Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Model 4 tail wheel spring

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Kitfox-List
View previous topic :: View next topic  
Author Message
BruceE7837(at)aol.com
Guest





PostPosted: Tue Nov 24, 2009 10:59 am    Post subject: Model 4 tail wheel spring Reply with quote

I'm completing a Model 4 started years ago by someone else. My kit has a single leaf tail wheel spring, and its been suggested that I add a second leaf for safety, should the first leaf break. I'm concerned about the tail spring being too stiff. The single spring is about 3/16 thick, and is already pretty stiff. What does the list think? Bruce Estes
[quote][b]


- The Matronics Kitfox-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List
Back to top
 
sourdostan(at)aol.com
Guest





PostPosted: Tue Nov 24, 2009 11:37 am    Post subject: Model 4 tail wheel spring Reply with quote

Buy the 2-leaf (actually 2 and one-half) from John McBean. My single spring set-up broke and I replaced it with John's, which is doing well and isn't too stiff.

Stan Specht
Model-IV Speedster 1600 hrs.
Lakewood, CO


--


- The Matronics Kitfox-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List
Back to top
 
jareds(at)verizon.net
Guest





PostPosted: Tue Nov 24, 2009 11:55 am    Post subject: Model 4 tail wheel spring Reply with quote

I just ordered a leaf from kfox and they only sell in a complete kit unfortunately. It comes with 3 leafs but the stud on bottom is only long enough for two which is what i have always had and that is a perfect amount of cushion for my model 4. I have had some hard landings and fly in badlands of SD and would not fly with less than 2 springs.
Just my opinion. Also when i had to trailer the fox out recently of a winter wheat field i didnt have a chance to empty the fuel and the weight alone broke the tail spring after only a few bumps on a flatbed trailer.
[quote] ---


- The Matronics Kitfox-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List
Back to top
 
bw12345(at)sbcglobal.net
Guest





PostPosted: Tue Nov 24, 2009 5:53 pm    Post subject: Model 4 tail wheel spring Reply with quote

Who is John McBean and how do you get in touch?

BOB

--- On Tue, 11/24/09, sourdostan(at)aol.com <sourdostan(at)aol.com> wrote:
[quote]
From: sourdostan(at)aol.com <sourdostan(at)aol.com>
Subject: Re: Kitfox-List: Model 4 tail wheel spring
To: kitfox-list(at)matronics.com
Date: Tuesday, November 24, 2009, 2:31 PM

Buy the 2-leaf (actually 2 and one-half) from John McBean. My single spring set-up broke and I replaced it with John's, which is doing well and isn't too stiff.

Stan Specht
Model-IV Speedster 1600 hrs.
Lakewood, CO
--


- The Matronics Kitfox-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List
Back to top
 
MDKitfox(at)aol.com
Guest





PostPosted: Tue Nov 24, 2009 6:17 pm    Post subject: Model 4 tail wheel spring Reply with quote

You can reach John, president of Kitfox, LLC at:
Contact Info
Please contact us...
Quote:
Quote:
123 Airport Way
PO Box 997
Homedale, ID 83628 USA



Rick Weiss
N39RW Series V Speedster, 912ULS
SkyStar S/N 1
Port Orange, FL


On Nov 24, 2009, at 8:48 PM, Robert Rivard wrote:
[quote]Who is John McBean and how do you get in touch?

BOB

--- On Tue, 11/24/09, sourdostan(at)aol.com (sourdostan(at)aol.com) <sourdostan(at)aol.com (sourdostan(at)aol.com)> wrote:
[quote]
From: sourdostan(at)aol.com (sourdostan(at)aol.com) <sourdostan(at)aol.com (sourdostan(at)aol.com)>
Subject: Re: Kitfox-List: Model 4 tail wheel spring
To: kitfox-list(at)matronics.com (kitfox-list(at)matronics.com)
Date: Tuesday, November 24, 2009, 2:31 PM

Buy the 2-leaf (actually 2 and one-half) from John McBean. My single spring set-up broke and I replaced it with John's, which is doing well and isn't too stiff.

Stan Specht
Model-IV Speedster 1600 hrs.
Lakewood, CO
--


- The Matronics Kitfox-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List
Back to top
 
Lynn Matteson



Joined: 10 Jan 2006
Posts: 2778
Location: Grass Lake, Michigan

PostPosted: Wed Nov 25, 2009 6:00 am    Post subject: Model 4 tail wheel spring Reply with quote

Ditto what Stan said...if it's good enough for Stan "the man", it's
good enough for me. : )

Actually I modified my "half-spring" by shortening it to soften the
ride a bit. It wasn't quite enough softening, so the next time I have
the notion, I'll cut a little bit more off the length of the half-
spring/ helper spring/ booster spring....whatever it's called.

Lynn Matteson
Kitfox IV Speedster, taildragger
Jabiru 2200, #2062, 814.7 hrs
Countdown to 1000 hrs~185 to go
Sensenich 62"x46" Wood prop
Electroair direct-fire ignition system
Rotec TBI-40 injection
Status: flying (and learning)
On Nov 24, 2009, at 2:31 PM, sourdostan(at)aol.com wrote:

[quote] Buy the 2-leaf (actually 2 and one-half) from John McBean. My
single spring set-up broke and I replaced it with John's, which is
doing well and isn't too stiff.

Stan Specht
Model-IV Speedster 1600 hrs.
Lakewood, CO
--


- The Matronics Kitfox-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List

_________________
Lynn
Kitfox IV-Jabiru 2200
N369LM
Back to top
View user's profile Send private message Send e-mail  
Pat Reilly



Joined: 06 Aug 2009
Posts: 345

PostPosted: Wed Nov 25, 2009 7:43 am    Post subject: Model 4 tail wheel spring Reply with quote

Bob, John McBean owns what used to be Kitfox. Google up Kitfox and you will see the link to his store and ph#. I also have his 3 leak spring. I used only the�2 full length leaves. I rearched them to get proper castor angle on my tail wheel. I also had the 1 piece aluminum bar they called a "spring". I sold it to someone that wanted to use what was originally supplied with his plane even though they appear to be�junk in my mind.

Hey guys airworthy inspection scheduled for 1 week from tomorrow!

Pat Reilly
Mod 3 582�Rebuild
Rockford, IL
On Tue, Nov 24, 2009 at 7:48 PM, Robert Rivard <bw12345(at)sbcglobal.net (bw12345(at)sbcglobal.net)> wrote:
[quote] Who is John McBean and how do you get in touch?

BOB

--- On Tue, 11/24/09, sourdostan(at)aol.com (sourdostan(at)aol.com) <sourdostan(at)aol.com (sourdostan(at)aol.com)> wrote:
[quote]
From: sourdostan(at)aol.com (sourdostan(at)aol.com) <sourdostan(at)aol.com (sourdostan(at)aol.com)>
Subject: Re: Kitfox-List: Model 4 tail wheel spring
To: kitfox-list(at)matronics.com (kitfox-list(at)matronics.com)
Date: Tuesday, November 24, 2009, 2:31 PM

Buy the 2-leaf (actually 2 and one-half) from John McBean. �My single spring set-up broke and I replaced it with John's, which is doing well and isn't too stiff.

Stan Specht
Model-IV Speedster 1600 hrs.
Lakewood, CO
--


- The Matronics Kitfox-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List
Back to top
View user's profile Send private message Send e-mail  
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Kitfox-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group