 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
aussiech650
Joined: 04 Oct 2009
Posts: 25
Location: Sydney, Australia
|
 Posted: Sun Oct 04, 2009 3:01 pm Post subject: Parts that dont fit |
 |
|
I am building a CH650 in Australia and have found that my center wing spar is the wrong angle (XL601) and that the front fuselage side skins are also wrong (a mix of XL601 outer dimensions and CH650 pre drilled holes). As it will take some time for replacement parts to arrive down under, I would be interested to hear from anyone that is further along with the build (either CH650 or late XL601) that may be able to advise of other parts that are not correct so that I may have them all sent to me in one shipment. I believe that there may be an issue with the seat bottom? and maybe the top skin?
Regards,
Greg Cox
Zenith Zodiac CH650, VH-ZDC
Sydney, Australia (Cecil Hills)
Email - greg(at)gas-n-go.com.au
Mobile - 0430002333
Fax - (02) 9823 9977
[quote][b]
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
|
|
| Back to top |
|
 |
z601a(at)anemicaardvark.c
Guest
|
| Posted: Mon Oct 05, 2009 5:23 am Post subject: Parts that dont fit |
|
|
On Sunday 04 October 2009 17:59, Greg Cox wrote:
| Quote: | I am building a CH650 in Australia and have found that my center wing spar
is the wrong angle (XL601) and that the front fuselage side skins are also
wrong (a mix of XL601 outer dimensions and CH650 pre drilled holes). As it
will take some time for replacement parts to arrive down under, I would be
interested to hear from anyone that is further along with the build (either
CH650 or late XL601) that may be able to advise of other parts that are not
correct so that I may have them all sent to me in one shipment. I believe
that there may be an issue with the seat bottom? and maybe the top skin?
|
The seat pan I received isn't as much wrong as it is different and
undocumented. There is a flange added to the outboard side which replaces the
"L" angle shown on the plans.
Someone else reported a flange on the inboard side that replaced the "L" angle
there. That one would bother me, because it allows any "slop" in the location
of the center console to be corrected.
I had a lot of problems with the predrilled holes in the wings not lining up
correctly. I managed to make them fit, but only with difficulty.
--
=============================================
Do not archive.
=============================================
Jim B Belcher
BS, MS Physics, Math, Computer Science
A&P/IA
Retired aerospace technical manager
Mathematics and alcohol do not mix.
Do not drink and derive.
=============================================
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
