 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
Clouddog
Joined: 02 Jun 2016
Posts: 119
Location: Lebanon, TN
|
 Posted: Sat Feb 08, 2020 5:21 am Post subject: Yak-List Digest: 3 Msgs - 02/07/20 |
 |
|
Not knowing what or how the bad mag was tested, is there any chance it's could be the coil on the mag or perhaps the spring that pushes on the contact button at the center of mag? Just thinking out loud.
Greg Wrobel
On Sat, Feb 8, 2020, 01:53 Yak-List Digest Server <yak-list(at)matronics.com (yak-list(at)matronics.com)> wrote:
| Quote: | *
=========================
Online Versions of Today's List Digest Archive
=========================
Today's complete Yak-List Digest can also be found in either of the
two Web Links listed below. The .html file includes the Digest formatted
in HTML for viewing with a web browser and features Hyperlinked Indexes
and Message Navigation. The .txt file includes the plain ASCII version
of the Yak-List Digest and can be viewed with a generic text editor
such as Notepad or with a web browser.
HTML Version:
http://www.matronics.com/digest/digestview.php?Style=82701&View=html&Chapter=2020-02-07&Archive=Yak
Text Version:
http://www.matronics.com/digest/digestview.php?Style=82701&View=txt&Chapter=2020-02-07&Archive=Yak
=======================
EMail Version of Today's List Digest Archive
=======================
----------------------------------------------------------
Yak-List Digest Archive
---
Total Messages Posted Fri 02/07/20: 3
----------------------------------------------------------
Today's Message Index:
----------------------
1. 12:25 PM - Are Huosai magnetos "handed"? (jay-dub)
2. 01:21 PM - Re: Are Huosai magnetos "handed"? (Anthony Savarese)
3. 01:57 PM - Re: Are Huosai magnetos "handed"? (Anthony Savarese)
________________________________ Message 1 _____________________________________
Time: 12:25:03 PM PST US
Subject: Are Huosai magnetos "handed"?
From: "jay-dub" <flyjnw(at)gmail.com (flyjnw(at)gmail.com)>
I've just had mag failure (number 1) and have managed to source a replacement if
necessary. I haven't had chance to diagnose yet so it may just be a short but
if it does require replacement, are Huosai mags handed? As in are mag 1 and
mag 2 the same or different? The answer determines the next steps.
Thanks.
--------
CJ and Yak-52 owner
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=494698#494698
________________________________ Message 2 _____________________________________
Time: 01:21:07 PM PST US
From: Anthony Savarese <dsavarese0812(at)bellsouth.net (dsavarese0812(at)bellsouth.net)>
Subject: Re: Are Huosai magnetos "handed"?
Mags are interchangeable left to right/right to left.
Check the high voltage stick for arcing On the sides. This will cause the mag to
become inop. Do this b4 you replace the entire mag.
Dennis
Sent from my iPhone
> On Feb 7, 2020, at 3:27 PM, jay-dub <flyjnw(at)gmail.com (flyjnw(at)gmail.com)> wrote:
>
>
> I've just had mag failure (number 1) and have managed to source a replacement
if necessary. I haven't had chance to diagnose yet so it may just be a short
but if it does require replacement, are Huosai mags handed? As in are mag 1 and
mag 2 the same or different? The answer determines the next steps.
>
> Thanks.
>
> --------
> CJ and Yak-52 owner
>
>
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=494698#494698
>
>
>
>
>
>
>
>
>
________________________________ Message 3 _____________________________________
Time: 01:57:05 PM PST US
From: Anthony Savarese <dsavarese0812(at)bellsouth.net (dsavarese0812(at)bellsouth.net)>
Subject: Re: Are Huosai magnetos "handed"?
Also make sure the points are opening and closing. If the points dont open, the
mag will be dead.
Dennis
Sent from my iPhone
> On Feb 7, 2020, at 4:22 PM, Anthony Savarese <dsavarese0812(at)bellsouth.net (dsavarese0812(at)bellsouth.net)> wrote:
>
>
> Mags are interchangeable left to right/right to left.
> Check the high voltage stick for arcing On the sides. This will cause the mag
to become inop. Do this b4 you replace the entire mag.
> Dennis
>
>
> Sent from my iPhone
>
>> On Feb 7, 2020, at 3:27 PM, jay-dub <flyjnw(at)gmail.com (flyjnw(at)gmail.com)> wrote:
>>
>>
>> I've just had mag failure (number 1) and have managed to source a replacement
if necessary. I haven't had chance to diagnose yet so it may just be a short
but if it does require replacement, are Huosai mags handed? As in are mag 1 and
mag 2 the same or different? The answer determines the next steps.
>>
>> Thanks.
>>
>> --------
>> CJ and Yak-52 owner
>>
>>
>>
>>
>> Read this topic online here:
>>
>> http://forums.matronics.com/viewtopic.php?p=494698#494698
>>
>>
>>
>>
>>
>>
>>
>>
>>
>
>
>
>
>
===========
br> fts!)
r> > rel="noreferrer noreferrer" target="_blank">http://www.matronics.com/contribution
-Matt Dralle, List Admin.
===========
List" rel="noreferrer noreferrer" target="_blank">http://www.matronics.com/Navigator?Yak-List
===========
FORUMS -
eferrer noreferrer" target="_blank">http://forums.matronics.com
===========
WIKI -
errer noreferrer" target="_blank">http://wiki.matronics.com
===========
b Site -
-Matt Dralle, List Admin.
rel="noreferrer noreferrer" target="_blank">http://www.matronics.com/contribution
===========
|
| | - The Matronics Yak-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Yak-List |
|
|
|
| Back to top |
|
 |
Clouddog
Joined: 02 Jun 2016
Posts: 119
Location: Lebanon, TN
|
| Posted: Sat Feb 08, 2020 5:33 am Post subject: Yak-List Digest: 3 Msgs - 02/07/20 |
|
|
Oops, I said spring pushing on the contact button on the MAG. That's actually located at the center of distributor cap. My Bad. The contact button should move freely to provide constant pressure on the rotor that is on the MAG. Dang I wish I knew what I was talking about sometimes!
Greg Wrobel
On Sat, Feb 8, 2020, 01:53 Yak-List Digest Server <yak-list(at)matronics.com (yak-list(at)matronics.com)> wrote:
| Quote: | *
=========================
Online Versions of Today's List Digest Archive
=========================
Today's complete Yak-List Digest can also be found in either of the
two Web Links listed below. The .html file includes the Digest formatted
in HTML for viewing with a web browser and features Hyperlinked Indexes
and Message Navigation. The .txt file includes the plain ASCII version
of the Yak-List Digest and can be viewed with a generic text editor
such as Notepad or with a web browser.
HTML Version:
http://www.matronics.com/digest/digestview.php?Style=82701&View=html&Chapter=2020-02-07&Archive=Yak
Text Version:
http://www.matronics.com/digest/digestview.php?Style=82701&View=txt&Chapter=2020-02-07&Archive=Yak
=======================
EMail Version of Today's List Digest Archive
=======================
----------------------------------------------------------
Yak-List Digest Archive
---
Total Messages Posted Fri 02/07/20: 3
----------------------------------------------------------
Today's Message Index:
----------------------
1. 12:25 PM - Are Huosai magnetos "handed"? (jay-dub)
2. 01:21 PM - Re: Are Huosai magnetos "handed"? (Anthony Savarese)
3. 01:57 PM - Re: Are Huosai magnetos "handed"? (Anthony Savarese)
________________________________ Message 1 _____________________________________
Time: 12:25:03 PM PST US
Subject: Are Huosai magnetos "handed"?
From: "jay-dub" <flyjnw(at)gmail.com (flyjnw(at)gmail.com)>
I've just had mag failure (number 1) and have managed to source a replacement if
necessary. I haven't had chance to diagnose yet so it may just be a short but
if it does require replacement, are Huosai mags handed? As in are mag 1 and
mag 2 the same or different? The answer determines the next steps.
Thanks.
--------
CJ and Yak-52 owner
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=494698#494698
________________________________ Message 2 _____________________________________
Time: 01:21:07 PM PST US
From: Anthony Savarese <dsavarese0812(at)bellsouth.net (dsavarese0812(at)bellsouth.net)>
Subject: Re: Are Huosai magnetos "handed"?
Mags are interchangeable left to right/right to left.
Check the high voltage stick for arcing On the sides. This will cause the mag to
become inop. Do this b4 you replace the entire mag.
Dennis
Sent from my iPhone
> On Feb 7, 2020, at 3:27 PM, jay-dub <flyjnw(at)gmail.com (flyjnw(at)gmail.com)> wrote:
>
>
> I've just had mag failure (number 1) and have managed to source a replacement
if necessary. I haven't had chance to diagnose yet so it may just be a short
but if it does require replacement, are Huosai mags handed? As in are mag 1 and
mag 2 the same or different? The answer determines the next steps.
>
> Thanks.
>
> --------
> CJ and Yak-52 owner
>
>
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=494698#494698
>
>
>
>
>
>
>
>
>
________________________________ Message 3 _____________________________________
Time: 01:57:05 PM PST US
From: Anthony Savarese <dsavarese0812(at)bellsouth.net (dsavarese0812(at)bellsouth.net)>
Subject: Re: Are Huosai magnetos "handed"?
Also make sure the points are opening and closing. If the points dont open, the
mag will be dead.
Dennis
Sent from my iPhone
> On Feb 7, 2020, at 4:22 PM, Anthony Savarese <dsavarese0812(at)bellsouth.net (dsavarese0812(at)bellsouth.net)> wrote:
>
>
> Mags are interchangeable left to right/right to left.
> Check the high voltage stick for arcing On the sides. This will cause the mag
to become inop. Do this b4 you replace the entire mag.
> Dennis
>
>
> Sent from my iPhone
>
>> On Feb 7, 2020, at 3:27 PM, jay-dub <flyjnw(at)gmail.com (flyjnw(at)gmail.com)> wrote:
>>
>>
>> I've just had mag failure (number 1) and have managed to source a replacement
if necessary. I haven't had chance to diagnose yet so it may just be a short
but if it does require replacement, are Huosai mags handed? As in are mag 1 and
mag 2 the same or different? The answer determines the next steps.
>>
>> Thanks.
>>
>> --------
>> CJ and Yak-52 owner
>>
>>
>>
>>
>> Read this topic online here:
>>
>> http://forums.matronics.com/viewtopic.php?p=494698#494698
>>
>>
>>
>>
>>
>>
>>
>>
>>
>
>
>
>
>
===========
br> fts!)
r> > rel="noreferrer noreferrer" target="_blank">http://www.matronics.com/contribution
-Matt Dralle, List Admin.
===========
List" rel="noreferrer noreferrer" target="_blank">http://www.matronics.com/Navigator?Yak-List
===========
FORUMS -
eferrer noreferrer" target="_blank">http://forums.matronics.com
===========
WIKI -
errer noreferrer" target="_blank">http://wiki.matronics.com
===========
b Site -
-Matt Dralle, List Admin.
rel="noreferrer noreferrer" target="_blank">http://www.matronics.com/contribution
===========
|
| | - The Matronics Yak-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Yak-List |
|
|
|
| Back to top |
|
|
dsavarese0812(at)bellsout
Guest
|
| Posted: Sat Feb 08, 2020 10:08 am Post subject: Yak-List Digest: 3 Msgs - 02/07/20 |
|
|
Anything is possible.Dennis
Sent from my iPhone
| Quote: | On Feb 8, 2020, at 8:23 AM, Greg Wrobel <clouddog22(at)gmail.com> wrote:
Not knowing what or how the bad mag was tested, is there any chance it's could be the coil on the mag or perhaps the spring that pushes on the contact button at the center of mag? Just thinking out loud.
Greg Wrobel
On Sat, Feb 8, 2020, 01:53 Yak-List Digest Server <yak-list(at)matronics.com (yak-list(at)matronics.com)> wrote:
| Quote: | *
=========================
Online Versions of Today's List Digest Archive
=========================
Today's complete Yak-List Digest can also be found in either of the
two Web Links listed below. The .html file includes the Digest formatted
in HTML for viewing with a web browser and features Hyperlinked Indexes
and Message Navigation. The .txt file includes the plain ASCII version
of the Yak-List Digest and can be viewed with a generic text editor
such as Notepad or with a web browser.
