list(at)matronics.com), rv10-list(at)matronics.com (rv10-list(at)matronics.com)
Subject: Powering the EFIS system
Group
I am beginning to install the EFIS G3X system from GARMIN in the RV-10, and I have to put power into (not more not less than) 12 devices (2 Display units, 2 ADAHRS, 1 engine module, 3 autopilot servos and so on).
In some devices there are 2 independent power inputs.
I am trying to figure out which will be the best architecture for the power circuits to these 12 devices.
I know that some of you are against the single Avionics switch, and I am leaning to agree, not including that single point of failure, but how about the distribution system?
I am not searching for opinions on the breaker or fuses discussion, just to know what other people did or recommend to do with busses and circuits.
I should add that I have a dual battery /dual alternator energy system.
All good suggestions welcome!
Thanks
Carlos
Sem vírus. www.avast.com
 Sem vírus. www.avast.com
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
stein(at)steinair.com
Guest
|
| Posted: Wed Apr 20, 2016 12:09 pm Post subject: Powering the EFIS system |
|
|
While you can build this up yourself much cheaper (you can get a standard relay with the diode in it for around $15 or so) , but basically this is the same thing we do for our customers and have pre-wired it for them with the relay, buss bar, etc.. all ready to go…
http://steinair.com/storedetail.cfm?productid=672
Cheers,
Stein
Do not archive
From: owner-rv10-list-server(at)matronics.com [mailto:owner-rv10-list-server(at)matronics.com] On Behalf Of Carlos Trigo
Sent: Wednesday, April 20, 2016 5:26 AM
To: rv10-list(at)matronics.com
Subject: RE: Powering the EFIS system
Thank you David
Please indicate the part# and source for the miniature relay you used.
And a picture of your fuse block installation would also be very welcome …
Cheers
Carlos
From: owner-rv10-list-server(at)matronics.com (owner-rv10-list-server(at)matronics.com) [mailto:owner-rv10-list-server(at)matronics.com (owner-rv10-list-server(at)matronics.com)] On Behalf Of davidsoutpost
Sent: quarta-feira, 20 de Abril de 2016 03:18
To: rv10-list(at)matronics.com (rv10-list(at)matronics.com)
Subject: RE: Powering the EFIS system
All my avionics operate off a separate buss which is a blade fuse block. My single avionics switch operates a miniature 30 amp relay that powers the block.
Sent from my Verizon Wireless 4G LTE smartphone
-------- Original message --------
From: Carlos Trigo <trigo(at)mail.telepac.pt (trigo(at)mail.telepac.pt)>
Date: 04/19/2016 6:36 PM (GMT-05:00)
To: aeroelectric-list(at)matronics.com (aeroelectric-list(at)matronics.com), rv10-list(at)matronics.com (rv10-list(at)matronics.com)
Subject: Powering the EFIS system
Group
I am beginning to install the EFIS G3X system from GARMIN in the RV-10, and I have to put power into (not more not less than) 12 devices (2 Display units, 2 ADAHRS, 1 engine module, 3 autopilot servos and so on).
In some devices there are 2 independent power inputs.
I am trying to figure out which will be the best architecture for the power circuits to these 12 devices.
I know that some of you are against the single Avionics switch, and I am leaning to agree, not including that single point of failure, but how about the distribution system?
I am not searching for opinions on the breaker or fuses discussion, just to know what other people did or recommend to do with busses and circuits.
I should add that I have a dual battery /dual alternator energy system.
All good suggestions welcome!
Thanks
Carlos
Sem vírus. www.avast.com
Sem vírus. www.avast.com
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
carl.froehlich(at)verizon
Guest
|
| Posted: Wed Apr 20, 2016 12:28 pm Post subject: Powering the EFIS system |
|
|
Stein,
As you promote an avionics relay type approach, I’d appreciate an understanding of why one would want to use this or any “avionics master” switch scheme. As far as I can see this adds a unnecessary common failure mode for loss of the panel.
Carl
From: owner-rv10-list-server(at)matronics.com [mailto:owner-rv10-list-server(at)matronics.com] On Behalf Of Stein Bruch
Sent: Wednesday, April 20, 2016 4:08 PM
To: rv10-list(at)matronics.com
Subject: RE: Powering the EFIS system
While you can build this up yourself much cheaper (you can get a standard relay with the diode in it for around $15 or so) , but basically this is the same thing we do for our customers and have pre-wired it for them with the relay, buss bar, etc.. all ready to go…
http://steinair.com/storedetail.cfm?productid=672
Cheers,
Stein
Do not archive
From: owner-rv10-list-server(at)matronics.com (owner-rv10-list-server(at)matronics.com) [mailto:owner-rv10-list-server(at)matronics.com (owner-rv10-list-server(at)matronics.com)] On Behalf Of Carlos Trigo
Sent: Wednesday, April 20, 2016 5:26 AM
To: rv10-list(at)matronics.com (rv10-list(at)matronics.com)
Subject: RE: Powering the EFIS system
Thank you David
Please indicate the part# and source for the miniature relay you used.
And a picture of your fuse block installation would also be very welcome …
Cheers
Carlos
From: owner-rv10-list-server(at)matronics.com (owner-rv10-list-server(at)matronics.com) [mailto:owner-rv10-list-server(at)matronics.com (owner-rv10-list-server(at)matronics.com)] On Behalf Of davidsoutpost
Sent: quarta-feira, 20 de Abril de 2016 03:18
To: rv10-list(at)matronics.com (rv10-list(at)matronics.com)
Subject: RE: Powering the EFIS system
All my avionics operate off a separate buss which is a blade fuse block. My single avionics switch operates a miniature 30 amp relay that powers the block.
Sent from my Verizon Wireless 4G LTE smartphone
-------- Original message --------
From: Carlos Trigo <trigo(at)mail.telepac.pt (trigo(at)mail.telepac.pt)>
Date: 04/19/2016 6:36 PM (GMT-05:00)
To: aeroelectric-list(at)matronics.com (aeroelectric-list(at)matronics.com), rv10-list(at)matronics.com (rv10-list(at)matronics.com)
Subject: Powering the EFIS system
Group
I am beginning to install the EFIS G3X system from GARMIN in the RV-10, and I have to put power into (not more not less than) 12 devices (2 Display units, 2 ADAHRS, 1 engine module, 3 autopilot servos and so on).
In some devices there are 2 independent power inputs.
I am trying to figure out which will be the best architecture for the power circuits to these 12 devices.
I know that some of you are against the single Avionics switch, and I am leaning to agree, not including that single point of failure, but how about the distribution system?
I am not searching for opinions on the breaker or fuses discussion, just to know what other people did or recommend to do with busses and circuits.
I should add that I have a dual battery /dual alternator energy system.
All good suggestions welcome!
Thanks
Carlos
Sem vírus. www.avast.com
Sem vírus. www.avast.com
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
stein(at)steinair.com
Guest
|
| Posted: Wed Apr 20, 2016 1:11 pm Post subject: Powering the EFIS system |
|
|
I really don’t desire to get into that primer war! J
That said, if you desire to have an avionics master switch (which I’m not necessarily promoting or not promoting) a relay is almost always a “must” because most switches are not rated to handle that current load. Of course you can design a system so as to not need or want an avionics master, but if you do then a relay is usually (not always) a good idea. If you want an avionics master and your system is designed for one, then go for it. If you don’t want one or design around it, then don’t use one…
Is that enough of a politicians answer!?!?! Ha!
Cheers,
Stein
From: owner-rv10-list-server(at)matronics.com [mailto:owner-rv10-list-server(at)matronics.com] On Behalf Of Carl Froehlich
Sent: Wednesday, April 20, 2016 3:28 PM
To: rv10-list(at)matronics.com
Subject: RE: Powering the EFIS system
Stein,
As you promote an avionics relay type approach, I’d appreciate an understanding of why one would want to use this or any “avionics master” switch scheme. As far as I can see this adds a unnecessary common failure mode for loss of the panel.
Carl
From: owner-rv10-list-server(at)matronics.com (owner-rv10-list-server(at)matronics.com) [mailto:owner-rv10-list-server(at)matronics.com (owner-rv10-list-server(at)matronics.com)] On Behalf Of Stein Bruch
Sent: Wednesday, April 20, 2016 4:08 PM
To: rv10-list(at)matronics.com (rv10-list(at)matronics.com)
Subject: RE: Powering the EFIS system
While you can build this up yourself much cheaper (you can get a standard relay with the diode in it for around $15 or so) , but basically this is the same thing we do for our customers and have pre-wired it for them with the relay, buss bar, etc.. all ready to go…
http://steinair.com/storedetail.cfm?productid=672
Cheers,
Stein
Do not archive
From: owner-rv10-list-server(at)matronics.com (owner-rv10-list-server(at)matronics.com) [mailto:owner-rv10-list-server(at)matronics.com (owner-rv10-list-server(at)matronics.com)] On Behalf Of Carlos Trigo
Sent: Wednesday, April 20, 2016 5:26 AM
To: rv10-list(at)matronics.com (rv10-list(at)matronics.com)
Subject: RE: Powering the EFIS system
Thank you David
Please indicate the part# and source for the miniature relay you used.
And a picture of your fuse block installation would also be very welcome …
Cheers
Carlos
From: owner-rv10-list-server(at)matronics.com (owner-rv10-list-server(at)matronics.com) [mailto:owner-rv10-list-server(at)matronics.com (owner-rv10-list-server(at)matronics.com)] On Behalf Of davidsoutpost
Sent: quarta-feira, 20 de Abril de 2016 03:18
To: rv10-list(at)matronics.com (rv10-list(at)matronics.com)
Subject: RE: Powering the EFIS system
All my avionics operate off a separate buss which is a blade fuse block. My single avionics switch operates a miniature 30 amp relay that powers the block.
Sent from my Verizon Wireless 4G LTE smartphone
-------- Original message --------
From: Carlos Trigo <trigo(at)mail.telepac.pt (trigo(at)mail.telepac.pt)>
Date: 04/19/2016 6:36 PM (GMT-05:00)
To: aeroelectric-list(at)matronics.com (aeroelectric-list(at)matronics.com), rv10-list(at)matronics.com (rv10-list(at)matronics.com)
Subject: Powering the EFIS system
Group
I am beginning to install the EFIS G3X system from GARMIN in the RV-10, and I have to put power into (not more not less than) 12 devices (2 Display units, 2 ADAHRS, 1 engine module, 3 autopilot servos and so on).
In some devices there are 2 independent power inputs.
I am trying to figure out which will be the best architecture for the power circuits to these 12 devices.
I know that some of you are against the single Avionics switch, and I am leaning to agree, not including that single point of failure, but how about the distribution system?
I am not searching for opinions on the breaker or fuses discussion, just to know what other people did or recommend to do with busses and circuits.
I should add that I have a dual battery /dual alternator energy system.
All good suggestions welcome!
Thanks
Carlos
Sem vírus. www.avast.com
Sem vírus. www.avast.com
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
davidsoutpost(at)comcast.
Guest
|
| Posted: Wed Apr 20, 2016 1:19 pm Post subject: Powering the EFIS system |
|
|
I used one of these I had laying around from another project. Its mounted behind the IP on the sub-panel, and is wired with 10 gauge from my main 12 volt power stud to the fuse block. Fuse blocks I used are from Steinair. The fuse blocks are mounted also behind the IP on the sub-panel. Fuse blocks are behind the pilot side accessible by removing the GDU 370 & GDU 375 displays. Sorry but I don't have a picture handy
From: "Carlos Trigo" <trigo(at)mail.telepac.pt>
To: rv10-list(at)matronics.com
Sent: Wednesday, April 20, 2016 6:26:19 AM
Subject: RE: Powering the EFIS system
Thank you David
Please indicate the part# and source for the miniature relay you used.
And a picture of your fuse block installation would also be very welcome …
Cheers
Carlos
From: owner-rv10-list-server(at)matronics.com [mailto:owner-rv10-list-server(at)matronics.com] On Behalf Of davidsoutpost
Sent: quarta-feira, 20 de Abril de 2016 03:18
To: rv10-list(at)matronics.com
Subject: RE: RV10-List: Powering the EFIS system
All my avionics operate off a separate buss which is a blade fuse block. My single avionics switch operates a miniature 30 amp relay that powers the block.
