Matronics Email Lists :: View topic - Recommendations prior to riveting seat floor/cargo floor.

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

Recommendations prior to riveting seat floor/cargo floor.

Matronics Email Lists Forum Index -> RV10-List

View previous topic :: View next topic

Author Message

Deems Davis

Joined: 09 Jan 2006
Posts: 925

Posted: Sun Nov 02, 2008 4:03 pm Post subject: Recommendations prior to riveting seat floor/cargo floor.

Some have put in sound proofing to the bottom of the skins prior to 

riveting.

Deems



woxofswa wrote:

 	  Quote: 	
		   



 I'm am at that point of riveting the seat floors.  I have the Van's wiring kit and was going to run a length of plastic conduit with pull strings along each side.  I have also ordered the SafeAir pitot static line kit and was going to run that.  



 Any other suggestions before riveting the floors?



 Thanks in advance.



 --------

 Myron Nelson

 Mesa, AZ

 Emp completed, legacy build fuse in progress





 Read this topic online here:



 http://forums.matronics.com/viewtopic.php?p 11854#211854

- The Matronics RV10-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

woxofswa

Joined: 12 Aug 2008
Posts: 349
Location: AZ

Posted: Sun Nov 02, 2008 5:17 pm Post subject: Re: Recommendations prior to riveting seat floor/cargo floo

Thanks Deems,



Yes, I did that already.  I went with the QuietRide kit.



I just perused yours and Tim's sites on that section.  I couldn't help but notice that you both did the same antenna and in the same place.



Could you expound upon the reasoning for your choice of antenna and location?

- The Matronics RV10-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

_________________
Myron Nelson
Mesa, AZ
Flew May 10 2014

Deems Davis

Joined: 09 Jan 2006
Posts: 925

Posted: Sun Nov 02, 2008 6:06 pm Post subject: Recommendations prior to riveting seat floor/cargo floor.

My logic/reasoning  was straight forward -------- I copied what Tim did 

!  

Deems



woxofswa wrote:

 	  Quote: 	
		   



 Thanks Deems,



 Yes, I did that already.  I went with the QuietRide kit.



 I just perused yours and Tim's sites on that section.  I couldn't help but notice that you both did the same antenna and in the same place.



 Could you expound upon the reasoning for your choice of antenna and location?



 --------

 Myron Nelson

 Mesa, AZ

 Emp completed, legacy build fuse in progress





 Read this topic online here:



 http://forums.matronics.com/viewtopic.php?p 11873#211873

- The Matronics RV10-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

woxofswa

Joined: 12 Aug 2008
Posts: 349
Location: AZ

Posted: Sun Nov 02, 2008 6:40 pm Post subject: Re: Recommendations prior to riveting seat floor/cargo floo

>>I copied what Tim did<<



My old debate coach would have called that "Cogent Analysis."

- The Matronics RV10-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

_________________
Myron Nelson
Mesa, AZ
Flew May 10 2014

planesmith(at)hotmail.com
Guest

Posted: Mon Nov 03, 2008 7:55 am Post subject: Recommendations prior to riveting seat floor/cargo floor.

It may be worth running an extra conduit or two C depending on the size of conduit you are using.

  

 Vern Smith (#324 finishing)

  

 do not archive





   

 > Subject: Recommendations prior to riveting seat floor/cargo floor.

 	  Quote: 	
		   From: woxof(at)aol.com

 Date: Sun C 2 Nov 2008 15:48:18 -0800

 To: rv10-list(at)matronics.com

 

 --> RV10-List message posted by: "woxofswa" <woxof(at)aol.com>

 

 I'm am at that point of riveting the seat floors. I have the Van's wiring kit and was going to run a length of plastic conduit with pull strings along each side. I have also ordered the SafeAir pitot static line kit and was going to run that. 

 

 Any other suggestions before riveting the floors?

 

 Thanks in advance.

 

 --------

 Myron Nelson

 Mesa C AZ

 Emp completed C legacy build fuse in progress

 

 

 

 

 Read this topic online here:

 

 http://forums.matronics.com/viewtopic.php?p=211854#211854

 

 

 

 

 

 

 

&===================
	


 	  Quote: 	
		   

 

 


	


Store C manage and share up to 5GB with Windows Live SkyDrive. Start uploading now  [quote][b]

- The Matronics RV10-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

Display posts from previous:

	Matronics Email Lists Forum Index -> RV10-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum