 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
AZFlyer
Joined: 11 Jan 2006
Posts: 89
Location: Prescott, AZ
|
 Posted: Mon May 19, 2008 9:30 am Post subject: Flap Controls Installation Question |
 |
|
Builders,
Have installed and tested my flap controls; however, am now ready to tighten down the bolts holding actuator and other end (6B19-7 connect to 6B19-3). The call-out on 6-B-19, in the lower left corner dwg. is for a AN5-11a bolt with 3 washers.
After placing the 3 washers on the rod-end CW5-12, I stepped back and looked at it...doesn't look right. 6B19-3 is distorted open. Can not believe that is what was intended. Are 3 washers needed? Any feedback would be appreciated.
Thanks,
Mike
do not archive
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
_________________
Mike Miller @ millrml@aol.com
601 XL-B, 3300, Dynon
Remember, "the second mouse gets the cheese"! |
|
| Back to top |
|
 |
bryanmmartin
Joined: 10 Jan 2006
Posts: 1018
|
| Posted: Mon May 19, 2008 12:56 pm Post subject: Flap Controls Installation Question |
|
|
I don't have the drawings or the plane handy right now but, as I recall, the washers should go directly under the bolt head and/or the nut. The flap actuator lever (6B19-3?) should clamp down directly on the rod end with no washers in between. The washers just prevent the nut from bottoming out on the bolt shank.
-------------- Original message ----------------------
From: "AZFlyer" <millrML(at)AOL.com>
| Quote: |
Builders,
Have installed and tested my flap controls; however, am now ready to tighten
down the bolts holding actuator and other end (6B19-7 connect to 6B19-3). The
call-out on 6-B-19, in the lower left corner dwg. is for a AN5-11a bolt with 3
washers.
After placing the 3 washers on the rod-end CW5-12, I stepped back and looked at
it...doesn't look right. 6B19-3 is distorted open. Can not believe that is
what was intended. Are 3 washers needed? Any feedback would be appreciated.
|
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
_________________
--
Bryan Martin
N61BM, CH 601 XL, Stratus Subaru.
do not archive. |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