Sent from my Verizon Wireless 4G LTE smartphone
-------- Original message --------
From: Carlos Trigo <trigo(at)mail.telepac.pt (trigo(at)mail.telepac.pt)>
Date: 04/19/2016 6:36 PM (GMT-05:00)
To: aeroelectric-list(at)matronics.com (aeroelectric-list(at)matronics.com), rv10-list(at)matronics.com (rv10-list(at)matronics.com)
Subject: Powering the EFIS system
Group
I am beginning to install the EFIS G3X system from GARMIN in the RV-10, and I have to put power into (not more not less than) 12 devices (2 Display units, 2 ADAHRS, 1 engine module, 3 autopilot servos and so on).
In some devices there are 2 independent power inputs.
I am trying to figure out which will be the best architecture for the power circuits to these 12 devices.
I know that some of you are against the single Avionics switch, and I am leaning to agree, not including that single point of failure, but how about the distribution system?
I am not searching for opinions on the breaker or fuses discussion, just to know what other people did or recommend to do with busses and circuits.
I should add that I have a dual battery /dual alternator energy system.
All good suggestions welcome!
Thanks
Carlos
Sem vírus. www.avast.com
Sem vírus. www.avast.com
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
| Description: |
|
| Filesize: |
66.31 KB |
| Viewed: |
9658 Time(s) |
|
|
|
| Back to top |
|
|
jdriggs49(at)MSN.COM
Guest
|
| Posted: Wed Apr 20, 2016 3:14 pm Post subject: Powering the EFIS system |
|
|
Relays are really pretty reliable. Also are very much cheaper than the electronic systems. Spend $15 for and extra one and carry it with you as a spare.
Sent from my iPhone
On Apr 20, 2016, at 2:15 PM, Stein Bruch <stein(at)steinair.com (stein(at)steinair.com)> wrote:
| Quote: | v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} <![endif]--> <![endif]--> <![endif]-->
I really dont desire to get into that primer war! J
That said, if you desire to have an avionics master switch (which Im not necessarily promoting or not promoting) a relay is almost always a must because most switches are not rated to handle that current load. Of course you can design a system so as to not need or want an avionics master, but if you do then a relay is usually (not always) a good idea. If you want an avionics master and your system is designed for one, then go for it. If you dont want one or design around it, then dont use one
Is that enough of a politicians answer!?!?! Ha!
Cheers,
Stein
From: owner-rv10-list-server(at)matronics.com (owner-rv10-list-server(at)matronics.com) [mailto:owner-rv10-list-server(at)matronics.com (owner-rv10-list-server(at)matronics.com)] On Behalf Of Carl Froehlich
Sent: Wednesday, April 20, 2016 3:28 PM
To: rv10-list(at)matronics.com (rv10-list(at)matronics.com)
Subject: RE: Powering the EFIS system
Stein,
As you promote an avionics relay type approach, Id appreciate an understanding of why one would want to use this or any avionics master switch scheme. As far as I can see this adds a unnecessary common failure mode for loss of the panel.
Carl
From: owner-rv10-list-server(at)matronics.com (owner-rv10-list-server(at)matronics.com) [mailto:owner-rv10-list-server(at)matronics.com (owner-rv10-list-server(at)matronics.com)] On Behalf Of Stein Bruch
Sent: Wednesday, April 20, 2016 4:08 PM
To: rv10-list(at)matronics.com (rv10-list(at)matronics.com)
Subject: RE: Powering the EFIS system
While you can build this up yourself much cheaper (you can get a standard relay with the diode in it for around $15 or so) , but basically this is the same thing we do for our customers and have pre-wired it for them with the relay, buss bar, etc.. all ready to go
http://steinair.com/storedetail.cfm?productid=672
Cheers,
Stein
Do not archive
From: owner-rv10-list-server(at)matronics.com (owner-rv10-list-server(at)matronics.com) [mailto:owner-rv10-list-server(at)matronics.com (owner-rv10-list-server(at)matronics.com)] On Behalf Of Carlos Trigo
Sent: Wednesday, April 20, 2016 5:26 AM
To: rv10-list(at)matronics.com (rv10-list(at)matronics.com)
Subject: RE: Powering the EFIS system
Thank you David
Please indicate the part# and source for the miniature relay you used.
