 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
lwinger
Joined: 21 Jun 2006
Posts: 229
Location: Tustin, CA
|
 Posted: Sun Feb 03, 2008 10:48 am Post subject: 115mm flanging die needed |
 |
|
Hi Randy,
I haven't seen or heard much from you recently on the Zenith list. I hope you are doing well.
Unless I mess up a part (which could always happen!), I think I'm done using your flanging dies. They have been a great help, and worked so well. Thanks for the extended use.
I'll be glad to ship them back to you, or I can also hold on to them until another builder contacts you for their use. Then I could ship them direct, saving you the postage. It is your call.
Just let me know.
Thank you, again.
Larry Winger
On Jul 26, 2007 11:24 AM, Randy L. Thwing <n4546v(at)mindspring.com (n4546v(at)mindspring.com)> wrote:
[quote]Hey Larry:
If you don't get a better offer, my "iron" dies are available. They are
currently in the "custody" of Builder John Bolding in Texas who is finished
with them and awaiting shipping instructions. It is the three die set that
needs to stay together, but it is my understanding that the three dies will
fit in a postal flat rate box and ship for under ten bucks.
Let me know if you want them.
Best Regards,
Randy L. Thwing, Las Vegas do not archive
Subject: 115mm flanging die needed
| Quote: | --> Zenith-List message posted by: "lwinger" <larrywinger(at)gmail.com (larrywinger(at)gmail.com)>
Thanks to a good building buddy, I already have two sets of flanging dies
(65mm and 95mm). I'm missing the larger 115mm dies for my wing ribs.
|
| Quote: |
Is there anyone on the list with a 115mm set that I could use for a few
weeks? I'll be glad to pay shipping both ways. Thanks.
|
>
| Quote: | Feel free to contact me off list.
Do not archive.
--------
Larry Winger
Tustin, CA
601XL/Corvair from scratch
Control surfaces and wing spars complete
> Making wing ribs
|
[b]
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
_________________
Larry Winger
Tustin, CA
Plans building 601XL/650 with Corvair
Installing fuel system
www.mykitlog.com/lwinger |
|
| Back to top |
|
 |
Terry Phillips
Joined: 11 Jan 2006
Posts: 346
Location: Corvallis, MT
|
| Posted: Sun Feb 03, 2008 2:44 pm Post subject: 115mm flanging die needed |
|
|
Randy
I could definitely use them for a week or so. I just need to make up two parts to mount my landing & taxi lights. I haven't designed the part yet, but each will have a lightening hole. I was about to make some wooden ones, but I would be happy to pay shipping to borrow yours.
Terry
At 10:43 AM 2/3/2008 -0800, you wrote:
| Quote: | Hi Randy,
I haven't seen or heard much from you recently on the Zenith list. I hope you are doing well.
Unless I mess up a part (which could always happen!), I think I'm done using your flanging dies. They have been a great help, and worked so well. Thanks for the extended use.
I'll be glad to ship them back to you, or I can also hold on to them until another builder contacts you for their use. Then I could ship them direct, saving you the postage. It is your call.
Just let me know.
Thank you, again.
Larry Winger
On Jul 26, 2007 11:24 AM, Randy L. Thwing <n4546v(at)mindspring.com (n4546v(at)mindspring.com)> wrote:
Hey Larry:
If you don't get a better offer, my "iron" dies are available. They are
currently in the "custody" of Builder John Bolding in Texas who is finished
with them and awaiting shipping instructions. It is the three die set that
needs to stay together, but it is my understanding that the three dies will
fit in a postal flat rate box and ship for under ten bucks.
Let me know if you want them.
Best Regards,
Randy L. Thwing, Las Vegas do not archive
Subject: 115mm flanging die needed
> --> Zenith-List message posted by: "lwinger" <larrywinger(at)gmail.com (larrywinger(at)gmail.com)>
>
> Thanks to a good building buddy, I already have two sets of flanging dies
(65mm and 95mm). I'm missing the larger 115mm dies for my wing ribs.
>
> Is there anyone on the list with a 115mm set that I could use for a few
weeks? I'll be glad to pay shipping both ways. Thanks.
>
> Feel free to contact me off list.
>
> Do not archive.
>
> --------
> Larry Winger
> Tustin, CA
> 601XL/Corvair from scratch
> Control surfaces and wing spars complete
> Making wing ribs
|
Terry Phillips
ttp44~at~rkymtn.net
Corvallis MT
601XL/Jab 3300 s .. l .. o .. o.. w build kit - Tail, flaps, & ailerons are done; working on the wings
http://www.mykitlog.com/N47TP/ [quote][b]
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
_________________
Terry Phillips
Corvallis, MT
ttp44<at>rkymtn.net
Zenith 601XL/Jab 3300 slow build kit - Tail feathers done; working on the wings. |
|
| Back to top |
|
|
n4546v(at)mindspring.com
Guest
|
| Posted: Sun Feb 03, 2008 6:05 pm Post subject: 115mm flanging die needed |
|
|
do not archive
Hey Larry:
Glad the dies have worked ok with you. I think I remember you were building a 601, is that right? Was there a hole that required flanging in the 601 that my dies wouldn't work in? One that would require "trimming" of the dies to fit between flanges or something. Builder Larry Husky in Oregon advised me there is such a hole.
Anyway, for the moment, hang onto the dies. there were some other builders looking for them, but I can't remember who they were. I don't require them at the moment.
If one of my dies does require trimming to accomplish a hole, I need input and measurements so I or someone can do the alteration. I already trimmed the smallest die to do a hole in the 701, but I don't have the info for the 601.
Anyway, please hold onto the dies for the time being until we receive further orders.
Best regards,
Randy, Las Vegas
[quote] ---
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
|
|
| Back to top |
|
|
n4546v(at)mindspring.com
Guest
|
| Posted: Sun Feb 03, 2008 6:37 pm Post subject: 115mm flanging die needed |
|
|
do not archive
Hello Terry:
I have sent you a photo of the dies in use by private message. Let me know if they look like something you can use.
Regards,
Randy, Las Vegas
[quote] ---
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
