Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Instrument Panel Advice re placement on Firewall options

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Europa-List
View previous topic :: View next topic  
Author Message
Duncan McFadyean



Joined: 18 Jan 2011
Posts: 219

PostPosted: Thu Apr 23, 2020 2:28 am    Post subject: Instrument Panel Advice re placement on Firewall options Reply with quote

Tony,
Personally I would not bother. The standard instrument panel is quite flexible anyway, to the extent that a g-meter installed in mine gets 'flicked' to stupidly high readings on a hard landing as the panel rebounds elastically. A resilient foam gasket under the panel mounting flange may provide some useful damping.

Duncan Mcf.
Quote:
On 23 April 2020 at 06:21 Tony Renshaw <tonyrenshaw268(at)gmail.com> wrote:




Gidday,
I have my instrument panel such that it sits on small rubber mounts, the type that is a 1/2 wide rubber mount with a flat washer either side, which have centrally located threaded 1/4” shanks out each side. These ones are pretty hard though, hard to tell if they would do much. With these in place my panel will be suspended on them, and sit somewhat on a small soft rubber pad on top of my tunnel. I am wondering if I should be bothered, whether I should ditch this idea and mount the panel to the firewall directly like I believe the instructions dictate. I’m keen on knowing what people think of attempts to isolate the high frequency vibration, whether it's worth the effort. I am going to have an electronic panel as best as I can, and my sub panels screw straight onto lugs on my panel carcass. I’ve also been advised to cut the lip off the top of the panel which I have addressed by building an inverted, internal flange, so I can do this, but other than weight saving I’m w!
ondering if that is a common thing to do. It wouldn’t hurt to put my panel forward an extra 1/2” but it’s not an imperative, and I do already have the mounts attached to the firewall, albeit with nylocs on the engine side, to be changed for conventional nuts before I go too far and forget.
Any tips gratefully accepted.
Regards
Tony Renshaw







- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
View user's profile Send private message
rowlandcarson(at)gmail.co
Guest





PostPosted: Fri Apr 24, 2020 2:51 am    Post subject: Instrument Panel Advice re placement on Firewall options Reply with quote

On 2020-04-23, at 06:21, Tony Renshaw <tonyrenshaw268(at)gmail.com> wrote:

Quote:
I have my instrument panel such that it sits on small rubber mounts


Quote:
I’ve also been advised to cut the lip off the top of the panel which I have addressed by building an inverted, internal flange, so I can do this, but other than weight saving I’m wondering if that is a common thing to do


Tony - I think it probably is common, although perhaps not much reported. Here is a link to a picture of my instrument module (F14) with a flange similar to what you describe:

http://www.rowlandcarson.org.uk/aviation/europa_435/im_inner_flange.php

Although I have now discarded the mechanical gyros I originally intended to fit:

http://www.rowlandcarson.org.uk/aviation/europa_435/subpanel.php

I am retaining the anti-vibration bushes on which the main aluminium panel is mounted. I feel that the mechanical movements of the ASI, altimeter & VSI would probably live a bit longer with some vibration damping. Here is a link to a picture of the unpopulated aluminium panels:

http://www.rowlandcarson.org.uk/aviation/europa_435/laser_etching.php

in friendship

Rowland

| Rowland Carson ... that's Rowland with a 'w' ...
| <rowlandcarson(at)gmail.com> http://www.rowlandcarson.org.uk
| Skype, Twitter: rowland_carson Facebook: Rowland Carson


- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Europa-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group