 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
dfritz(at)bpgsim.com
Guest
|
 Posted: Mon Nov 21, 2016 9:52 am Post subject: Fuel Valve Mounting Bracket |
 |
|
My quick build fuselage came with the mounting bracket F1048C-1
installed facing down. There was a tag attached saying that it should
be reinstalled face up (the U facing up). They also sent me a new
bracket in case I messed up the installed one removing it. I am now in
the process of installing the fuel valve, an Andair unit. I have made a
mounting plate to rivet to the F1048C-1 so that mounting holes will
match the Andair valve. I am ready to flip the mounting bracket but
find the flush rivets on the aft end of the bracket are 1/4 inch from
the vertical panel of the seat mounting structure. I do not have a
drill that will fit in that close of an area and my rivet gun is too
wide to drive a rivet in that space. How have others made this change?
Dave
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
 |
Kelly McMullen
Joined: 16 Apr 2008
Posts: 1188
Location: Sun Lakes AZ
|
| Posted: Mon Nov 21, 2016 12:52 pm Post subject: Fuel Valve Mounting Bracket |
|
|
I cut the sides off the bracket and riveted two pieces of angle aluminum to get the width I need, got the Andair extension, mounted valve as low as possible, then cut the extension to required length. I did not want the valve up near the top of the tunnel, as that creates potential for vapor or air lock. I got the right angle fitting from Van's catalog to make the connection at the bottom of the valve.
-sent from the I-droid implanted in my forearm
On Mon, Nov 21, 2016 at 10:52 AM, David J. Fritzsche <dfritz(at)bpgsim.com (dfritz(at)bpgsim.com)> wrote:
| Quote: | --> RV10-List message posted by: "David J. Fritzsche" <dfritz(at)bpgsim.com (dfritz(at)bpgsim.com)>
My quick build fuselage came with the mounting bracket F1048C-1 installed facing down. There was a tag attached saying that it should be reinstalled face up (the U facing up). They also sent me a new bracket in case I messed up the installed one removing it. I am now in the process of installing the fuel valve, an Andair unit. I have made a mounting plate to rivet to the F1048C-1 so that mounting holes will match the Andair valve. I am ready to flip the mounting bracket but find the flush rivets on the aft end of the bracket are 1/4 inch from the vertical panel of the seat mounting structure. I do not have a drill that will fit in that close of an area and my rivet gun is too wide to drive a rivet in that space. How have others made this change?
Dave
====================================
br> fts!)
r> > /www.aeroelectric.com" rel="noreferrer" target="_blank">www.aeroelectric.com
w.buildersbooks.com" rel="noreferrer" target="_blank">www.buildersbooks.com
p.com" rel="noreferrer" target="_blank">www.homebuilthelp.com
e.com" rel="noreferrer" target="_blank">www.mypilotstore.com
" rel="noreferrer" target="_blank">www.mrrace.com
rel="noreferrer" target="_blank">http://www.matronics.com/contribution
     -Matt Dralle, List Admin.
====================================
-List" rel="noreferrer" target="_blank">http://www.matronics.com/Navigator?RV10-List
====================================
FORUMS -
eferrer" target="_blank">http://forums.matronics.com
====================================
WIKI -
errer" target="_blank">http://wiki.matronics.com
====================================
b Site -
     -Matt Dralle, List Admin.
rel="noreferrer" target="_blank">http://www.matronics.com/contribution
====================================
|
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
_________________
Kelly McMullen
A&P/IA, EAA Tech Counselor
KCHD |
|
| Back to top |
|
|
glastar(at)gmx.net
Guest
|
| Posted: Tue Nov 22, 2016 1:32 am Post subject: Fuel Valve Mounting Bracket |
|
|
Dave,
that is an interesting statement, as according plans facing down is correct. As I did another setup (Andair) I had to swap it as well; a long 3-4" drill bit and a good, deep mark in the center, did allow me to drill it out, slightly bend in the middle. I did use a bucking bar on both sides and had the mushroom set on the outside bucking bar (you need a helper!) with that approach I was able to set that last rivet however it took 2 attemps!
[img]cid:part1.06DD0867.ED6FB5E0(at)gmx.net[/img]
Werner
On 21.11.2016 18:52, David J. Fritzsche wrote:
| Quote: | --> RV10-List message posted by: "David J. Fritzsche" <dfritz(at)bpgsim.com> (dfritz(at)bpgsim.com)
My quick build fuselage came with the mounting bracket F1048C-1 installed facing down. There was a tag attached saying that it should be reinstalled face up (the U facing up). They also sent me a new bracket in case I messed up the installed one removing it. I am now in the process of installing the fuel valve, an Andair unit. I have made a mounting plate to rivet to the F1048C-1 so that mounting holes will match the Andair valve. I am ready to flip the mounting bracket but find the flush rivets on the aft end of the bracket are 1/4 inch from the vertical panel of the seat mounting structure. I do not have a drill that will fit in that close of an area and my rivet gun is too wide to drive a rivet in that space. How have others made this change?
|
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
| Description: |
|
| Filesize: |
1.38 MB |
| Viewed: |
3191 Time(s) |
|
|
|
| Back to top |
|
|
dfritz(at)bpgsim.com
Guest
|
| Posted: Tue Nov 22, 2016 12:29 pm Post subject: Fuel Valve Mounting Bracket |
|
|
Kelly,
The only right angle fittings I can find in Van's catalog are tube/pipe. Both my valve and filter have male tubing connections. I would need a right angle with female tube connections on both ends.
