 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
GalinHdz
Joined: 08 Nov 2017
Posts: 150
|
 Posted: Tue Jul 18, 2023 11:50 am Post subject: DYNON SkyView Roll Servo?? |
 |
|
What size DYNON roll servo have any of you used for the KIS4 and where did you mount it?
| | - The Matronics KIS-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?KIS-List |
|
|
|
| Back to top |
|
 |
Robert Reed
Joined: 22 Oct 2009
Posts: 331
Location: Dallas/Ft.Worth
|
| Posted: Tue Jul 18, 2023 12:45 pm Post subject: DYNON SkyView Roll Servo?? |
|
|
Galin
I used the smallest of the three available after determining that the movement was more than adequate. I installed it on a mount under the pilot seat on ground plate I had originally sized for the mount. The difference between your setup though is that you have the dual stick vs my single center stick.
Bob Reed
Sent from my iPhone
| Quote: | On Jul 18, 2023, at 2:52 PM, GalinHdz <GalinHdz(at)gmail.com> wrote:
What size DYNON roll servo have any of you used for the KIS4 and where did you mount it?
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=511116#511116
====================================
|
====================================
====================================
====================================
====================================
| | - The Matronics KIS-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?KIS-List |
|
| Description: |
|
| Filesize: |
123.14 KB |
| Viewed: |
5463 Time(s) |
|
| Description: |
|
| Filesize: |
137.27 KB |
| Viewed: |
5463 Time(s) |
|
|
|
| Back to top |
|
|
GalinHdz
Joined: 08 Nov 2017
Posts: 150
|
|
| Back to top |
|
|
Robert Reed
Joined: 22 Oct 2009
Posts: 331
Location: Dallas/Ft.Worth
|
| Posted: Wed Jul 19, 2023 7:34 am Post subject: DYNON SkyView Roll Servo?? |
|
|
I used the SV32 but ordered the longer arms, cut and tapped to length needed after mounting servo.
Bob Reed
Sent from my iPhone
| | - The Matronics KIS-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?KIS-List |
|
|
|
| Back to top |
|
|
GalinHdz
Joined: 08 Nov 2017
Posts: 150
|
| Posted: Wed Jul 19, 2023 10:17 am Post subject: Re: DYNON SkyView Roll Servo?? |
|
|
Did you have to cut much?
| | - The Matronics KIS-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?KIS-List |
|
|
|
| Back to top |
|
|
Robert Reed
Joined: 22 Oct 2009
Posts: 331
Location: Dallas/Ft.Worth
|
| Posted: Wed Jul 19, 2023 10:48 am Post subject: DYNON SkyView Roll Servo?? |
|
|
Which time? My first attempt had everything interfering with something or so it seemed. Had to reposition the servo closer to the connection on the center stick but that required a move of a couple of inches. Ended up cutting off about an inch or so if I remember correctly.
What was supposed to be a couple hour job turned into a multiple day job. Especially so for the rudder servo which I mounted under the center console between the front and back seat. I won't tell you how many expletives I uttered during all of that, would need a computer to calculate.
Anyway, everything is finally in place and proceeded to fight with the Dynon System to get it to recognize the servos. Haven't had the chance to fly it yet.
Bob
On Wednesday, July 19, 2023 at 01:19:18 PM CDT, GalinHdz <galinhdz(at)gmail.com> wrote:
--> KIS-List message posted by: "GalinHdz" <GalinHdz(at)gmail.com (GalinHdz(at)gmail.com)>
Did you have to cut much?
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=511127#511127
</==================
http://www.matronics.com/Navigator - MATRONICS WEB FORUMS -
/wiki.matronics.com" rel="nofollow" target="_blank">http://wiki.matroni=======================
</; &nb --> https://matronics.com/contribution
| | - The Matronics KIS-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?KIS-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
