 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
Jeyoung65(at)aol.com
Guest
|
 Posted: Sat May 02, 2009 1:13 pm Post subject: Control cables swagging |
 |
|
Does anyone know what dim. the swage limit is for NICOPRESS on 1/8 cable with manual tool? Jerry of GA
DO NOT ARCHIVE
Check all of your email inboxes from anywhere on the web. Try the new Email Toolbar now!
[quote][b]
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
|
|
| Back to top |
|
 |
psm(at)att.net
Guest
|
| Posted: Sat May 02, 2009 1:34 pm Post subject: Control cables swagging |
|
|
I believe the Nicopress limits are the same no matter what tool is used. I got a standard from Aircraft Spruce for a few bucks. I don't know the exact dimension required.
Paul
XL grounded
do not archive
At 02:11 PM 5/2/2009, you wrote:
[quote]Does anyone know what dim. the swage limit is for NICOPRESS on 1/8 cable with manual tool? Jerry of GA
DO NOT ARCHIVE
[b]
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
|
|
| Back to top |
|
|
notsew_evets(at)frontiern
Guest
|
| Posted: Sat May 02, 2009 1:34 pm Post subject: Control cables swagging |
|
|
I purchased a "go-no go" gauge from ACS. Very stress relieving tool to have.
SW
[quote] ---
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
|
|
| Back to top |
|
|
larry(at)macsmachine.com
Guest
|
| Posted: Sat May 02, 2009 1:42 pm Post subject: Control cables swagging |
|
|
Hi Jerry,
The no-go gage pictured on my site for a 1/8th cable nicopress is
stamped at .355 gap.
Larry McFarland 601HDS at www.macsmachine.com
Jeyoung65(at)aol.com wrote:
| Quote: | Does anyone know what dim. the swage limit is for NICOPRESS on 1/8
cable with manual tool? Jerry of GA
DO NOT ARCHIVE
*=======
*
|
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
|
|
| Back to top |
|
|
Jeyoung65(at)aol.com
Guest
|
| Posted: Sat May 02, 2009 2:50 pm Post subject: Control cables swagging |
|
|
Thanks Larry. Jerry of GA
In a message dated 5/2/2009 4:43:23 P.M. Eastern Standard Time, larry(at)macsmachine.com writes:
| Quote: | --> Zenith-List message posted by: LarryMcFarland <larry(at)macsmachine.com>
Hi Jerry,
The no-go gage pictured on my site for a 1/8th cable nicopress is
stamped at .355 gap.
Larry McFarland 601HDS at www.macsmachine.com
Jeyoung65(at)aol.com wrote:
| Quote: | Does anyone know what dim. the swage limit is for NICOPRESS on 1/8
cable with manual tool? Jerry of GA
DO NOT ARCHIVE
*=======
======================== the ties Day ================================================ - MATRONICS WEB FORUMS ================================================ - List Contribution Web Site sp; ===================================================
|
|
Check all of your email inboxes from anywhere on the web. Try the new Email Toolbar now!
[quote][b]
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
|
|
| Back to top |
|
|
paulrod36(at)msn.com
Guest
|
| Posted: Sun May 03, 2009 10:27 am Post subject: Control cables swagging |
|
|
<?xml:namespace prefix="v" /><?xml:namespace prefix="o" /><![endif]--> If you're using a tool supplied by one of the aircraft houses (I suspect they're all made in some back alley in Hong Kong), the dimension when the tool is completely closed should be right. To double check, you'll find the dimension in 43-13.
Paul Rodriguez
[quote] ---
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