Dave
| Quote: | ~~~~~~~~~~~~~~~~~~
David J. Fritzsche
Professor, Retired
Penn State
~~~~~~~~~~~~~~~~~~ |
On 11/21/2016 12:51 PM, Kelly McMullen wrote:
| Quote: | I cut the sides off the bracket and riveted two pieces of angle aluminum to get the width I need, got the Andair extension, mounted valve as low as possible, then cut the extension to required length. I did not want the valve up near the top of the tunnel, as that creates potential for vapor or air lock. I got the right angle fitting from Van's catalog to make the connection at the bottom of the valve.
-sent from the I-droid implanted in my forearm
On Mon, Nov 21, 2016 at 10:52 AM, David J. Fritzsche <dfritz(at)bpgsim.com (dfritz(at)bpgsim.com)> wrote:
| Quote: | --> RV10-List message posted by: "David J. Fritzsche" <dfritz(at)bpgsim.com (dfritz(at)bpgsim.com)>
My quick build fuselage came with the mounting bracket F1048C-1 installed facing down. There was a tag attached saying that it should be reinstalled face up (the U facing up). They also sent me a new bracket in case I messed up the installed one removing it. I am now in the process of installing the fuel valve, an Andair unit. I have made a mounting plate to rivet to the F1048C-1 so that mounting holes will match the Andair valve. I am ready to flip the mounting bracket but find the flush rivets on the aft end of the bracket are 1/4 inch from the vertical panel of the seat mounting structure. I do not have a drill that will fit in that close of an area and my rivet gun is too wide to drive a rivet in that space. How have others made this change?
Dave
====================================
br> fts!)
r> > /www.aeroelectric.com" rel="noreferrer" target="_blank">www.aeroelectric.com
w.buildersbooks.com" rel="noreferrer" target="_blank">www.buildersbooks.com
p.com" rel="noreferrer" target="_blank">www.homebuilthelp.com
e.com" rel="noreferrer" target="_blank">www.mypilotstore.com
" rel="noreferrer" target="_blank">www.mrrace.com
rel="noreferrer" target="_blank">http://www.matronics.com/contribution
     -Matt Dralle, List Admin.
====================================
-List" rel="noreferrer" target="_blank">http://www.matronics.com/Navigator?RV10-List
====================================
FORUMS -
eferrer" target="_blank">http://forums.matronics.com
====================================
WIKI -
errer" target="_blank">http://wiki.matronics.com
====================================
b Site -
     -Matt Dralle, List Admin.
rel="noreferrer" target="_blank">http://www.matronics.com/contribution
====================================
|
|
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
Kelly McMullen
Joined: 16 Apr 2008
Posts: 1188
Location: Sun Lakes AZ
|
| Posted: Tue Nov 22, 2016 5:53 pm Post subject: Fuel Valve Mounting Bracket |
|
|
It is called the F Swivel Tee. There is only one female fitting, as the other two are intended to have female flared fittings connected to them, like virtually all of the fuel system connections.
-sent from the I-droid implanted in my forearm
On Tue, Nov 22, 2016 at 1:29 PM, David J. Fritzsche <dfritz(at)bpgsim.com (dfritz(at)bpgsim.com)> wrote:
| Quote: |
Kelly,
The only right angle fittings I can find in Van's catalog are tube/pipe. Both my valve and filter have male tubing connections. I would need a right angle with female tube connections on both ends.
Dave
| Quote: | ~~~~~~~~~~~~~~~~~~
David J. Fritzsche
Professor, Retired
Penn State
~~~~~~~~~~~~~~~~~~ |
On 11/21/2016 12:51 PM, Kelly McMullen wrote:
| Quote: | I cut the sides off the bracket and riveted two pieces of angle aluminum to get the width I need, got the Andair extension, mounted valve as low as possible, then cut the extension to required length. I did not want the valve up near the top of the tunnel, as that creates potential for vapor or air lock. I got the right angle fitting from Van's catalog to make the connection at the bottom of the valve.
-sent from the I-droid implanted in my forearm
On Mon, Nov 21, 2016 at 10:52 AM, David J. Fritzsche <dfritz(at)bpgsim.com (dfritz(at)bpgsim.com)> wrote:
| Quote: | --> RV10-List message posted by: "David J. Fritzsche" <dfritz(at)bpgsim.com (dfritz(at)bpgsim.com)>
My quick build fuselage came with the mounting bracket F1048C-1 installed facing down. There was a tag attached saying that it should be reinstalled face up (the U facing up). They also sent me a new bracket in case I messed up the installed one removing it. I am now in the process of installing the fuel valve, an Andair unit. I have made a mounting plate to rivet to the F1048C-1 so that mounting holes will match the Andair valve. I am ready to flip the mounting bracket but find the flush rivets on the aft end of the bracket are 1/4 inch from the vertical panel of the seat mounting structure. I do not have a drill that will fit in that close of an area and my rivet gun is too wide to drive a rivet in that space. How have others made this change?
Dave
====================================
br> fts!)
r> > /www.aeroelectric.com" rel="noreferrer" target="_blank">www.aeroelectric.com
w.buildersbooks.com" rel="noreferrer" target="_blank">www.buildersbooks.com
p.com" rel="noreferrer" target="_blank">www.homebuilthelp.com
e.com" rel="noreferrer" target="_blank">www.mypilotstore.com
" rel="noreferrer" target="_blank">www.mrrace.com
rel="noreferrer" target="_blank">http://www.matronics.com/contribution
     -Matt Dralle, List Admin.
====================================
-List" rel="noreferrer" target="_blank">http://www.matronics.com/Navigator?RV10-List
====================================
FORUMS -
eferrer" target="_blank">http://forums.matronics.com
====================================
WIKI -
errer" target="_blank">http://wiki.matronics.com
====================================
b Site -
     -Matt Dralle, List Admin.
rel="noreferrer" target="_blank">http://www.matronics.com/contribution
====================================
|
|
|
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
_________________
Kelly McMullen
A&P/IA, EAA Tech Counselor
KCHD |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
