Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

No Title

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Zenith-List
View previous topic :: View next topic  
Author Message
bryanmmartin



Joined: 10 Jan 2006
Posts: 1018

PostPosted: Tue Jan 01, 2008 8:22 am    Post subject: No Title Reply with quote

I had a 24' Haulmark trailer that I built the plane in and used it to transport the plane to the airport for final assembly. I had to leave the fiberglass stabilizer tip fairings off because the stabilizer was too wide to fit through the door otherwise. The fuselage fit in the trailer just fine with the main gear installed and the nose facing the rear. When I mounted the engine, the engine would extend past the rear door so I had to put the plane in nose forward. The distance between the wheel wells was just a bit too narrow for the main gear with the wheels installed. I managed to fit the pane in the trailer by removing the main gear axles and installing a pair of tool box wheels mounted to short pieces of angle iron that I bolted to the inside of the main gear spring. Then I just wheeled the fuselage into the trailer. I had to put a ramp for the nose wheel to raise it up in order to lower the rudder below ceiling level. With the tool box wheels installed, the fuselage just happened to sit at the same attitude it did with the main wheels installed.
Here's a picture of the fuselage with wings fitted before the engine was mounted, you can see the tool box wheels installed:

[img]cid:5BF5DC9C-2F1D-42E8-8708-E95B26553308[/img]
Jaybannist(at)cs.com (Jaybannist(at)cs.com) wrote:
Quote:
--> Zenith-List message posted by: Jaybannist(at)cs.com (Jaybannist(at)cs.com)

Listers,

I'm sure some of you have faced this: I am very near the point of moving my fuselage to the airport. I planned on renting a truck to take it there. However, I have not been able to find a rental truck that is wide enough for the main gear. Most rental companies have trucks that are around 7'-6" wide. As you know, the gear is a little over 8'-0" wide. I just don't think it is feasible to transport the fuselage without the gear in place.



--
Bryan Martin
N61BM, CH 601 XL,
RAM Subaru, Stratus redrive.
do not archive.


- The Matronics Zenith-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List



File0142.jpg
 Description:
 Filesize:  73.78 KB
 Viewed:  164 Time(s)

File0142.jpg



_________________
--
Bryan Martin
N61BM, CH 601 XL, Stratus Subaru.
do not archive.
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Zenith-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group