Matronics Email Lists :: View topic - Elevator Gap Seal Test Report (image missing)

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

Elevator Gap Seal Test Report (image missing)

Matronics Email Lists Forum Index -> Kitfox-List

View previous topic :: View next topic

Author Message

Paul A. Franz, P.E.

Joined: 02 Dec 2008
Posts: 280
Location: Bellevue WA

Posted: Sat Jan 31, 2009 12:55 pm Post subject: Elevator Gap Seal Test Report (image missing)

On Sat, January 31, 2009 9:55 am, Rexinator wrote:

 	  Quote: 	
		   



 So has anyone thought of applying tape top and bottom with the adhesive

 fully contacting each other in the gap? Something like this:  >-<


	


That's a great idea. Or sew two pieces of fabric together and dope the V's as Jan of

"JC Propeller Design" suggested. You could use two parallel rows of stitching spaced

the width of the gap.



 	  Quote: 	
		      It would be very difficult to do well unless you could design and

 fabricate a special tool, but I think it could be done. I'm imagining

 careful measurement of your gap and tape width then positioning the tape

 on one side correctly such that it would allow the other side to be

 applied and close all of the gap with no significant spaces or air bubbles.


	


Applying strips of peelable release to the adhesive, cut just right could make this

fairly straight forward.



 	  Quote: 	
		    I think a perfect tool might be a stiff rubber block shaped to follow

 the half cross section of the intended gap seal. After the 1st side of

 tape has been applied (bottom?) then the block could be clamped on that

 side to hold the applied tape in the proper shape it would retain for

 the gap if the other side was already installed. Then it should be

 possible to lay the upper tape like positioning a large pre-cut decal.



   Here's an attempt of a drawing of the cross section with the tape red,

 block shape in black and a clamping bar in green.


	


 	  Quote: 	
		   Gap seal image


	


Your image/scan didn't come through. You might post it as an attachment or use the

forum interface.



 	  Quote: 	
		   Anybody following my attempt to describe this concept?


	


Would help to see your intended drawing/image.



-- 

Paul A. Franz

Registration/Aircraft - N14UW/Merlin GT

Engine/Prop - Rotax 914/NSI CAP

Bellevue WA

425.241.1618 Cell

- The Matronics Kitfox-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List

_________________
Paul A. Franz, P.E.
Registration/Aircraft - N14UW/Merlin GT
Engine/Prop - Rotax 914/NSI CAP
Bellevue WA
425.241.1618 Cell
425.440.9505 Office

rexinator

Joined: 31 Jan 2009
Posts: 33

Posted: Sat Jan 31, 2009 2:05 pm Post subject: Re: Elevator Gap Seal (image not missing)

I guess my forum registration expired as I couldn't log in as I had in the past. It's been a while.



 Here's the drawing I created for the gap seal idea.

- The Matronics Kitfox-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List

tape.jpg

Description:

gap seal drawing

Filesize:

7.63 KB

Viewed:

1979 Time(s)

Display posts from previous:

	Matronics Email Lists Forum Index -> Kitfox-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum