 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
nuckolls.bob(at)aeroelect
Guest
|
 Posted: Mon Dec 30, 2019 8:00 am Post subject: B&C voltage regulator low voltage warning (ADDENDUM) |
 |
|
At 04:03 PM 12/28/2019, you wrote:
| Quote: | --> AeroElectric-List message posted by: "markfw" < (at)icloud.com>
Bob,
I could use two of the RED high intensity bulbs.
I assume you will tell me how to pay. |
shoot me an address
| Quote: | | To finish off another thread, if I have a 40 amp alternator and I want to fuse-protect the B-lead would you recommend a 50 amp (or other) ANL fuse somewhere forward, like on the firewall? |
Mount a MANL40 (miniature ANL)
as close to starter contactor as
practical as illustrated in z-figures.
https://tinyurl.com/sru9gam
There are a number of offerings
for MANL fuseholders. Avoid the
'auto-audio' types that attach
the feedlines by mashing down on
the ends with a setscrew . . .
[img]cid:.0[/img]
Use a two-stud style only with your
feeder terminals in direct contact
with the fuse tabs.
You could make your own out of delrin
or phenolic . . . two bolts and an
assortment of nuts and washers.
Bob . . .
| | - The Matronics AeroElectric-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?AeroElectric-List |
|
| Description: |
|
| Filesize: |
30.05 KB |
| Viewed: |
4384 Time(s) |
|
|
|
| Back to top |
|
 |
nuckolls.bob(at)aeroelect
Guest
|
| Posted: Mon Dec 30, 2019 11:35 am Post subject: B&C voltage regulator low voltage warning (ADDENDUM) |
|
|
At 04:03 PM 12/28/2019, you wrote:
| Quote: | --> AeroElectric-List message posted by: "markfw" < (at)icloud.com>
Bob,
I could use two of the RED high intensity bulbs.
I assume you will tell me how to pay. |
shoot me an address
| Quote: | | To finish off another thread, if I have a 40 amp alternator and I want to fuse-protect the B-lead would you recommend a 50 amp (or other) ANL fuse somewhere forward, like on the firewall? |
Mount a MANL40 (miniature ANL)
as close to starter contactor as
practical as illustrated in z-figures.
https://tinyurl.com/sru9gam
There are a number of offerings
for MANL fuseholders. Avoid the
'auto-audio' types that attach
the feedlines by mashing down on
the ends with a setscrew . . .
[img]cid:.0[/img]
Use a two-stud style only with your
feeder terminals in direct contact
with the fuse tabs.
You could make your own out of delrin
or phenolic . . . two bolts and an
assortment of nuts and washers.
Bob . . .
| | - The Matronics AeroElectric-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?AeroElectric-List |
|
| Description: |
|
| Filesize: |
30.05 KB |
| Viewed: |
4383 Time(s) |
|
|
|
| Back to top |
|
|
nuckolls.bob(at)aeroelect
Guest
|
| Posted: Tue Dec 31, 2019 12:57 pm Post subject: B&C voltage regulator low voltage warning (ADDENDUM) |
|
|
At 11:18 PM 12/30/2019, you wrote:
| Quote: | Deems reports that B&C is recommending a 470 ohm resistor between terminals 3 and 5, but the drawing
http://aeroelectric.com/Pictures/Schematics/LR3_LV_Led_1.jpg
seems to me to show a resistance of more like 940 ohms between the two terminals, ignoring the parallel resistance of the diode.Â
Will either arrangement work? |
I think the image above shows TWO resistors, one
across the lamp, a second in series with the lamp.
This configuration is used when you supply your
own, rudimentary LED (a 4 volt device).
If your proposed LED annunciator already features
a built in series resistor (12v device) then
you use ONE resistor between 3 and 5 on regulator.
Bob . . .
| | - The Matronics AeroElectric-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?AeroElectric-List |
|
|
|
| Back to top |
|
|
nuckolls.bob(at)aeroelect
Guest
|
| Posted: Tue Dec 31, 2019 1:04 pm Post subject: B&C voltage regulator low voltage warning (ADDENDUM) |
|
|
At 11:18 PM 12/30/2019, you wrote:
| Quote: | Deems reports that B&C is recommending a 470 ohm resistor between terminals 3 and 5, but the drawing
http://aeroelectric.com/Pictures/Schematics/LR3_LV_Led_1.jpg
seems to me to show a resistance of more like 940 ohms between the two terminals, ignoring the parallel resistance of the diode.Â
Will either arrangement work? |
I think the image above shows TWO resistors, one
across the lamp, a second in series with the lamp.
This configuration is used when you supply your
own, rudimentary LED (a 4 volt device).
If your proposed LED annunciator already features
a built in series resistor (12v device) then
you use ONE resistor between 3 and 5 on regulator.
Bob . . .
| | - The Matronics AeroElectric-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?AeroElectric-List |
|
|
|
| Back to top |
|
|
nuckolls.bob(at)aeroelect
Guest
|
| Posted: Wed Jan 01, 2020 8:54 am Post subject: B&C voltage regulator low voltage warning (ADDENDUM) |
|
|
At 11:18 PM 12/30/2019, you wrote:
| Quote: | Deems reports that B&C is recommending a 470 ohm resistor between terminals 3 and 5, but the drawing
http://aeroelectric.com/Pictures/Schematics/LR3_LV_Led_1.jpg
seems to me to show a resistance of more like 940 ohms between the two terminals, ignoring the parallel resistance of the diode.Â
Will either arrangement work? |
I think the image above shows TWO resistors, one
across the lamp, a second in series with the lamp.
This configuration is used when you supply your
own, rudimentary LED (a 4 volt device).
If your proposed LED annunciator already features
a built in series resistor (12v device) then
you use ONE resistor between 3 and 5 on regulator.
Bob . . .
| | - The Matronics AeroElectric-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?AeroElectric-List |
|
|
|
| Back to top |
|
|
markfw
Joined: 28 Feb 2019
Posts: 27
Location: Seattle, WA
|
| Posted: Thu Jan 02, 2020 4:59 pm Post subject: Re: B&C voltage regulator low voltage warning (ADDENDU |
|
|
Bob,
thanks for the info about the MANL fuse.
My address is:
1009 Western Ave #1207
Seattle, WA 98104
Mark
| | - The Matronics AeroElectric-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?AeroElectric-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
