Matronics Email Lists :: View topic

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

Canopy Side Frame

Matronics Email Lists Forum Index -> Zenith-List

View previous topic :: View next topic

Author Message

heatonhe36(at)msn.com
Guest

Posted: Wed Aug 29, 2007 4:50 pm Post subject: Canopy Side Frame

Hi Group,



I am in the process of building my canopy frame for my 601XL.  I can't find 

a dimension for the steel plate (0.05 x 100 x 30) welded at 31 deg to the 

side of the side frame.  My plans are from April, 04 and I am looking at 

page 6-C-2, top, center iso view.  The plate appears to be about 150mm back 

from the front pivot point but that's just a wag.  Any help from those who 

have been there would be greatly appreciated.



Thanks in advance,

Herb

Colorado Springs

601XL plans built, Turbo Subaru

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

Jaybannist(at)cs.com
Guest

Posted: Wed Aug 29, 2007 6:02 pm Post subject: Canopy Side Frame

Herb,



That piece is shown on my drawings (07/05) and the location is not dimensioned.  However, the location is not critical.  The outside cover for the forward part of the frame is secured by the pivot bolt and by riveting to this plate.  Mine is already covered up or I would measure it for you. Since the location is not critical, I would just "eyeball" it.



Jay in Dallas



"Herb Heaton" <heatonhe36(at)msn.com> wrote:



 	  Quote: 	
		  



Hi Group,



I am in the process of building my canopy frame for my 601XL.  I can't find 

a dimension for the steel plate (0.05 x 100 x 30) welded at 31 deg to the 

side of the side frame.  My plans are from April, 04 and I am looking at 

page 6-C-2, top, center iso view.  The plate appears to be about 150mm back 

from the front pivot point but that's just a wag.  Any help from those who 

have been there would be greatly appreciated.



Thanks in advance,

Herb

Colorado Springs

601XL plans built, Turbo Subaru

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

wjones(at)brazoriainet.co
Guest

Posted: Wed Aug 29, 2007 6:03 pm Post subject: Canopy Side Frame

Hi Herb, I had the same problem .I just looked at the pictures and placed it 

where it looked like it sould be .The only purpose of this piece is to 

recieve 3 rivets attaching 6C3-6 . Mine worked out fine ,so close should be 

good enough .

Wade Jones    South Texas

601XL plans building

Cont. 0200

---

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

GLJSOJ1

Joined: 18 Aug 2007
Posts: 82
Location: Chesapeake, Virginia

Posted: Thu Aug 30, 2007 5:28 am Post subject: Re: Canopy Side Frame

JUST MEASURED MINE FROM THE KIT AND IT IS 210 MM FROM CENTER OF THE CANOPY RAIL HINGE BOLT TO THE BEGINNING OF THE STEEL PLATE. I HAVE BEEN WORKING WITH THE FLASHING THAT ATTACHES THERE FOR OVER A WEEK OFF AND ON, BUT I FINALLY GOT IT LIKE I WANTED IT.



THANKS TO ALL HOW HELPED ME WITH THAT



GLENN

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

_________________
601XL N676L FLYING PHASE I
CHESAPEAKE VA

Display posts from previous:

	Matronics Email Lists Forum Index -> Zenith-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum