 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
Lee Steensland
Joined: 10 Apr 2008
Posts: 18
Location: Spokane-ish- WA
|
 Posted: Sun Aug 02, 2009 1:37 pm Post subject: upper and lower elevator horn doubler location |
 |
|
Folks,
Perhaps I'm being particularly thick today but I could use a hand. I am starting on the elevator horns and something appears to be amiss. I haven't cut any metal yet so I'm safe, but I can't figure out from the plans where to make the triangular cutout in the elevator for 6-t-3-6.
As near as I can figure it's at least the length of the top flange on the skin (20mm) rearward from the front of the elevator, and at least big enough to take the 3/4 inch piece of extrusion (20mm).
How did you guys come up with that dimension?
Thanks!
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
|
|
| Back to top |
|
 |
floyd wilkes
Joined: 11 Jun 2007
Posts: 39
Location: spring branch, tx
|
| Posted: Sun Aug 02, 2009 6:12 pm Post subject: upper and lower elevator horn doubler location |
|
|
Lee,
Check your builders guide 6-T-3A page 11. Third and fourth photo show where
it goes.
Floyd Wilkes
601XL O-200
do not archive
---
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
_________________
Floyd Wilkes |
|
| Back to top |
|
|
Lee Steensland
Joined: 10 Apr 2008
Posts: 18
Location: Spokane-ish- WA
|
| Posted: Sun Aug 02, 2009 7:22 pm Post subject: Re: upper and lower elevator horn doubler location |
|
|
Awesome I found it there.
One more question, kind of nit picking now I suppose.
The bottom hole says "8 mm from the bottom bend". I basically laid a straightedge on the front spar and measured my 8mm from there. Is that right or should I start measuring 8mm from the flat, (after the bend)?
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
|
|
| Back to top |
|
|
floyd wilkes
Joined: 11 Jun 2007
Posts: 39
Location: spring branch, tx
|
| Posted: Mon Aug 03, 2009 3:20 am Post subject: upper and lower elevator horn doubler location |
|
|
Lee
I believe you are correct..
Floyd Wilkes
do not archive
---
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
_________________
Floyd Wilkes |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
