Matronics Email Lists :: View topic - Butt Splice on Main Alt B Lead

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

Butt Splice on Main Alt B Lead

Matronics Email Lists Forum Index -> AeroElectric-List

View previous topic :: View next topic

Author Message

david(at)carter.net
Guest

Posted: Fri Sep 25, 2020 6:58 am Post subject: Butt Splice on Main Alt B Lead

A couple of questionsÂ on this connection. Z101 calls for a 12-gauge FLW butt spliced onto the 10-gauge main alt B-lead wire.Â 



I didn't see any this large at Spruce, but it appears that both Amazon & AutoZone have the Dorman splices in 8 gauge. Is this a satsifactoryÂ product for our needs?Â 

https://www.autozone.com/miscellaneous-non-automotive/electrical-wire-connector/dorman-conduct-tite-8-gauge-butt-connectors/422502_0_0

Also, are there any special techniques required to ensure that the smaller wire is propertlyÂ gripped in the slice when crimped? Do I need to put some extra wire strands in there to fill the connector & snip off any excess?Â 

Thanks!

David





---

David Carter

david(at)carter.net (david(at)carter.net)

jluckey(at)pacbell.net
Guest

Posted: Fri Sep 25, 2020 8:04 am Post subject: Butt Splice on Main Alt B Lead

David,

I classify those kind of connectors as "cheap automotive" wire terminals and would not recommend them for use is aircraft.

Do a search for AMP (is Manufacturer) PIDG (Pre Insulated Diamond Grip) butt splice for something that looks like this:

[img]cid:3c50c1ed-d948-e161-0bcd-39a0b1f17789(at)yahoo.com[/img]">





Jeff Luckey

                  

                                                                    On Friday, September 25, 2020, 08:48:29 AM PDT, David Carter <david(at)carter.net> wrote:                 

                 



                 



                 A couple of questions on this connection. Z101 calls for a 12-gauge FLW butt spliced onto the 10-gauge main alt B-lead wire. 



I didn't see any this large at Spruce, but it appears that both Amazon & AutoZone have the Dorman splices in 8 gauge. Is this a satsifactory product for our needs? 

https://www.autozone.com/miscellaneous-non-automotive/electrical-wire-connector/dorman-conduct-tite-8-gauge-butt-connectors/422502_0_0

Also, are there any special techniques required to ensure that the smaller wire is propertly gripped in the slice when crimped? Do I need to put some extra wire strands in there to fill the connector & snip off any excess? 

Thanks!

David





---

David Carter

david(at)carter.net (david(at)carter.net)

1601049505722blob.jpg

Description:

Filesize:

117.99 KB

Viewed:

3699 Time(s)

nuckolls.bob(at)aeroelect
Guest

Posted: Fri Sep 25, 2020 8:22 am Post subject: Butt Splice on Main Alt B Lead

At 09:56 AM 9/25/2020, you wrote:

  	  Quote: 	
		  A couple of questions on this connection. Z101 calls for a 12-gauge FLW butt spliced onto the 10-gauge main alt B-lead wire.Â 	


   There should be a 4AWG spread between the protected feeder

   and the fusible link stock. So the 10AWG feeder from the aux

   alternator gets a 14AWG FLW. That's the case in the

   last iteration of Z101 (rev B).

  	  Quote: 	
		   



 I didn't see any this large at Spruce, but it appears that both Amazon & AutoZone have the Dorman splices in 8 gauge. Is this a satsifactoryÂ product for our needs?Â 

  https://www.autozone.com/miscellaneous-non-automotive/electrical-wire-connector/dorman-conduct-tite-8-gauge-butt-connectors/422502_0_0 	


   The 'yellow' series PIDG terminals are indicated

   for 10-12AWG wires.



  https://tinyurl.com/y4njsbmt



   This splice would work with our favorite po' boy's

   crimp tool.



   Keep in mind that 'gas tightness' of the interface

   between wire and splice is the holy-grail. Folks

   like AMP, Molex, C-H, have spent untold bux researching

   and qualifying proven combinations of crimp dies, terminals

   and wire stranding to achieve those goals.



   Now comes wire, terminals and tools from a variety of

   sources NOT tested for playing nice in the same

   sandbox. Here are some references from the

   'Connection



  https://tinyurl.com/kfk6jss



   http://aeroelectric.com/articles/terminal.pdf



   Field history on this series of tools with PIDG has

   been favorable



  https://tinyurl.com/yy6wlbv2



 

 You might look into this alternative. The heat-shrink

 terminals and butt splices have been around for awhile



  https://tinyurl.com/y26la2p6



 . . . but no tools that produced a elegant upset of the

 wire grips without mangling the insulation . . . until

 now.



  https://tinyurl.com/y3kzobsx



 I'm ordering one of these in to take a look and try

 it out.



 

  	  Quote: 	
		  Also, are there any special techniques required to ensure that the smaller wire is propertlyÂ gripped in the slice when crimped? Do I need to put some extra wire strands in there to fill the connector & snip off any excess? 	


   You betcha. Strip the 14AWG wire back about 1/2

   and fold it so as to double the strands

   in the wire grip.



   Alternatively, you could consider a soldered lap

   joint like this



  https://tinyurl.com/yxq7c5d9



   BUT NO MATER WHICH TECHNIQUE YOU CHOSE TO EXPLORE,

   BUY EXTRA TERMINALS AND EXPERIMENT WITH THE

   PROPOSED TOOL(S) AND WIRE. DO A PULL TEST TO INSURE

   THAT YOUR WIRE/TOOL/TERMINAL COMBINATIONS ARE

   COMING TOGETHER IN BLISSFUL EMBRACE.



 

   Bob . . .

david(at)carter.net
Guest

Posted: Fri Sep 25, 2020 8:46 am Post subject: Butt Splice on Main Alt B Lead

I made a mistake in my question.Â  The main alt Â  lead is 8 gauge & joins to a 12 gauge fusible link.Â  That's the size butt connector I'm not seeing at Spruce.Â  The yellow amp goes up to 10. Â 



On Fri, Sep 25, 2020 at 12:25 PM Robert L. Nuckolls, III <nuckolls.bob(at)aeroelectric.com (nuckolls.bob(at)aeroelectric.com)> wrote:



 	  Quote: 	
		  



At 09:56 AM 9/25/2020, you wrote:

 	  Quote: 	
		  A couple of questions on this



connection. Z101 calls for a 12-gauge FLW butt spliced onto the 10-gauge



main alt B-lead wire.Ã‚ 	


Â  There should be a 4AWG spread between the protected feeder

Â  and the fusible link stock. So the 10AWG feeder from the aux

Â  alternator gets a 14AWG FLW. That's the case in the

Â  last iteration of Z101 (rev B).

 	  Quote: 	
		  Â 



I didn't see any this large at Spruce, but it appears that both Amazon



& AutoZone have the Dorman splices in 8 gauge. Is this a



satsifactoryÃ‚ product for our needs?Ã‚ 





https://www.autozone.com/miscellaneous-non-automotive/electrical-wire-connector/dorman-conduct-tite-8-gauge-butt-connectors/422502_0_0



	


Â  The 'yellow' series PIDG terminals are indicated

Â  for 10-12AWG wires.



https://tinyurl.com/y4njsbmt



Â  This splice would work with our favorite po' boy's

Â  crimp tool.



Â  Keep in mind that 'gas tightness' of the interface

Â  between wire and splice is the holy-grail. Folks

Â  like AMP, Molex, C-H, have spent untold bux researching

Â  and qualifying proven combinations of crimp dies, terminals

Â  and wire stranding to achieve those goals.



Â  Now comes wire, terminals and tools from a variety of

Â  sources NOT tested for playing nice in the same

Â  sandbox. Here are some references from the

Â  'Connection



https://tinyurl.com/kfk6jss



http://aeroelectric.com/articles/terminal.pdf



Â  Field history on this series of tools with PIDG has

Â  been favorable



https://tinyurl.com/yy6wlbv2

You might look into this alternative. The heat-shrink

terminals and butt splices have been around for awhile



https://tinyurl.com/y26la2p6



. . . but no tools that produced a elegant upset of the

wire grips without mangling the insulation . . . until

now.



https://tinyurl.com/y3kzobsx



I'm ordering one of these in to take a look and try

it out.

 	  Quote: 	
		  Also, are there any special



techniques required to ensure that the smaller wire is propertlyÃ‚ gripped



in the slice when crimped? Do I need to put some extra wire strands in



there to fill the connector & snip off any excess? 	


Â  You betcha. Strip the 14AWG wire back about 1/2

Â  and fold it so as to double the strands

Â  in the wire grip.



Â  Alternatively, you could consider a soldered lap

Â  joint like this



https://tinyurl.com/yxq7c5d9



Â  BUT NO MATER WHICH TECHNIQUE YOU CHOSE TO EXPLORE,

Â  BUY EXTRA TERMINALS AND EXPERIMENT WITH THE

Â  PROPOSED TOOL(S) AND WIRE. DO A PULL TEST TO INSURE

Â  THAT YOUR WIRE/TOOL/TERMINAL COMBINATIONS ARE

Â  COMING TOGETHER IN BLISSFUL EMBRACE.









Â  Bob . . .





	




-- 

---

David Carter

david(at)carter.net (david(at)carter.net)

Flyitnow

Joined: 05 Aug 2016
Posts: 4

Posted: Fri Sep 25, 2020 8:52 am Post subject: Butt Splice on Main Alt B Lead

Aircraft Spruce # 320570

                  

                                                                    On Friday, September 25, 2020, 09:34:01 AM PDT, Jeff Luckey <jluckey(at)pacbell.net> wrote:                 

                 



                 



                 

         David,



I classify those kind of connectors as "cheap automotive" wire terminals and would not recommend them for use is aircraft.



Do a search for AMP (is Manufacturer) PIDG (Pre Insulated Diamond Grip) butt splice for something that looks like this:



[img]cid:QnZ7yPtZMT5FlqyPCsTE[/img]">



Jeff Luckey



                  

                                                                    On Friday, September 25, 2020, 08:48:29 AM PDT, David Carter <david(at)carter.net> wrote:                 

                 

                 

                 A couple of questions on this connection. Z101 calls for a 12-gauge FLW butt spliced onto the 10-gauge main alt B-lead wire. 

I didn't see any this large at Spruce, but it appears that both Amazon & AutoZone have the Dorman splices in 8 gauge. Is this a satsifactory product for our needs? 

https://www.autozone.com/miscellaneous-non-automotive/electrical-wire-connector/dorman-conduct-tite-8-gauge-butt-connectors/422502_0_0



Also, are there any special techniques required to ensure that the smaller wire is propertly gripped in the slice when crimped? Do I need to put some extra wire strands in there to fill the connector & snip off any excess? 



Thanks!

David

---David Carterdavid(at)carter.net (david(at)carter.net)

1601049505722blob.jpg

Description:

Filesize:

117.99 KB

Viewed:

3698 Time(s)

Mauledriver(at)nc.rr.com
Guest

Posted: Fri Sep 25, 2020 9:03 am Post subject: Butt Splice on Main Alt B Lead

You would need crimping equipment of       the right size in order to use a crimp type splice.Â  Even assuming       a quality connector is available, doing it once or twice may not       justify getting the crimping equipment required or gaining the       practice needed to do it 100% effectively.

     

     

     I'd suggest a solder type butt       connector sized for 10guage and then stuffing the 12 guage side       with extra strands as required.Â  All you need is solder and a       torch to get it done.Â  Big item like that is easier technique-wise       than smaller solder work.

     

     

     Bill "just a another amateur wire       splicer with an opinion" Watson

     

     

     

     On 9/25/2020 10:56 AM, David Carter       wrote:

     

      	  Quote: 	
		                A couple of questionsÂ on this connection. Z101         calls for a 12-gauge FLW butt spliced onto the 10-gauge main alt         B-lead wire.Â          

         

         I didn't see any this large at Spruce, but it appears that           both Amazon & AutoZone have the Dorman splices in 8 gauge.           Is this a satsifactoryÂ product for our needs?Â 

         https://www.autozone.com/miscellaneous-non-automotive/electrical-wire-connector/dorman-conduct-tite-8-gauge-butt-connectors/422502_0_0

         

         

         Also, are there any special techniques required to ensure           that the smaller wire is propertlyÂ gripped in the slice when           crimped? Do I need to put some extra wire strands in there to           fill the connector & snip off any excess?Â 

         

         

         Thanks!

         David

         

         

         

         

                                 ---

               David Carter

               david(at)carter.net (david(at)carter.net)

           

         

       

     	
     



            	 		 			 				 			 		 		 			

 				This email has been checked for viruses by Avast antivirus software. 				

www.avast.com 			 		 	   [url=#DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2] [/url]

jluckey(at)pacbell.net
Guest

Posted: Fri Sep 25, 2020 11:15 am Post subject: Butt Splice on Main Alt B Lead

David,

See if this meets your needs....

Heat Shrink, Crimp Seal Butt Connectors



<![endif]--><![endif]-->$7.73

<![endif]-->Heat Shrink, Crimp Seal Butt Connectors

Heat Shrink, Crimp Seal Butt Connectors

                  

                                                                    On Friday, September 25, 2020, 10:38:51 AM PDT, David Carter <david(at)carter.net> wrote:                 

                 



                 



                 I made a mistake in my question.  The main alt   lead is 8 gauge & joins to a 12 gauge fusible link.  That's the size butt connector I'm not seeing at Spruce.  The yellow amp goes up to 10.  

On Fri, Sep 25, 2020 at 12:25 PM Robert L. Nuckolls, III <nuckolls.bob(at)aeroelectric.com (nuckolls.bob(at)aeroelectric.com)> wrote:

 	  Quote: 	
		  At 09:56 AM 9/25/2020, you wrote: 	  Quote: 	
		  A couple of questions on thisconnection. Z101 calls for a 12-gauge FLW butt spliced onto the 10-gaugemain alt B-lead wire.Ã‚ 	
  There should be a 4AWG spread between the protected feeder  and the fusible link stock. So the 10AWG feeder from the aux  alternator gets a 14AWG FLW. That's the case in the  last iteration of Z101 (rev B). 	  Quote: 	
		   I didn't see any this large at Spruce, but it appears that both Amazon& AutoZone have the Dorman splices in 8 gauge. Is this asatsifactoryÃ‚ product for our needs?Ã‚ https://www.autozone.com/miscellaneous-non-automotive/electrical-wire-connector/dorman-conduct-tite-8-gauge-butt-connectors/422502_0_0 	
  The 'yellow' series PIDG terminals are indicated  for 10-12AWG wires.https://tinyurl.com/y4njsbmt  This splice would work with our favorite po' boy's  crimp tool.  Keep in mind that 'gas tightness' of the interface  between wire and splice is the holy-grail. Folks  like AMP, Molex, C-H, have spent untold bux researching  and qualifying proven combinations of crimp dies, terminals  and wire stranding to achieve those goals.  Now comes wire, terminals and tools from a variety of  sources NOT tested for playing nice in the same  sandbox. Here are some references from the  'Connectionhttps://tinyurl.com/kfk6jsshttp://aeroelectric.com/articles/terminal.pdf  Field history on this series of tools with PIDG has  been favorablehttps://tinyurl.com/yy6wlbv2You might look into this alternative. The heat-shrinkterminals and butt splices have been around for awhilehttps://tinyurl.com/y26la2p6. . . but no tools that produced a elegant upset of thewire grips without mangling the insulation . . . untilnow.https://tinyurl.com/y3kzobsxI'm ordering one of these in to take a look and tryit out. 	  Quote: 	
		  Also, are there any specialtechniques required to ensure that the smaller wire is propertlyÃ‚ grippedin the slice when crimped? Do I need to put some extra wire strands inthere to fill the connector & snip off any excess? 	
  You betcha. Strip the 14AWG wire back about 1/2  and fold it so as to double the strands  in the wire grip.  Alternatively, you could consider a soldered lap  joint like thishttps://tinyurl.com/yxq7c5d9  BUT NO MATER WHICH TECHNIQUE YOU CHOSE TO EXPLORE,  BUY EXTRA TERMINALS AND EXPERIMENT WITH THE  PROPOSED TOOL(S) AND WIRE. DO A PULL TEST TO INSURE  THAT YOUR WIRE/TOOL/TERMINAL COMBINATIONS ARE  COMING TOGETHER IN BLISSFUL EMBRACE.

  Bob . . .

	


-- ---David Carterdavid(at)carter.net (david(at)carter.net)

nuckolls.bob(at)aeroelect
Guest

Posted: Fri Sep 25, 2020 11:31 am Post subject: Butt Splice on Main Alt B Lead

At 11:41 AM 9/25/2020, you wrote:

  	  Quote: 	
		  I made a mistake in my question.Â  The main alt Â  lead is 8 gauge & joins to a 12 gauge fusible link.Â

 That's the size butt connector I'm not seeing at Spruce.Â  The yellow amp goes up to 10. Â 	


  Crimp tools in that size are not commonly

  available. I think I'd go for a soldered lap-joint

  for that one.



 

   Bob . . .

david(at)carter.net
Guest

Posted: Fri Sep 25, 2020 1:03 pm Post subject: Butt Splice on Main Alt B Lead

Yes, I was leaning toward the soldered lap joint approach. I considered crimping ring terminals on each wire end & joining them with a 1/4" bolt/nut assembly, but the 8-gauge crimper again becomes a problem.Â 



Thanks to all for the advice & ideas.Â 

---

David Carter

david(at)carter.net (david(at)carter.net)



On Fri, Sep 25, 2020 at 3:37 PM Robert L. Nuckolls, III <nuckolls.bob(at)aeroelectric.com (nuckolls.bob(at)aeroelectric.com)> wrote:



 	  Quote: 	
		    At 11:41 AM 9/25/2020, you wrote:

  	  Quote: 	
		  I made a mistake in my question.Ã‚Â  The main alt Ã‚Â  lead is 8 gauge & joins to a 12 gauge fusible link.Ã‚

 That's the size butt connector I'm not seeing at Spruce.Ã‚Â  The yellow amp goes up to 10. Ã‚ 	


 Â Crimp tools in that size are not commonly

 Â available. I think I'd go for a soldered lap-joint

 Â for that one.



 

 Â  Bob . . .

DougW

Joined: 16 Sep 2015
Posts: 14
Location: Washington

Posted: Fri Sep 25, 2020 3:50 pm Post subject: Butt Splice on Main Alt B Lead

Don’t know if these butt connectors would be of use here, but I am curious what Bob thinks.  This URL goes to a Summit Racing site and shows that application.  Looks pretty slick to me.

 

https://tinyurl.com/y374wd4m

 

Doug Windhorn

 

From: owner-aeroelectric-list-server(at)matronics.com <owner-aeroelectric-list-server(at)matronics.com> On Behalf Of Robert L. Nuckolls, III

Sent: Friday, September 25, 2020 10:02 AM

To: aeroelectric-list(at)matronics.com

Subject: Re: Butt Splice on Main Alt B Lead

 

At 11:41 AM 9/25/2020, you wrote:



 	  Quote: 	
		  

I made a mistake in my question.Â  The main alt Â  lead is 8 gauge & joins to a 12 gauge fusible link.Â

That's the size butt connector I'm not seeing at Spruce.Â  The yellow amp goes up to 10. Â 	




 Crimp tools in that size are not commonly

 available. I think I'd go for a soldered lap-joint

 for that one.



  Bob . . .

Display posts from previous:

	Matronics Email Lists Forum Index -> AeroElectric-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum