 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
countzero
Joined: 25 Oct 2007
Posts: 25
|
 Posted: Sat Apr 12, 2008 10:57 am Post subject: Fibreglass Tail Tip Trim |
 |
|
Hi,
I'm trimming the edges of the FTTs and I'm not sure how much I can take off. Drawing 6-X-1 shows the tip to tip width of the tail is 2.3m and the tail skeleton is 2.205m wide without the tips.
I only need to trim 5mm off each FFT to tidy the edges up but the tail measures 2.345m wide with the tips in place as it is. The tail would then be 2.335m wide, too wide.
To get the 2.3m width I would need to remove 22.5mm off each tip, that will not work. Any suggestions?
Many thanks
Rob
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
| Description: |
|
| Filesize: |
414.79 KB |
| Viewed: |
495 Time(s) |
|
|
|
| Back to top |
|
 |
bryanmmartin
Joined: 10 Jan 2006
Posts: 1018
|
| Posted: Sat Apr 12, 2008 1:25 pm Post subject: Fibreglass Tail Tip Trim |
|
|
Go ahead and trim them for a good fit and don't worry if it's a
little bit wider than the plans show, it won't hurt anything. The
extra width will just give you slightly more pitch stability. The
early 601HD's didn't have the fiberglas tips, they were added to
improve pitch stability.
| Quote: |
Hi,
I'm trimming the edges of the FTTs and I'm not sure how much I can
take off. Drawing 6-X-1 shows the tip to tip width of the tail is
2.3m and the tail skeleton is 2.205m wide without the tips.
I only need to trim 5mm off each FFT to tidy the edges up but the
tail measures 2.345m wide with the tips in place as it is. The tail
would then be 2.335m wide, too wide.
To get the 2.3m width I would need to remove 22.5mm off each tip,
that will not work. Any suggestions?
|
--
Bryan Martin
N61BM, CH 601 XL,
RAM Subaru, Stratus redrive.
do not archive.
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
_________________
--
Bryan Martin
N61BM, CH 601 XL, Stratus Subaru.
do not archive. |
|
| Back to top |
|
|
countzero
Joined: 25 Oct 2007
Posts: 25
|
| Posted: Sun Apr 13, 2008 12:50 am Post subject: Re: Fibreglass Tail Tip Trim |
|
|
Thanks Byran, it's just that my garage door is only 2.320!
| Quote: | | and don't worry if it's a little bit wider than the plans show |
| Quote: | | The tail would then be 2.335m wide, too wide |
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
|
|
| Back to top |
|
|
bryanmmartin
Joined: 10 Jan 2006
Posts: 1018
|
| Posted: Sun Apr 13, 2008 7:37 am Post subject: Fibreglass Tail Tip Trim |
|
|
I had to wait until the final assembly phase at the airport to rivet
my fiberglas tips on. I built my plane in a 24 foot cargo trailer and
the rear door opening was too narrow to get the fuselage through with
the tips on. But then, I never had any intention of storing the plane
in the trailer after it was finished and flying.
If you are planning on storing the plane in your garage after it's
finished, you might consider attaching the tips with small screws so
that it can be removed. Or you can widen the door. 
On Apr 13, 2008, at 4:50 AM, countzero wrote:
| Quote: |
Thanks Byran, it's just that my garage door is only 2.320!
> and don't worry if it's a little bit wider than the plans show
> The tail would then be 2.335m wide, too wide
|
--
Bryan Martin
N61BM, CH 601 XL,
RAM Subaru, Stratus redrive.
do not archive.
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
_________________
--
Bryan Martin
N61BM, CH 601 XL, Stratus Subaru.
do not archive. |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