And a picture of your fuse block installation would also be very welcome
Cheers
Carlos
From: owner-rv10-list-server(at)matronics.com (owner-rv10-list-server(at)matronics.com) [mailto:owner-rv10-list-server(at)matronics.com (owner-rv10-list-server(at)matronics.com)] On Behalf Of davidsoutpost
Sent: quarta-feira, 20 de Abril de 2016 03:18
To: rv10-list(at)matronics.com (rv10-list(at)matronics.com)
Subject: RE: Powering the EFIS system
All my avionics operate off a separate buss which is a blade fuse block. My single avionics switch operates a miniature 30 amp relay that powers the block.
Sent from my Verizon Wireless 4G LTE smartphone
-------- Original message --------
From: Carlos Trigo <trigo(at)mail.telepac.pt (trigo(at)mail.telepac.pt)>
Date: 04/19/2016 6:36 PM (GMT-05:00)
To: aeroelectric-list(at)matronics.com (aeroelectric-list(at)matronics.com), rv10-list(at)matronics.com (rv10-list(at)matronics.com)
Subject: Powering the EFIS system
Group
I am beginning to install the EFIS G3X system from GARMIN in the RV-10, and I have to put power into (not more not less than) 12 devices (2 Display units, 2 ADAHRS, 1 engine module, 3 autopilot servos and so on).
In some devices there are 2 independent power inputs.
I am trying to figure out which will be the best architecture for the power circuits to these 12 devices.
I know that some of you are against the single Avionics switch, and I am leaning to agree, not including that single point of failure, but how about the distribution system?
I am not searching for opinions on the breaker or fuses discussion, just to know what other people did or recommend to do with busses and circuits.
I should add that I have a dual battery /dual alternator energy system.
All good suggestions welcome!
Thanks
Carlos
Sem vrus. www.avast.com
Sem vrus. www.avast.com
|
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
Bob Turner
Joined: 03 Jan 2009
Posts: 885
Location: Castro Valley, CA
|
| Posted: Wed Apr 20, 2016 5:32 pm Post subject: Re: Powering the EFIS system |
|
|
I don't like the 'wire the relay backwards (avionics on when relay off)' approach.
1. Every time you turn on the master you give your radios a short pulse of power (until the relay pulls up)
2. If your starter pulls enough current to result in 'brown-out (significant drop in buss voltage) your avionics power relay may drop out at exactly the wrong time - subjecting your avionics to a low voltage. Some modern avionics do not tolerate low input voltages very well.
At the least I'd look for a relay with low drop out voltage ratings.
Switches and relays are cheap enough to put in two, one for backup.
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
_________________
Bob Turner
RV-10 QB |
|
| Back to top |
|
|
flying-nut(at)cfl.rr.com
Guest
|
| Posted: Wed Apr 20, 2016 6:02 pm Post subject: Powering the EFIS system |
|
|
On 4/20/2016 9:32 PM, Bob Turner wrote:
| Quote: |
I don't like the 'wire the relay backwards (avionics on when relay off)' approach.
That's OK too. I'd hate to have a failure of either the switch or relay
|
.... wired conventionally ..... that killed all my avionics.
| Quote: | 1. Every time you turn on the master you give your radios a short pulse of power (until the relay pulls up)
I've never hung a 'scope on the avionics buss, but I suspect the
|
avionics inrush current would keep that pulse rather small.
| Quote: | 2. If your starter pulls enough current to result in 'brown-out (significant drop in buss voltage) your avionics power relay may drop out at exactly the wrong time - subjecting your avionics to a low voltage. Some modern avionics do not tolerate low input voltages very well.
I have 'exit sign' batteries for each of my two EFIS panels as backups
|
for alternator/ships battery failure. I can power up the EFIS without
turning on ships power. No brownout, no reboot no matter how low the
ships power gets.
| Quote: | At the least I'd look for a relay with low drop out voltage ratings.
Not a bad idea.
|
Linn
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
johngoodman
Joined: 18 Sep 2006
Posts: 530
Location: GA
|
| Posted: Thu Apr 21, 2016 5:12 am Post subject: Re: Powering the EFIS system |
|
|
I used the Vertical Power solution. Take a look at it.
John
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
_________________
#40572 Phase One complete in 2011 |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
