Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Band Clamps

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Europa-List
View previous topic :: View next topic  
Author Message
MJKTuck(at)cs.com
Guest
PostPosted: Fri Jun 11, 2010 10:08 am    Post subject: Band Clamps Reply with quote
Hi Folks,

I am forever having trouble keeping the exhaust heat shield located
using the 6 inch worm drive band clamps. I tighten hem up as hard as I
can but they expand with the heat and vibrate off.

I'm looking for a source of the type of clamp found on the Rotax oil
tank holding the two halves together (except with a plain band not a
v-section) that you do up then close tighter with a mechanical lever.

Any ideas?

Martin Tuck
Europa N152MT
Wichita, Kansas

- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
rparigoris



Joined: 24 Nov 2009
Posts: 791
PostPosted: Fri Jun 11, 2010 10:38 am    Post subject: Band Clamps Reply with quote
Hi MartinI am unfamiliar clamps that hold on 912/s heat shields (have a 914). You may want to have a look at www.mcmaster.com for some ideas.Ron Parigoris [quote][b]

- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
View user's profile Send private message
keithhickling(at)clear.ne
Guest
PostPosted: Sat Jun 12, 2010 4:42 pm    Post subject: Band Clamps Reply with quote
Quote:
Hi Martin,
Europa recently issued a SB recommending lockwiring of the clamps for this

reason. I did mine and found that they had become very loose after 40 hours.
Now still fine after 120 hours. The lockwiring is a bit fiddley but not too
difficult.

Regards,
Keith Hickling.
XS 613, 912uls, Airmaster.


Quote:
"I am forever having trouble keeping the exhaust heat shield located using
the 6 inch worm drive band clamps. I tighten hem up as hard as I can but
they expand with the heat and vibrate off."




- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
gavanne(at)iconz.co.nz
Guest
PostPosted: Sat Jun 12, 2010 4:50 pm    Post subject: Band Clamps Reply with quote
Take them off and get rid of the heat shield, not really needed and excess
weight

Gavin Lee
ZK-EPA

--

- The Matronics Europa-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Europa-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group