Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Main Gear Support Rubbers' Replacemen - 601XL

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Zenith601-List
View previous topic :: View next topic  
Author Message
tonyplane(at)bellsouth.ne
Guest





PostPosted: Thu Apr 02, 2009 8:44 pm    Post subject: Main Gear Support Rubbers' Replacemen - 601XL Reply with quote

After over 1000 landings (over 150 very-rough field landings) it is time to
replace my main gear support rubbers. (I wondered what that rattling noise
was when taxiing over the grass/dirt-mud/ gravel - turned out to caused by a
missing "rubber" between the gear and fuselage gear support fitting on the
left hand side).

I have some ideas on how to jack up for replacement, but if anyone else has
done it on a full-up 601XL, I would appreciate info on how you did it.

Thanks,

Tony Graziano

Buchanan, Tn

XL/Jab3300; N493TG; 478 hrs


- The Matronics Zenith601-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith601-List
Back to top
jaybannist(at)cs.com
Guest





PostPosted: Fri Apr 03, 2009 5:11 am    Post subject: Main Gear Support Rubbers' Replacemen - 601XL Reply with quote

Tony,

When it came time to install my main gear, I found that I had supported the fuselage too low. I had to raise the fuselage to get clearance to install the gear. I had the rear of the fuselage supported on a jack stand, I set up the rig shown in the photos and lifted it VERY slowly ( I was working alone, so the pucker factor was really high ). I would lift it enough to get another 2 x 4 under it and lift again. I kept this up until I had the needed clearance and the nose gear firmly supported on blocks. When the main gear was installed, I just reversed the procedure. Hope this helps.

Jay Bannister





--


- The Matronics Zenith601-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith601-List



zodiac01-07-08_002a.jpg
 Description:
 Filesize:  193.86 KB
 Viewed:  1319 Time(s)

zodiac01-07-08_002a.jpg



zodiac01-07-08_003a.jpg
 Description:
 Filesize:  205.29 KB
 Viewed:  1319 Time(s)

zodiac01-07-08_003a.jpg


Back to top
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Zenith601-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group