Matronics Email Lists :: View topic - Riveting Fuse Side Skins

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

Riveting Fuse Side Skins

Matronics Email Lists Forum Index -> RV10-List

View previous topic :: View next topic

Author Message

ron.mcgann(at)baesystems.
Guest

Posted: Wed Feb 22, 2006 3:00 pm Post subject: Riveting Fuse Side Skins

G'day all,   

I'm about to start riveting the fuse side skins.  Has anyone had any success backriveting these skins?  If so, what is the trick for preventing damage to the ribs/floor panels while climbing around inside?  

If your are near this point, have a look at Rick Sked's fuse stand in Tim Olsons page under fuselage tips. Looks neat, easy to build and versatile.  I had not noticed it before.  I guess the only down side is the height is fixed.  

thanks in advance,  

Ron  

#187 fuse

- The Matronics RV10-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

rvreynolds(at)macs.net
Guest

Posted: Thu Feb 23, 2006 2:42 pm Post subject: Riveting Fuse Side Skins

We hung ours vertical resting against 2 2X4 at a height that allowed easy access. Did the same for the tail cone.

Richard Reynolds

Norfolk, VA



On Feb 22, 2006, at 5:58 PM, McGANN, Ron wrote:

 	  Quote: 	
		    

G'day all, 

I'm about to start riveting the fuse side skins.  Has anyone had any success backriveting these skins?  If so, what is the trick for preventing damage to the ribs/floor panels while climbing around inside?

If your are near this point, have a look at Rick Sked's fuse stand in Tim Olsons page under fuselage tips. Looks neat, easy to build and versatile.  I had not noticed it before.  I guess the only down side is the height is fixed.

thanks in advance, 

Ron 

#187 fuse

- The Matronics RV10-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

ron.mcgann(at)baesystems.
Guest

Posted: Thu Feb 23, 2006 3:03 pm Post subject: Riveting Fuse Side Skins

Hi  Richard,

  

 I'm  intrigued.  Can you shed some more light (a picture would be  awesome)?  Did you suspend the fuse from the ceiling/rafter?  If  so, did you suspend from the centre section spars?

  

 thanks 

 Ron  

 [quote]   --

- The Matronics RV10-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

rvreynolds(at)macs.net
Guest

Posted: Fri Feb 24, 2006 5:31 am Post subject: Riveting Fuse Side Skins

Ron,

See attached pictures.



For the floor (RV-9A), I erected two vertical posts and clamped two athwartship braces under the forward and aft spars. The floor is clamped to the braces.



For the tailcone (RV-10), it was quicker to just set up a ladder and use the tail hook to secure it, Put some padding on the ladder. The bottom skin (J bars) had been completely back riveted before it was assembled into the sides and tops. Leave room at the floor to get inside. See the feet of person inside! The very aft end was finished by putting the tailcone on some low saw horses. In the pictures, the skins aft of F109? are still clecoed. 



If you do not have room in the workshop, move outside for the hour or so it takes to rivet the structure together,



Make your supports secure. Do not drop the assembly on the floor.



Richard Reynolds

Norfolk, VA



[img]cid:D565C902-4241-4478-B39D-65B36BD2142D(at)local[/img][img]cid:FFAF55BE-7EF0-4449-A6E2-4F33E4C72F6A(at)local[/img][img]cid:BB353642-DC06-4382-A6DA-5740FF3C65F7(at)local[/img]

On Feb 23, 2006, at 6:02 PM, McGANN, Ron wrote:

[quote]  Hi Richard,

  

 I'm intrigued.  Can you shed some more light (a picture would be awesome)?  Did you suspend the fuse from the ceiling/rafter?  If so, did you suspend from the centre section spars?

  

 thanks 

 Ron  

 [quote]  --

- The Matronics RV10-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

RV-9A_FloorA.jpg

Description:

Filesize:

135.91 KB

Viewed:

357 Time(s)

RV-9A_FloorB.jpg

Description:

Filesize:

125.27 KB

Viewed:

363 Time(s)

RV-10_Tailcone.jpg

Description:

Filesize:

149.42 KB

Viewed:

344 Time(s)

Display posts from previous:

	Matronics Email Lists Forum Index -> RV10-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum