Matronics Email Lists :: View topic

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

TR$ Jack Options

Matronics Email Lists Forum Index -> KIS-List

View previous topic :: View next topic

Author Message

mike(at)vision499.com
Guest

Posted: Sun Jun 03, 2018 5:46 pm Post subject: TR$ Jack Options

Does anybody have a clever idea that will make it easy to jack up and support a TR4 to remove and work on the wheels and brakes etc.

 

I often think I should have made provision for an eyebolt to be screwed into the top of the wing near the wing positioning bolt and then you could just lift it with an engine hoist.

 

I’m crawling underneath the fuselage and cannot see a convenient jacking and support point.

 

My neighbor who has an RV has a clever “goodie” that fits into the axle, I will have a closer look at that and see if I can make something similar.

 

Thanks

 

Mike

 

Mike Pienaar

mike(at)vision499.com (ike(at)vision499.com)

Home: +1 250-999-8121

Mike cell: +1 250-885-0554

1-1100 Tulip Ave, Victoria, BC, V8Z 0A2

 

  	          		Virus-free. www.avast.com 		 	 [url=#DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2] [/url]

- The Matronics KIS-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?KIS-List

GalinHdz

Joined: 08 Nov 2017
Posts: 150

Posted: Mon Jun 04, 2018 5:32 am Post subject: TR$ Jack Options

FWIW: I bought a small "low profile" hydraulic 2 ton floor jack. I chock the other wheels so the airplane doesn't shift. I carefully slide the jack under the landing gear metal part far enough so I can lift it up. Once high enough, I slide a slightly modified portable saw horse with a thick movers blanket under the wing then slowly lower the airplane on the sawhorse. Now I can take the floor jack out and work on the tire without fear of it falling off the floor jack. When done, I reverse the process. It works very well and one person can do it easily.



I have attached photos of the floor jack and the saw horse so you have an idea of what I am talking about. I am actually undergoing the annual condition inspection and will be re-packing the airplane main tire bearings today. I will take pictures of the process and post them here.

  



On Sun, Jun 3, 2018 at 9:46 PM,  <mike(at)vision499.com (mike(at)vision499.com)> wrote:

 	  Quote: 	
		  

Does anybody have a clever idea that will make it easy to jack up and support a TR4 to remove and work on the wheels and brakes etc.

 

I often think I should have made provision for an eyebolt to be screwed into the top of the wing near the wing positioning bolt and then you could just lift it with an engine hoist.

 

I’m crawling underneath the fuselage and cannot see a convenient jacking and support point.

 

My neighbor who has an RV has a clever “goodie” that fits into the axle, I will have a closer look at that and see if I can make something similar.

 

Thanks

 

Mike

 

Mike Pienaar

mike(at)vision499.com (ike(at)vision499.com)[u][/u]

Home: +1 250-999-8121

Mike cell: +1 250-885-0554

1-1100 Tulip Ave, Victoria, BC, V8Z 0A2

 



  	          		Virus-free. www.avast.com 		 	 [url=#m_785057707629846006_DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2] [/url]

- The Matronics KIS-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?KIS-List

Saw_Horse.jpg

Description:

Filesize:

184.32 KB

Viewed:

5031 Time(s)

FLoor_jack.jpeg

Description:

Filesize:

17.1 KB

Viewed:

5031 Time(s)

mike(at)vision499.com
Guest

Posted: Mon Jun 04, 2018 8:19 am Post subject: TR$ Jack Options

Thanks you very much Galin,

 

I was concerned about damaging the brake and wheel if I tried to jack it on the bottom of the landing gear and would not have thought of resting it on the wing. Thanks for your help

 

Mike

 

From: owner-kis-list-server(at)matronics.com [mailto:owner-kis-list-server(at)matronics.com] On Behalf Of Galin Hernandez

Sent: June 4, 2018 6:25 AM

To: kis-list(at)matronics.com

Subject: Re: TR$ Jack Options

 

FWIW: I bought a small "low profile" hydraulic 2 ton floor jack. I chock the other wheels so the airplane doesn't shift. I carefully slide the jack under the landing gear metal part far enough so I can lift it up. Once high enough, I slide a slightly modified portable saw horse with a thick movers blanket under the wing then slowly lower the airplane on the sawhorse. Now I can take the floor jack out and work on the tire without fear of it falling off the floor jack. When done, I reverse the process. It works very well and one person can do it easily.

 



I have attached photos of the floor jack and the saw horse so you have an idea of what I am talking about. I am actually undergoing the annual condition inspection and will be re-packing the airplane main tire bearings today. I will take pictures of the process and post them here.



  

 

On Sun, Jun 3, 2018 at 9:46 PM, <mike(at)vision499.com (mike(at)vision499.com)> wrote: 	  Quote: 	
		  

Does anybody have a clever idea that will make it easy to jack up and support a TR4 to remove and work on the wheels and brakes etc.

 

I often think I should have made provision for an eyebolt to be screwed into the top of the wing near the wing positioning bolt and then you could just lift it with an engine hoist.

 

I’m crawling underneath the fuselage and cannot see a convenient jacking and support point.

 

My neighbor who has an RV has a clever “goodie” that fits into the axle, I will have a closer look at that and see if I can make something similar.

 

Thanks

 

Mike

 

Mike Pienaar

mike(at)vision499.com (ike(at)vision499.com)

Home: +1 250-999-8121

Mike cell: +1 250-885-0554

1-1100 Tulip Ave, Victoria, BC, V8Z 0A2

 



 



Virus-free. www.avast.com

- The Matronics KIS-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?KIS-List

GalinHdz

Joined: 08 Nov 2017
Posts: 150

Posted: Mon Jun 04, 2018 5:52 pm Post subject: TR$ Jack Options

Use a "low profile" floor jack and you won't have any problems.



FWIW I took photos as I jacked the airplane up in order to repack the main wheel bearings today. I used the photos to do a write up of my procedure and have attached it to this e-mail as a ,pdf file. If you have problems downloading it, I also put a copy on the maintenance section of our web page (www.puertoricoflyer.com). I hope it helps others with this.

On Mon, Jun 4, 2018 at 12:18 PM,  <mike(at)vision499.com (mike(at)vision499.com)> wrote:

 	  Quote: 	
		  

Thanks you very much Galin,

 

I was concerned about damaging the brake and wheel if I tried to jack it on the bottom of the landing gear and would not have thought of resting it on the wing. Thanks for your help

 

Mike

 

From: owner-kis-list-server(at)matronics.com (owner-kis-list-server(at)matronics.com) [mailto:owner-kis-list-server(at)matronics.com (owner-kis-list-server(at)matronics.com)] On Behalf Of Galin Hernandez

Sent: June 4, 2018 6:25 AM

To: kis-list(at)matronics.com (kis-list(at)matronics.com)

Subject: Re: TR$ Jack Options

 

FWIW: I bought a small "low profile" hydraulic 2 ton floor jack. I chock the other wheels so the airplane doesn't shift. I carefully slide the jack under the landing gear metal part far enough so I can lift it up. Once high enough, I slide a slightly modified portable saw horse with a thick movers blanket under the wing then slowly lower the airplane on the sawhorse. Now I can take the floor jack out and work on the tire without fear of it falling off the floor jack. When done, I reverse the process. It works very well and one person can do it easily.

 



I have attached photos of the floor jack and the saw horse so you have an idea of what I am talking about. I am actually undergoing the annual condition inspection and will be re-packing the airplane main tire bearings today. I will take pictures of the process and post them here.



  

 

On Sun, Jun 3, 2018 at 9:46 PM, <mike(at)vision499.com (mike(at)vision499.com)> wrote: 	  Quote: 	
		  

Does anybody have a clever idea that will make it easy to jack up and support a TR4 to remove and work on the wheels and brakes etc.

 

I often think I should have made provision for an eyebolt to be screwed into the top of the wing near the wing positioning bolt and then you could just lift it with an engine hoist.

 

I’m crawling underneath the fuselage and cannot see a convenient jacking and support point.

 

My neighbor who has an RV has a clever “goodie” that fits into the axle, I will have a closer look at that and see if I can make something similar.

 

Thanks

 

Mike

 

Mike Pienaar

mike(at)vision499.com (ike(at)vision499.com)

Home: +1 250-999-8121

Mike cell: +1 250-885-0554

1-1100 Tulip Ave, Victoria, BC, V8Z 0A2

 



 



Virus-free. www.avast.com

- The Matronics KIS-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?KIS-List

Jacking_up_a_KIS4_Wing.pdf

Description:

Download

Filename:

Jacking_up_a_KIS4_Wing.pdf

Filesize:

1.55 MB

Downloaded:

352 Time(s)

Display posts from previous:

	Matronics Email Lists Forum Index -> KIS-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum