Matronics Email Lists :: View topic - strange A/H nuts & generator brushes?

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

strange A/H nuts & generator brushes?

Matronics Email Lists Forum Index -> Yak-List

View previous topic :: View next topic

Author Message

draftsjust417(at)gmail.co
Guest

Posted: Sun Dec 20, 2020 7:01 pm Post subject: strange A/H nuts & generator brushes?

Hello Nanchangers-

Looking ahead to 2021 maintenance on my CJ6, I'm prowling for (4) of the "special nuts" used on the Chinese BDP-2 artificial horizon.

The parts catalog calls them p/n 167-43 (ref vol.5, figure 2-7-1, item #12.)

Also, the associated p/n 4C12.13.d5 washers, item #11.



See pix...

Also, anyone have a lead on the brushes for the big Chinese generator?

Ref p/n ZP4.

Doug?



I'm doing my best to keep everything stock PLAAF, without too many upgrades to Western equipment.

Thanks-

I hope everyone is the midst of a Merry Christmas and happy holiday season-

Justin

N280NC

- The Matronics Yak-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Yak-List

Art_Horizon,_parts_catalog.jpg

Description:

Filesize:

217.24 KB

Viewed:

2343 Time(s)

Art_Horiz,_special_nuts.jpg

Description:

Filesize:

200.18 KB

Viewed:

2343 Time(s)

AlaskaChang801

Joined: 26 Jan 2018
Posts: 36

Posted: Sat Dec 26, 2020 5:23 pm Post subject: Re: strange A/H nuts & generator brushes?

I just replaced my back AI and mine had 4mm nut and washer combo from the previous owner as the plate wasn't the stock one. Anyway, I understand the desire to keep the look stock etc, but if you can't get these from Doug Sapp, then you might have to buy alternative ones from MacMaster-Carr. They have M4 cap nuts, but not sure of the depth of thread so you may have to add a couple flat washers to take up the thickness if they bottom out in the cap. Or just buy 4mm Nylok nuts and go that way.

- The Matronics Yak-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Yak-List

draftsjust417(at)gmail.co
Guest

Posted: Sat Dec 26, 2020 7:52 pm Post subject: strange A/H nuts & generator brushes?

Ya... that's a good plan-B.

Great to not be in a rush or AOG...

Thanks!

Justin

On Sun, Dec 27, 2020 at 5:59 AM AlaskaChang801 <themilnes95(at)gmail.com (themilnes95(at)gmail.com)> wrote:



 	  Quote: 	
		  --> Yak-List message posted by: "AlaskaChang801" <themilnes95(at)gmail.com (themilnes95(at)gmail.com)>

 

 I just replaced my back AI and mine had 4mm nut and washer combo from the previous owner as the plate wasn't the stock one. Anyway, I understand the desire to keep the look stock etc, but if you can't get these from Doug Sapp, then you might have to buy alternative ones from MacMaster-Carr. They have M4 cap nuts, but not sure of the depth of thread so you may have to add a couple flat washers to take up the thickness if they bottom out in the cap. Or just buy 4mm Nylok nuts and go that way.

 

 

 

 

 Read this topic online here:

 

 http://forums.matronics.com/viewtopic.php?p=499821#499821

 

 

 

 

 

 

 ===========

 List" rel="noreferrer" target="_blank">http://www.matronics.com/Navigator?Yak-List

 ===========

  FORUMS -

 eferrer" target="_blank">http://forums.matronics.com

 ===========

 WIKI -

 errer" target="_blank">http://wiki.matronics.com

 ===========

 b Site -

           -Matt Dralle, List Admin.

 rel="noreferrer" target="_blank">http://www.matronics.com/contribution

 ===========

- The Matronics Yak-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Yak-List

Display posts from previous:

	Matronics Email Lists Forum Index -> Yak-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum