Matronics Email Lists :: View topic - Nose wheel nut wrench

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

Nose wheel nut wrench

Matronics Email Lists Forum Index -> RV10-List

View previous topic :: View next topic

Author Message

Mike Whisky

Joined: 05 Jun 2006
Posts: 336
Location: Switzerland

Posted: Fri Nov 20, 2009 12:19 pm Post subject: Nose wheel nut wrench

Where can I get this large wrench used to torque the nose wheel nut?



Best

Michael

_________________
RV-10 builder (flying)
#511

jeff(at)westcottpress.com
Guest

Posted: Fri Nov 20, 2009 12:44 pm Post subject: Nose wheel nut wrench

David McNeill makes a nice one...

On Nov 20, 2009, at 12:19 PM, Michael Wellenzohn wrote:



 	  Quote: 	
		   

 >



 Where can I get this large wrench used to tie the nose wheel nut?



 Best

 Michael



 --------

 RV-10 builder (avionics, wiring)

 #511





 Read this topic online here:



 http://forums.matronics.com/viewtopic.php?p 73987#273987

dlm46007(at)cox.net
Guest

Posted: Fri Nov 20, 2009 2:14 pm Post subject: Nose wheel nut wrench

Water pump pliers 



--

jesse(at)saintaviation.co
Guest

Posted: Fri Nov 20, 2009 2:49 pm Post subject: Nose wheel nut wrench

Big channel locks with duct tape on the teeth.



Do not archive.



Jesse Saint

Saint Aviation

jesse(at)saintaviation.com

352-427-0285



Sent from my iPhone



On Nov 20, 2009, at 5:13 PM, "David McNeill" <dlm46007(at)cox.net> wrote:



[quote] 



 Water pump pliers



 --

ricksked(at)embarqmail.co
Guest

Posted: Fri Nov 20, 2009 3:01 pm Post subject: Nose wheel nut wrench

Silly me...I went to Sears and bought the socket.....duh...   ;'

Sent via BlackBerry by AT&T



--

partner14

Joined: 12 Jan 2008
Posts: 540
Location: Granbury Texas

Posted: Fri Nov 20, 2009 3:04 pm Post subject: Nose wheel nut wrench

For those of you not to this point yet... do yourselves a favor and drill a 2nd hole through the front axle.... if you don't you will almost always end up with too little torque or too much.  Because of the nut and use of cotter pin, we are limited to 60 degrees, 1/6th turn to get it right.  Drilling a 2nd hole, you can at least get closer to optimum (30 degrees, 1/12th of a turn.

 Don McDonald



--- On Fri, 11/20/09, David McNeill <dlm46007(at)cox.net> wrote:



 [quote]

From: David McNeill <dlm46007(at)cox.net>

Subject: RE: Nose wheel nut wrench

To: rv10-list(at)matronics.com

Date: Friday, November 20, 2009, 2:13 PM



 --> RV10-List message posted by: "David McNeill" <dlm46007(at)cox.net (dlm46007(at)cox.net)>



Water pump pliers 



--

_________________
Don A. McDonald
40636

partner14

Joined: 12 Jan 2008
Posts: 540
Location: Granbury Texas

Posted: Fri Nov 20, 2009 3:06 pm Post subject: Nose wheel nut wrench

Does the duct tape go on your teeth because you're tightening so much?



--- On Fri, 11/20/09, Jesse Saint <jesse(at)saintaviation.com> wrote:

 [quote]

From: Jesse Saint <jesse(at)saintaviation.com>

Subject: Re: Nose wheel nut wrench

To: "rv10-list(at)matronics.com" <rv10-list(at)matronics.com>

Date: Friday, November 20, 2009, 2:48 PM



 --> RV10-List message posted by: Jesse Saint <jesse(at)saintaviation.com (jesse(at)saintaviation.com)>



Big channel locks with duct tape on the teeth.



Do not archive.



Jesse Saint

Saint Aviation

jesse(at)saintaviation.com (jesse(at)saintaviation.com)

352-427-0285



Sent from my iPhone



On Nov 20, 2009, at 5:13 PM, "David McNeill" <dlm46007(at)cox.net (dlm46007(at)cox.net)> wrote:



[quote] --> RV10-List message posted by: "David McNeill" <dlm46007(at)cox.net (dlm46007(at)cox.net)>



 Water pump  pliers



 --

_________________
Don A. McDonald
40636

Strasnuts

Joined: 10 Feb 2009
Posts: 502
Location: Salt Lake City, UT

Posted: Fri Nov 20, 2009 3:19 pm Post subject: Nose wheel nut wrench

no.  It goes on your wife's mouth for obvious  reasons.

 [quote]   ---

_________________
40936
RV-10 SB N801VR Flying
780 Hours
SuperSTOL 60 hours

Tim Olson

Joined: 25 Jan 2007
Posts: 2872

Posted: Fri Nov 20, 2009 3:20 pm Post subject: Nose wheel nut wrench

 yeah and for the wheel axles with extensions I went to the farm  

store and bought a "bigass" combination wrench and cut it in half for  

easier maneuvering.  Gotta love them tools.



BTW: harbor freight has a flyer out with the infared laser thermometer  

on sale for under $30.  When you need one they're awesome.

Tim

Do not archive



On Nov 20, 2009, at 4:57 PM, ricksked(at)embarqmail.com wrote:



[quote] 



 Silly me...I went to Sears and bought the socket.....duh...   ;'

 Sent via BlackBerry by AT&T



 --

ricksked(at)embarqmail.co
Guest

Posted: Fri Nov 20, 2009 3:44 pm Post subject: Nose wheel nut wrench

Lol...if you have a wife I hope her sense of humor is as good as your response....I've known a few women in my time that liked duct tape...but never on their mouths...wouldn't hold up very long!!! 

Sent via BlackBerry by AT&T



--

jeff(at)westcottpress.com
Guest

Posted: Fri Nov 20, 2009 4:22 pm Post subject: Nose wheel nut wrench

.. sorry, I got my David McNeills and Don McDonalds confused... (I've  

been talking to both of them lately).  Don McDonald gave me a very  

nice wrench.

On Nov 20, 2009, at 12:19 PM, Michael Wellenzohn wrote:



 	  Quote: 	
		   

 >



 Where can I get this large wrench used to tie the nose wheel nut?



 Best

 Michael



 --------

 RV-10 builder (avionics, wiring)

 #511





 Read this topic online here:



 http://forums.matronics.com/viewtopic.php?p 73987#273987

partner14

Joined: 12 Jan 2008
Posts: 540
Location: Granbury Texas

Posted: Fri Nov 20, 2009 4:56 pm Post subject: Nose wheel nut wrench

Hey, wait a minute, Rick and Deems have met my wife.... they know she doesn't need the tape.... on the other hand, me, maybe.

 Don



--- On Fri, 11/20/09, Seano <sean(at)braunandco.com> wrote:



 [quote]

From: Seano <sean(at)braunandco.com>

Subject: Re: Nose wheel nut wrench

To: rv10-list(at)matronics.com

Date: Friday, November 20, 2009, 3:13 PM



    no.  It goes on your wife's mouth for obvious reasons.

 [quote] ---

_________________
Don A. McDonald
40636

partner14

Joined: 12 Jan 2008
Posts: 540
Location: Granbury Texas

Posted: Fri Nov 20, 2009 5:00 pm Post subject: Nose wheel nut wrench

Jeff, you mean that wrench I gave you fits the main gear nuts and the front axle nut????  Shucks, if I'd known that I would have charged you twice as much!  Wait, 2 times 0.... is still 0....  I can't win.

 Don



--- On Fri, 11/20/09, Jeff Carpenter <jeff(at)westcottpress.com> wrote:



  	  Quote: 	
		  

From: Jeff Carpenter <jeff(at)westcottpress.com>

Subject: Re: Nose wheel nut wrench

To: rv10-list(at)matronics.com

Date: Friday, November 20, 2009, 4:09 PM



 --> RV10-List message posted by: Jeff Carpenter <jeff(at)westcottpress.com (jeff(at)westcottpress.com)>



... sorry, I got my David McNeills and Don McDonalds confused... (I've  

been talking to both of them lately).  Don McDonald gave me a very  

nice wrench.

On Nov 20, 2009, at 12:19 PM, Michael Wellenzohn wrote:



 	  Quote: 	
		   --> RV10-List message posted by: "Michael Wellenzohn" <rv-10(at)wellenzohn.net (rv-10(at)wellenzohn.net) 

 >



 Where can I get this large wrench used to tie the nose wheel nut?



 Best

 Michael



 --------

 RV-10 builder (avionics, wiring)

 #511





 Read this topic online  here:



 http://forums.matronics.com/viewtopic.php?p=273987#273987



http://www.matronics.com/contrinbsp;               -Matt Dralle, List Asp;  --> http://f=======================


	




	


         [quote][b]

_________________
Don A. McDonald
40636

rv10builder(at)verizon.ne
Guest

Posted: Fri Nov 20, 2009 6:59 pm Post subject: Nose wheel nut wrench

Great idea Don! It may be easier to drill the hole in the nut  however.

 P

  



  From: Don McDonald (building_partner(at)yahoo.com) 

 Sent: Friday, November 20, 2009 3:00 PM

 To: rv10-list(at)matronics.com (rv10-list(at)matronics.com) 

 Subject: RE: Nose wheel nut wrench

 



                   For those of you not to this point yet.... do yourselves a favor and        drill a 2nd hole through the front axle.... if you don't you will almost        always end up with too little torque or too much.  Because of the nut        and use of cotter pin, we are limited to 60 degrees, 1/6th turn to get it        right.  Drilling a 2nd hole, you can at least get closer to optimum        (30 degrees, 1/12th of a turn.

       Don McDonald



--- On Fri, 11/20/09, David McNeill        <dlm46007(at)cox.net> wrote:



       [quote]

From:          David McNeill <dlm46007(at)cox.net>

Subject: RE: Nose          wheel nut wrench

To: rv10-list(at)matronics.com

Date: Friday,          November 20, 2009, 2:13 PM



         --> RV10-List message posted by: "David McNeill"          <dlm46007(at)cox.net (dlm46007(at)cox.net)>



Water          pump pliers 



--

robin1(at)mrmoisture.com
Guest

Posted: Fri Nov 20, 2009 9:19 pm Post subject: Nose wheel nut wrench

It's easy to remember:



Don McDonald had a wrench, E-I-E-I-O



I agree completely with drilling the nut or extra hole concept. We

drilled the nut after finding one was too tight and one was too loose. 



 



The other day I was heading out for my regular commute when  I saw a

friend in his sweet F33 Bonanza in the run up area. We waved and he was

off for his left downwind. I completed my run-up as another two

departures and an arrival proceeded my left downwind. I ended up passing

the F33 at on my way through 8,000' to 9,500'. I was climbing faster and

at a greater rate of climb.  While we were not that close to each other

he did comment that he could see my "shit eating grin." All I could say

is that its an "official RV Shit eating grin" thank you very much and

shit never tasted so good! 



The more I fly the -10 the more I like it. I am not sure if it's the

avionics suite, the comfort or it's utilitarian nature but it is one

terrific airplane.



Keep building and fly safe,



 



Robin



 



From: owner-rv10-list-server(at)matronics.com

[mailto:owner-rv10-list-server(at)matronics.com] On Behalf Of Pascal

Sent: Friday, November 20, 2009 5:57 PM

To: rv10-list(at)matronics.com

Subject: Re: Nose wheel nut wrench



 



Great idea Don! It may be easier to drill the hole in the nut however.



P



 



From: Don McDonald <mailto:building_partner(at)yahoo.com>  



Sent: Friday, November 20, 2009 3:00 PM



To: rv10-list(at)matronics.com 



Subject: RE: Nose wheel nut wrench



 



For those of you not to this point yet.... do yourselves a favor and

drill a 2nd hole through the front axle.... if you don't you will almost

always end up with too little torque or too much.  Because of the nut

and use of cotter pin, we are limited to 60 degrees, 1/6th turn to get

it right.  Drilling a 2nd hole, you can at least get closer to optimum

(30 degrees, 1/12th of a turn.



Don McDonald



--- On Fri, 11/20/09, David McNeill <dlm46007(at)cox.net> wrote:



	

	From: David McNeill <dlm46007(at)cox.net>

	Subject: RE: Nose wheel nut wrench

	To: rv10-list(at)matronics.com

	Date: Friday, November 20, 2009, 2:13 PM



	

<dlm46007(at)cox.net

<http://us.mc537.mail.yahoo.com/mc/compose?to=dlm46007(at)cox.net> >

	

	Water pump pliers 

	

	--

Display posts from previous:

	Matronics Email Lists Forum Index -> RV10-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum