 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
jskiba(at)icosa.net
Guest
|
 Posted: Sun Dec 30, 2007 2:39 pm Post subject: Tap into antenna coax? |
 |
|
I realize this is an old post but the link below:
http://aeroelectric.com/articles/commtap/commtap.html
returns a page not found, I tried looking manually for the info but seem to
not be able to find it.
Can anyone advise ?
--
| | - The Matronics AeroElectric-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?AeroElectric-List |
|
|
|
| Back to top |
|
 |
jskiba(at)icosa.net
Guest
|
|
| Back to top |
|
|
nuckolls.bob(at)cox.net
Guest
|
| Posted: Fri Jan 04, 2008 12:41 pm Post subject: Tap into antenna coax? |
|
|
At 08:05 AM 1/4/2008 -0600, you wrote:
This comic-book on crafting a panel
mounted jack to tap into the comm antenna
coax borrowed from this product by
ICOM:
http://www.aeroelectric.com/Pictures/Antenna/ICOM_HH_Adapter_2.jpg
http://www.aeroelectric.com/Pictures/Antenna/ICOM_HH_Adapter_2.jpg
Except that the version I proposed was much
more compact:
http://www.aeroelectric.com/Pictures/Antenna/CommTap-Jack.jpg
However, both designs relied on a miniature, close-
circuit phone jack similar to:
http://www.aeroelectric.com/Pictures/Connectors/Audio/3p5_mm_Jack.jpg
which mates with this plug:
http://www.aeroelectric.com/Pictures/Connectors/Audio/3p5_mm_Phone_Plug.jpg
The quality of the "closed circuit" switch labeled with
the "!" puts the panel mounted comm radio at risk. Switches
of this variety tend to get funky with age. They're "closed"
at any time the hand held radio is not plugged in such
that the comm radio is connected to the antenna. Corrosion
on these open, low pressure contacts can cause poor
connection to the antenna for the panel mounted radio.
Hence, my loss of enthusiasm for this approach to attaching
the hand held radio to ship's comm antenna. Until a better
idea comes along, consider looping some slack in the comm
antenna feedline through the cockpit and breaking it
with an in-line pair of connectors:
http://www.aeroelectric.com/Pictures/Connectors/Coax/BNC_Cable_Female_2.jpg
http://www.aeroelectric.com/Pictures/Connectors/Coax/BNC_Cable_Male.jpg
If you make this joint accessible in the cockpit,
then it's easy to open the connectors and route
the "slack" up to the hand-held's antenna jack.
Consider adding a couple of right-angle adapters
to the end of the antenna coax:
http://www.aeroelectric.com/Pictures/Connectors/Coax/BNC_Rt-Angle_Adapt_1.jpg
These can be used to make a tight u-turn for the
antenna feeder such that it will lay tightly against
the back of the radio. A rubber-band will keep it
snug against the radio. This gets around having
the coax make a wide loop above the radio and makes
it much easier to handle in the cockpit.
Bob . . .
| | - The Matronics AeroElectric-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?AeroElectric-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
