Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

alternator gets hot while hangar flying

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> AeroElectric-List
View previous topic :: View next topic  
Author Message
kenryan



Joined: 20 Oct 2009
Posts: 426

PostPosted: Thu Aug 16, 2018 8:07 am    Post subject: alternator gets hot while hangar flying Reply with quote

I've been spending some time in the seat learning to use my Dynon. I just noticed that my alternator (Denso, internally regulated) gets hot with the power on. I can hold my hand against it, but just barely. Any hotter and I would need to remove my hand. I guess it makes sense that it would get hot (energizing the field). Am I harming the alternator? Should I unplug the field wire?

Ken


- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List
Back to top
View user's profile Send private message
nuckolls.bob(at)aeroelect
Guest





PostPosted: Thu Aug 16, 2018 8:25 am    Post subject: alternator gets hot while hangar flying Reply with quote

At 11:06 AM 8/16/2018, you wrote:
Quote:
I've been spending some time in the seat learning to use my Dynon. I just noticed that my alternator (Denso, internally regulated) gets hot with the power on. I can hold my hand against it, but just barely. Any hotter and I would need to remove my hand. I guess it makes sense that it would get hot (energizing the field). Am I harming the alternator? Should I unplug the field wire?

If you have wired it per any of the z-figures, then
you're already configured for battery-only, ground
ops by leaving the DC MASTER switch in BAT only postion
when the engine is not running.

What are you using for alternator control? Can you
not turn it off from the cockpit?


Bob . . .


- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List
Back to top
cluros(at)gmail.com
Guest





PostPosted: Thu Aug 16, 2018 8:28 am    Post subject: alternator gets hot while hangar flying Reply with quote

Could you simply turn the alternator off? Or pull the field breaker?

On Thu, Aug 16, 2018 at 9:06 AM, Ken Ryan <keninalaska(at)gmail.com (keninalaska(at)gmail.com)> wrote:
Quote:
I've been spending some time in the seat learning to use my Dynon. I just noticed that my alternator (Denso, internally regulated) gets hot with the power on. I can hold my hand against it, but just barely. Any hotter and I would need to remove my hand. I guess it makes sense that it would get hot (energizing the field). Am I harming the alternator? Should I unplug the field wire?

Ken



- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List
Back to top
kenryan



Joined: 20 Oct 2009
Posts: 426

PostPosted: Thu Aug 16, 2018 9:07 am    Post subject: alternator gets hot while hangar flying Reply with quote

Bob, no I do not have a BAT only position on my master (drawing attached). Yes, I do have a field breaker that I can easily pull, and I will pull it from now on. Have I harmed my alternator by not turning it off previously?

On Thu, Aug 16, 2018 at 8:32 AM Sebastien <cluros(at)gmail.com (cluros(at)gmail.com)> wrote:

Quote:
Could you simply turn the alternator off? Or pull the field breaker?

On Thu, Aug 16, 2018 at 9:06 AM, Ken Ryan <keninalaska(at)gmail.com (keninalaska(at)gmail.com)> wrote:
Quote:
I've been spending some time in the seat learning to use my Dynon. I just noticed that my alternator (Denso, internally regulated) gets hot with the power on. I can hold my hand against it, but just barely. Any hotter and I would need to remove my hand. I guess it makes sense that it would get hot (energizing the field). Am I harming the alternator? Should I unplug the field wire?

Ken




- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List



electrical.jpg
 Description:
 Filesize:  173.86 KB
 Viewed:  3492 Time(s)

electrical.jpg


Back to top
View user's profile Send private message
echristley(at)att.net
Guest





PostPosted: Thu Aug 16, 2018 9:27 am    Post subject: alternator gets hot while hangar flying Reply with quote

I go out to my Jeep in the summer and parts of it are so hot I can't keep my hands on them. I get in it and drive, and the engine compartment gets even hotter. I shut down, and it gets even hotter. The alternator has lived in there for YEARS and never given me a problem.
If you were able to keep your hand on it, it is probably still wearing its sweater. Smile

On Thursday, August 16, 2018 1:08 PM, Ken Ryan <keninalaska(at)gmail.com> wrote:



Bob, no I do not have a BAT only position on my master (drawing attached). Yes, I do have a field breaker that I can easily pull, and I will pull it from now on. Have I harmed my alternator by not turning it off previously?
On Thu, Aug 16, 2018 at 8:32 AM Sebastien <cluros(at)gmail.com (cluros(at)gmail.com)> wrote:
Quote:
Could you simply turn the alternator off? Or pull the field breaker?
On Thu, Aug 16, 2018 at 9:06 AM, Ken Ryan <keninalaska(at)gmail.com (keninalaska(at)gmail.com)> wrote:
Quote:
I've been spending some time in the seat learning to use my Dynon. I just noticed that my alternator (Denso, internally regulated) gets hot with the power on. I can hold my hand against it, but just barely. Any hotter and I would need to remove my hand. I guess it makes sense that it would get hot (energizing the field). Am I harming the alternator? Should I unplug the field wire?
Ken





- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List
Back to top
nuckolls.bob(at)aeroelect
Guest





PostPosted: Thu Aug 16, 2018 10:58 am    Post subject: alternator gets hot while hangar flying Reply with quote

At 12:05 PM 8/16/2018, you wrote:
Quote:
Bob, no I do not have a BAT only position on my master (drawing attached). Yes, I do have a field breaker that I can easily pull, and I will pull it from now on.

that will work

Quote:
Have I harmed my alternator by not turning it off previously?

No, it will be fine.


Bob . . .


- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List
Back to top
gfarek(at)yahoo.com
Guest





PostPosted: Thu Aug 16, 2018 11:33 am    Post subject: alternator gets hot while hangar flying Reply with quote

Pull the field breaker or fuse maybe.

Sent from my iPhone

On Aug 16, 2018, at 11:18 AM, Sebastien <cluros(at)gmail.com (cluros(at)gmail.com)> wrote:
Quote:
Could you simply turn the alternator off? Or pull the field breaker?

On Thu, Aug 16, 2018 at 9:06 AM, Ken Ryan <keninalaska(at)gmail.com (keninalaska(at)gmail.com)> wrote:
Quote:
I've been spending some time in the seat learning to use my Dynon. I just noticed that my alternator (Denso, internally regulated) gets hot with the power on. I can hold my hand against it, but just barely. Any hotter and I would need to remove my hand. I guess it makes sense that it would get hot (energizing the field). Am I harming the alternator? Should I unplug the field wire?

Ken


=================================== st">http://www.matronics.com/Navigator?AeroElectric-List =================================== cs.com =================================== om =================================== matronics.com/contribution ===================================


- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> AeroElectric-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group