 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
rowlandcarson(at)googlema
Guest
|
 Posted: Fri Jul 04, 2008 10:04 am Post subject: making holes in fuselage moulding |
 |
|
I'm constructing a vey simple fuselage dolly from odds and ends.
To stop the fuselage lower moulding sliding around on the dolly when
I move it, I'm thinking of putting a couple of screws through the
bottom of the moulding into the dolly, in the area that is going to
be cut out for the (mono) wheel. Not to clamp it down tight, just to
provide some lateral location.
Anyone see any reason not to to make a couple of holes in what will
eventually become waste?
regards
Rowland
--
| Rowland Carson LAA #16532 http://home.clara.net/rowil/aviation/
| 1030 hours building Europa #435 G-ROWI e-mail <rowil(at)clara.net>
| | - The Matronics Europa-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Europa-List |
|
|
|
| Back to top |
|
 |
jrgowing(at)bigpond.net.a
Guest
|
| Posted: Fri Jul 04, 2008 2:46 pm Post subject: making holes in fuselage moulding |
|
|
Rowland
If youy are going to cut it out later how could it hurt anything?
Looks as if you can do it!
JR (Bob) Gowing UK kit 327 in Oz
do not archive
---
| | - The Matronics Europa-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Europa-List |
|
|
|
| Back to top |
|
|
rlborger(at)mac.com
Guest
|
| Posted: Fri Jul 04, 2008 3:34 pm Post subject: making holes in fuselage moulding |
|
|
Rowland,
Sounds like a great idea to me.
Good building and great flying,
Bob Borger
Europa Kit #A221 N914XL, XS Mono, Intercooled 914, Airmaster C/S
http://www.europaowners.org/N914XL
(95% done, only 95% to go) tail kit done, wings closed, cockpit module
installed, pitch system in, landing gear complete, rudder system in
with Singleton Mod, outrigger mod in, Fuselage Top on, lift/drag/flap
pins in, wing incidence set, tie bar in, flap drive in, baggage bay
in. Fuel system complete. Rotax and Airmaster installed. Mods 62,
66, 70 & 72 done. Completed the instrument panel install. Europa
interior kit being installed. Installed windows. Working in - 25
Electrical, 28 Flaps, 30 Fuel System, 32 Tail, 34 Door Latches & 35
Doors, 37 Finishing. Mostly finishing these days.
3705 Lynchburg Dr.
Corinth, TX 76208
Home: 940-497-2123
Cel: 817-992-1117
On Jul 4, 2008, at 13:00, Rowland Carson wrote:
| Quote: |
>
I'm constructing a vey simple fuselage dolly from odds and ends.
To stop the fuselage lower moulding sliding around on the dolly when
I move it, I'm thinking of putting a couple of screws through the
bottom of the moulding into the dolly, in the area that is going to
be cut out for the (mono) wheel. Not to clamp it down tight, just to
provide some lateral location.
Anyone see any reason not to to make a couple of holes in what will
eventually become waste?
regards
Rowland
--
| Rowland Carson LAA #16532 http://home.clara.net/rowil/aviation/
| 1030 hours building Europa #435 G-ROWI e-mail <rowil(at)clara.net>
|
| | - The Matronics Europa-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Europa-List |
|
|
|
| Back to top |
|
|
budyerly(at)msn.com
Guest
|
| Posted: Fri Jul 04, 2008 3:38 pm Post subject: making holes in fuselage moulding |
|
|
<?xml:namespace prefix="v" /><?xml:namespace prefix="o" /><![endif]--> Do it all the time...Just don't screw up into the tank or your wiring...Eh.
Even if you need to put a screw with some wood or epoxy to shim or add stiffness. Grind it out when your done. I love fiberglass, just cut and glue.
Bud Yerly
[quote] ---
| | - The Matronics Europa-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Europa-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
