 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
rparigor(at)SUFFOLK.LIB.N
Guest
|
 Posted: Sat Dec 20, 2008 6:42 pm Post subject: How do you hold a pull able breaker opened |
 |
|
Hi Bob
| Quote: | >Anyway any ideas?
What is the diameter of the cb button under the
head? What is the gap (thickness of the clip)?
|
I just looked up spec sheet on W31 and they only provide head diameter
which is .315".
I will measure the length of head, and diameter and length of shaft
(smaller diameter than head) and report back.
Ron Parigoris
| | - The Matronics AeroElectric-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?AeroElectric-List |
|
|
|
| Back to top |
|
 |
rparigor(at)SUFFOLK.LIB.N
Guest
|
| Posted: Sun Dec 21, 2008 11:48 am Post subject: How do you hold a pull able breaker opened |
|
|
Hi Bob"> What is the diameter of the cb button under the > head? What is the gap (thickness of the clip)?>"The shaft sticking out of P+B pullable breaker has three tiers.Head is .312" diameter and .115" in length, and second tier below head is .250" in diameter and .200" in length, and third tier is .200" in diameter and .200" in length.Thus total shaft length sticking out measured from metal threaded portion to tip of head when pulled is .515" (.115" + .200" + .200"), with their three respective diameters (head being the largest) .312", .250", .200" .Ron Parigoris [quote][b]
| | - The Matronics AeroElectric-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?AeroElectric-List |
|
|
|
| Back to top |
|
|
jetboy
Joined: 22 Jul 2006
Posts: 233
|
| Posted: Sun Dec 21, 2008 6:52 pm Post subject: Re: How do you hold a pull able breaker opened |
|
|
Probably a bit OTT have you looked at fitting a 'missile switch' cover MS25224-1 looks close enough to accomadate .5" of breaker shaft if you drill out the cover for clearance in the protected position.
Perhaps a nicer way would be to recess the breaker so when pulled the button is level with the others.
Ralph
| | - The Matronics AeroElectric-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?AeroElectric-List |
|
_________________
Ralph - CH701 / 2200a |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