HTML Version:
http://www.matronics.com/digest/digestview.php?Style=82701&View=html&Chapter=2020-02-07&Archive=Yak
Text Version:
http://www.matronics.com/digest/digestview.php?Style=82701&View=txt&Chapter=2020-02-07&Archive=Yak
=======================
EMail Version of Today's List Digest Archive
=======================
----------------------------------------------------------
Yak-List Digest Archive
---
Total Messages Posted Fri 02/07/20: 3
----------------------------------------------------------
Today's Message Index:
----------------------
1. 12:25 PM - Are Huosai magnetos "handed"? (jay-dub)
2. 01:21 PM - Re: Are Huosai magnetos "handed"? (Anthony Savarese)
3. 01:57 PM - Re: Are Huosai magnetos "handed"? (Anthony Savarese)
________________________________ Message 1 _____________________________________
Time: 12:25:03 PM PST US
Subject: Are Huosai magnetos "handed"?
From: "jay-dub" <flyjnw(at)gmail.com (flyjnw(at)gmail.com)>
I've just had mag failure (number 1) and have managed to source a replacement if
necessary. I haven't had chance to diagnose yet so it may just be a short but
if it does require replacement, are Huosai mags handed? As in are mag 1 and
mag 2 the same or different? The answer determines the next steps.
Thanks.
--------
CJ and Yak-52 owner
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=494698#494698
________________________________ Message 2 _____________________________________
Time: 01:21:07 PM PST US
From: Anthony Savarese <dsavarese0812(at)bellsouth.net (dsavarese0812(at)bellsouth.net)>
Subject: Re: Are Huosai magnetos "handed"?
Mags are interchangeable left to right/right to left.
Check the high voltage stick for arcing On the sides. This will cause the mag to
become inop. Do this b4 you replace the entire mag.
Dennis
Sent from my iPhone
> On Feb 7, 2020, at 3:27 PM, jay-dub <flyjnw(at)gmail.com (flyjnw(at)gmail.com)> wrote:
>
>
> I've just had mag failure (number 1) and have managed to source a replacement
if necessary. I haven't had chance to diagnose yet so it may just be a short
but if it does require replacement, are Huosai mags handed? As in are mag 1 and
mag 2 the same or different? The answer determines the next steps.
>
> Thanks.
>
> --------
> CJ and Yak-52 owner
>
>
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=494698#494698
>
>
>
>
>
>
>
>
>
________________________________ Message 3 _____________________________________
Time: 01:57:05 PM PST US
From: Anthony Savarese <dsavarese0812(at)bellsouth.net (dsavarese0812(at)bellsouth.net)>
Subject: Re: Are Huosai magnetos "handed"?
Also make sure the points are opening and closing. If the points dont open, the
mag will be dead.
Dennis
Sent from my iPhone
> On Feb 7, 2020, at 4:22 PM, Anthony Savarese <dsavarese0812(at)bellsouth.net (dsavarese0812(at)bellsouth.net)> wrote:
>
>
> Mags are interchangeable left to right/right to left.
> Check the high voltage stick for arcing On the sides. This will cause the mag
to become inop. Do this b4 you replace the entire mag.
> Dennis
>
>
> Sent from my iPhone
>
>> On Feb 7, 2020, at 3:27 PM, jay-dub <flyjnw(at)gmail.com (flyjnw(at)gmail.com)> wrote:
>>
>>
>> I've just had mag failure (number 1) and have managed to source a replacement
if necessary. I haven't had chance to diagnose yet so it may just be a short
but if it does require replacement, are Huosai mags handed? As in are mag 1 and
mag 2 the same or different? The answer determines the next steps.
>>
>> Thanks.
>>
>> --------
>> CJ and Yak-52 owner
>>
>>
>>
>>
>> Read this topic online here:
>>
>> http://forums.matronics.com/viewtopic.php?p=494698#494698
>>
>>
>>
>>
>>
>>
>>
>>
>>
>
>
>
>
>
===========
br> fts!)
r> > rel="noreferrer noreferrer" target="_blank">http://www.matronics.com/contribution
-Matt Dralle, List Admin.
===========
List" rel="noreferrer noreferrer" target="_blank">http://www.matronics.com/Navigator?Yak-List
===========
FORUMS -
eferrer noreferrer" target="_blank">http://forums.matronics.com
===========
WIKI -
errer noreferrer" target="_blank">http://wiki.matronics.com
===========
b Site -
-Matt Dralle, List Admin.
rel="noreferrer noreferrer" target="_blank">http://www.matronics.com/contribution
===========
|
|
| | - The Matronics Yak-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Yak-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
