Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Z13/8 wiring correction ?

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> AeroElectric-List
View previous topic :: View next topic  
Author Message
jpx(at)Qenesis.com
Guest
PostPosted: Wed Jul 16, 2008 6:19 am    Post subject: Z13/8 wiring correction ? Reply with quote
Please look closely at the switch wiring for the E-Mag in Z13/8.

The operation of the switch as pictured is correct. That is the power
is applied to the E-Mag while the P Lead is still grounded, and the P
Lead is grounded before power is removed.

However, the pictorial diagram of the switch does not match the
diagram of the 2-10 switch shown on Page 11-18.

Assuming that page 11-18 is correct, then the V+, pin 5 of the E-Mag
should be controlled by switch connections 2-1 and the P Lead, pin 4
of the E-Mag should be controlled by switch connections 5-6.

Or am I mixed up about something ?

Jeff Page
Dream Aircraft Tundra #10

- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List
Back to top
nuckolls.bob(at)cox.net
Guest
PostPosted: Fri Jul 18, 2008 12:57 pm    Post subject: Z13/8 wiring correction ? Reply with quote
At 10:16 AM 7/16/2008 -0400, you wrote:
Quote:


Please look closely at the switch wiring for the E-Mag in Z13/8.

The operation of the switch as pictured is correct. That is the power
is applied to the E-Mag while the P Lead is still grounded, and the P
Lead is grounded before power is removed.

However, the pictorial diagram of the switch does not match the
diagram of the 2-10 switch shown on Page 11-18.

Assuming that page 11-18 is correct, then the V+, pin 5 of the E-Mag
should be controlled by switch connections 2-1 and the P Lead, pin 4
of the E-Mag should be controlled by switch connections 5-6.

Or am I mixed up about something ?


Good eye! I have to be careful when doing major edits
between various z-figures. Some of these drawings were
done 10 years ago before I discovered the differences
between Carling-Like and Microswitch-Like progressive
transfer conventions. A few drawings still have un-revised
blocks embedded in them. I've fixed the error you've
cited and published the new drawing at:

http://www.aeroelectric.com/PPS/Adobe_Architecture_Pdfs/Z13-8Q.pdf

Thanks for the heads-up.

Bob . . .

----------------------------------------)
( . . . a long habit of not thinking )
( a thing wrong, gives it a superficial )
( appearance of being right . . . )
( )
( -Thomas Paine 1776- )
----------------------------------------

- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List
Back to top
jpx(at)Qenesis.com
Guest
PostPosted: Sun Jul 20, 2008 6:34 am    Post subject: Z13/8 wiring correction ? Reply with quote
Bob,
Although I can display the document, I cannot save it. I suspect
there is a PDF flag that was incorrectly set when you produced the PDF.
Jeff Page

Quote:
I've fixed the error you've cited and published the new drawing at:
http://www.aeroelectric.com/PPS/Adobe_Architecture_Pdfs/Z13-8Q.pdf


- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List
Back to top
nuckolls.bob(at)cox.net
Guest
PostPosted: Sun Jul 20, 2008 6:53 am    Post subject: Z13/8 wiring correction ? Reply with quote
At 10:31 AM 7/20/2008 -0400, you wrote:
Quote:


Bob,
Although I can display the document, I cannot save it. I suspect
there is a PDF flag that was incorrectly set when you produced the PDF.
Jeff Page

> I've fixed the error you've cited and published the new drawing at:
> http://www.aeroelectric.com/PPS/Adobe_Architecture_Pdfs/Z13-8Q.pdf


It's the same settings I've used since day-one. The only
flags I have to remember to set each time I upload a file
to the server is to make them executable by all.
My ftp program doesn't do that automatically. I just
downloaded the file and saved it both through the browser
'save page as' and Adobe's file save tag.

Try right-clicking the link in your browser and telling
it where to store the file as opposed to opening directly
from the browser.

Bob . . .

----------------------------------------)
( . . . a long habit of not thinking )
( a thing wrong, gives it a superficial )
( appearance of being right . . . )
( )
( -Thomas Paine 1776- )
----------------------------------------

- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> AeroElectric-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group