Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Elevator arm opening

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Tailwind-List
View previous topic :: View next topic  
Author Message
lamphere(at)vabb.com
Guest





PostPosted: Thu May 17, 2007 2:43 pm    Post subject: Elevator arm opening Reply with quote

I haven't been able to figure out what everyone does to allow the elevator
horn to be put inside the covered tail section of the fuse.

Access door/panel where horn enters fuse?

Circular hole in fabric, insert horn into fuse, rotate onto stab and insert
bolts, reach in through fin access door and bolt together arms and pushrod?

No rush, but while I am covering the smaller parts, I'm wondering how you
put those tail feathers together - neatly.


- The Matronics Tailwind-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Tailwind-List
Back to top
jclement000(at)centurytel
Guest





PostPosted: Thu May 17, 2007 4:38 pm    Post subject: Elevator arm opening Reply with quote

Make a hole a little larger than the elevator horn and tube, about 1"wide x
11/4" high and do as you describe below. You should reinforce the hole area
with a second layer of fabric.
Jim C

---


- The Matronics Tailwind-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Tailwind-List



TW_JC9_Fabric_009.jpg
 Description:
 Filesize:  116.04 KB
 Viewed:  482 Time(s)

TW_JC9_Fabric_009.jpg


Back to top
bbernard1945(at)sbcglobal
Guest





PostPosted: Fri May 18, 2007 5:39 pm    Post subject: Elevator arm opening Reply with quote

Dave, That's pretty much how I ended up doing it. The holes in the fabric were reinforced with 0.016 aluminum glued to the fabric and covered with a fabric patch. A hole on both sides of the fin makes it easier to install and safety the nut holding the elevator horns and pushrod end together.

Bill
N40WB

David & Elaine Lamphere <lamphere(at)vabb.com> wrote:[quote] --> Tailwind-List message posted by: "David & Elaine Lamphere"

I haven't been able to figure out what everyone does to allow the elevator
horn to be put inside the covered tail section of the fuse.

Access door/panel where horn enters fuse?

Circular hole in fabric, insert horn into fuse, rotate onto stab and insert
bolts, reach in through fin access door and bolt together arms and pushrod?

No rush, but while I am [quote][b]


- The Matronics Tailwind-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Tailwind-List
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Tailwind-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group