Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Cold air plenum K&N filter replacement

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Europa-List
View previous topic :: View next topic  
Author Message
budyerly@msn.com



Joined: 05 Oct 2019
Posts: 286
Location: Florida USA

PostPosted: Thu Nov 25, 2021 10:48 am    Post subject: Cold air plenum K&N filter replacement Reply with quote

Chris:
Thirty minutes on the K&N site showed the following:
Original 912/912S Air Filter is a lifetime K&N Filter Number 33-2564 (1989-1994 FORD (Fiesta, Fiesta III)
Air Filter Length (in.):7.75 in. Air Filter Width (in.):5.81 in. Air Filter Height (in.):1.13 in.

Substitute: K&N 33-2736 (Height:1.188”(30 mm),Outside Length:7.781”(198 mm),Width: 5.938”(151 mm)
You will have to file or sand a bit as it appears slightly larger than the previous. Consequences of getting old.

The washable K&N 332564 will either be replaced by an alternate Ford Fiesta part or slightly widen your existing airbox and install the substitute 95/96 Ford Fiesta III part 33-2736.
While others may be looking at this thread, consider a water diverter for the 912S stock cowl to divert heavy rain entering your carb airbox while parked or build a complete water tight intake block as others have done.
I prefer a plane cover, but it is not convenient for most traveling cross country. This is a Band-Aid work around.

Happy Thanksgiving,
Bud Yerly



--


- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List



Airbox_water_intrusion_in_the_carb_box.pdf
 Description:

Download
 Filename:  Airbox_water_intrusion_in_the_carb_box.pdf
 Filesize:  763.24 KB
 Downloaded:  121 Time(s)

Back to top
View user's profile Send private message Send e-mail Visit poster's website
JohnFrance



Joined: 17 Sep 2014
Posts: 78
Location: Grenoble France

PostPosted: Fri Nov 26, 2021 2:51 am    Post subject: Re: Cold air plenum K&N filter replacement Reply with quote

Hi All,
I have also looked into this and after ordering and paying for a K&N filter and being told that its out of stock! I looked for a replacement.

Green Filter, make air filters for performance vehicles as well as Ford Fiesta's.
They use a cloth as a filter material rather than gauze and are reputedly very durable.
I have only read good things about them so here is the model required for a Europa as it's not listed in their reference table! It may be a tad too wide according to the dimensions they provide and is a little less in height.

FORD FIESTA III 1,8L TD 77 57 RFL >94 PANEL 197 ── 149 ── ── ── 23 1 Reference Nr P360270

https://www.green-filter.com/en/shop__trashed/voiture/2995en/

I'm not recommending this product but I am going to give it a try as the K&N model seems hard to find.
Cheers

John


- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List

_________________
Europa mono Nr 192
Back to top
View user's profile Send private message Send e-mail
n7188u



Joined: 15 Nov 2015
Posts: 404

PostPosted: Sat Nov 27, 2021 3:45 am    Post subject: Re: Cold air plenum K&N filter replacement Reply with quote

Thanks Bud and John.

Apologies for not replying earlier. Thanksgiving morning I flew to a grass field nearby and when I went ahead to takeoff found that the engine was only developing 4000 RPM (relatively smoothly). Aborted takeoff and two days of troubleshooting later discovered that the diaphragm on the port carb was shot. Luckily found someone with a spare and was able to get back home safely yesterday. It was not easy to find the culprit and had some Rotax savvy friends baffled. A check with analog carb balance gages finally pointed to the root cause.

It’s true that my engine sat in its crate after overhaul for three years and flown since March but never imagined it would need another carb overhaul so soon. Go figure as I was told this is rare. Crappy parts?

Anyway, drama resolved and thanks for the filter info. I will look into it today.

Best,
Chris


- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Europa-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group