Matronics Email Lists :: View topic - RV-7 F-732B/F drawing inconsistency question

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

RV-7 F-732B/F drawing inconsistency question

Matronics Email Lists Forum Index -> RV-List

View previous topic :: View next topic

Author Message

ceengland(at)bellsouth.ne
Guest

Posted: Sat Jul 18, 2009 3:40 pm Post subject: RV-7 F-732B/F drawing inconsistency question

After several months of minimal building activity, & a year or more 

since building the fuselage, I'm gearing up to install the tipup rear 

window & aft top skin.



I haven't dimpled the skin yet, so I pulled out the small version of 

drawing 40 to see how to dimple/countersink the area where the skin sits 

on the F706 bulkhead & F732A brace. Detail G, and other drawings on the 

page, show an angle brace, F732B. The actual piece I made a year or more 

ago is a piece of flat 1/8" aluminum. After digging through the 

instructions for a half-hour or so trying to find the directions for 

building the part, I pulled out the full size drawing to see details a 

bit better. Hmmm... *That* drawing detail G shows a flat piece of metal, 

F732H. The two drawings have the same rev# & date.



I'm hoping that the 'H' means I'm good to go, but has anyone talked to 

Van's about this?



Thanks,



Charlie

- The Matronics RV-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV-List

FisherPaulA(at)JohnDeere.
Guest

Posted: Mon Jul 20, 2009 8:08 am Post subject: RV-7 F-732B/F drawing inconsistency question

Charlie,

Perhaps you are confused because of the service bulletin (SB 05-1-1) on this intersection?  See http://vansaircraft.com/pdf/sb05-1-1.pdf for the full details!  If your plans are as old as mine, then they will not be correct - you'll have to refer to the document cited above.  



I only remembered because the FAA is scheduled to come and do my final inspection this week and I added all of the service bulletins to the log book so I could show compliance. The FAA seems to like that level of detail!



Paul A. Fisher

RV-7A N18PF "any day now!"

--

- The Matronics RV-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV-List

ceengland(at)bellsouth.ne
Guest

Posted: Mon Jul 20, 2009 11:23 am Post subject: RV-7 F-732B/F drawing inconsistency question

Ahhh, yes, that's the ticket. The frustrating thing is that the 'old' 

configuration is shown on the small drawing & the 'new' configuration is 

shown on the large drawing, but both have exactly the same dates, file 

names, etc in the data block.



Thanks,



Charlie



Fisher Paul A. wrote:

[quote] 



 Charlie,

 Perhaps you are confused because of the service bulletin (SB 05-1-1) on this intersection?  See http://vansaircraft.com/pdf/sb05-1-1.pdf for the full details!  If your plans are as old as mine, then they will not be correct - you'll have to refer to the document cited above.  



 I only remembered because the FAA is scheduled to come and do my final inspection this week and I added all of the service bulletins to the log book so I could show compliance. The FAA seems to like that level of detail!



 Paul A. Fisher

 RV-7A N18PF "any day now!"

 --

- The Matronics RV-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV-List

Display posts from previous:

	Matronics Email Lists Forum Index -> RV-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum