 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
tmakibbin
Joined: 24 Feb 2009
Posts: 2
Location: Enola, PA
|
 Posted: Tue Feb 24, 2009 2:47 pm Post subject: Spinner Fitting |
 |
|
I have the fiberglass spinner from USAJabiru. It is basically a cone with no cutout for the propeller (Understandable). But my question for anyone is, "how did you go about marking and making the cutouts for the propeller blades on the spinner?"
Thanks,
Tom
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
|
|
| Back to top |
|
 |
jaybannist(at)cs.com
Guest
|
| Posted: Tue Feb 24, 2009 3:08 pm Post subject: Spinner Fitting |
|
|
Tom,
I have a Van's spinner, but the process would be the same. I made a band out of Bristol board to simulate the lower portion of the spinner. I made rough cutouts for the prop blades then fine tuned the cutouts by applying pieces of masking tape to the edges of the rough cutout, until I got a close fit to the prop blades. That will then serve as a template for cutting the fiberglass cone. I used a fine toothed coping saw to make the actual cuts. I used part of the cutout fiberglass to make a filler for the opening behind the prop blades.
Jay Bannister
--
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
|
|
| Back to top |
|
|
DaveG601XL
Joined: 27 Oct 2006
Posts: 351
Location: Cincinnati, Oh
|
| Posted: Wed Feb 25, 2009 3:57 am Post subject: Re: Spinner Fitting |
|
|
Tom,
Like Jay said, templates are the way here. A few pictures attached show my template from cardboard. Start a little smaller than you think you need for the initial cut and then fit it to the prop. Make sure to mask the prop from scratches. Don't trim too close since the fiberglass will deflect in operation. Jabiru recommended at least a 1/8" gap in their literature. I did not think of a filler behind the prop as Jay did.
Good luck,
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
| Description: |
|
| Filesize: |
50.72 KB |
| Viewed: |
2786 Time(s) |
|
| Description: |
|
| Filesize: |
89.82 KB |
| Viewed: |
2786 Time(s) |
|
| Description: |
|
| Filesize: |
59.94 KB |
| Viewed: |
2786 Time(s) |
|
_________________
David Gallagher
Cincinnati, OH area |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
