Matronics Email Lists :: View topic - bringing Pitot and static tubes into fuselage

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

bringing Pitot and static tubes into fuselage

Matronics Email Lists Forum Index -> Europa-List

View previous topic :: View next topic

Author Message

graeme bird

Joined: 15 Jul 2010
Posts: 434

Posted: Thu Oct 21, 2010 12:26 am Post subject: bringing Pitot and static tubes into fuselage

Advice sort on the best place to bring the pitot and static lines (plus strobes) into the fuselage from the port wing. Concerned about reducing structural strength at the wrong point. Am tempted to bring in way back near the flap control rod opening as is tidy for the cockpit.

- The Matronics Europa-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List

_________________
Graeme Bird
kit4 (Wagstaff) TBD
Kit3 G-CLXU (Gregory) mono 914 xs Woodcomp
Kit2 G-PATS - (kesterton) Mono Classic 912 warpdrive
Kit 1 G-UMPY - Mono Classic/XS 912S, Woodcomp G(@)gdbmk.co.uk

graeme bird

Joined: 15 Jul 2010
Posts: 434

Posted: Wed Oct 27, 2010 12:35 pm Post subject: Re: bringing Pitot and static tubes into fuselage

I didnt get any response on this, was it a stupid question? I still cant find out where they are supposed to come through.



Advice appreciated.

- The Matronics Europa-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List

rlborger(at)mac.com
Guest

Posted: Wed Oct 27, 2010 1:17 pm Post subject: bringing Pitot and static tubes into fuselage

Graeme,



I understand there is no specific direction for the routing and exit of the pitot/static plumbing.  It's pretty much what ever works best for you.



Check six,

Bob Borger

http://www.europaowners.org/N914XL

Europa XS, Short Wing, Intercooled Rotax 914

rlborger(at)mac.com

Cel: 817-992-1117





On Oct 27, 2010, at 3:35 PM, graeme bird wrote:



 	  Quote: 	
		   

 

 I didnt get any response on this, was it a stupid question? I still cant find out where they are supposed to come through.

 

 Advice appreciated.

 

 --------

 Graeme Bird

- The Matronics Europa-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List

rparigoris

Joined: 24 Nov 2009
Posts: 792

Posted: Wed Oct 27, 2010 1:58 pm Post subject: Re: bringing Pitot and static tubes into fuselage

Hi Graeme



You can look through this album for some ideas:

http://www.europaowners.org/forums/gallery2.php?g2_itemId=31838



Ira and Bobs routing are at the beginning.



My choice is scattered about the album a bit, but I ran 3 pneumatic hoses and wires on the port side and 1 pneumatic hose and wires on the starboard side.



They are just aft of the spars and sneak between the fuse and the fuel tank and poke out through the space between the headrest and fuse side.



Since I needed to get some of the port wires to the starboard headrest, I covered the wires with Teflon expando sleeve and snaked it above the fuel tank to the inside of the starboard headrest.



I considered the aft route, but couldn't make it work as well for me . If you do consider the aft route keep in mind weakening it may cause the rear liftpin socket.



Good luck

Ron Parigoris



Stbd 1 pneumatic hose and the other is for wires:

http://www.europaowners.org/forums/gallery2.php?g2_itemId=84429



Port 3 pneumatic:

http://www.europaowners.org/forums/gallery2.php?g2_itemId=84432



Port exiting between headrest and fuse:

http://www.europaowners.org/forums/gallery2.php?g2_itemId=31871

- The Matronics Europa-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List

jan_de_jong(at)casema.nl
Guest

Posted: Wed Oct 27, 2010 3:45 pm Post subject: bringing Pitot and static tubes into fuselage

This is still in the future for me, but I think my plan is:

- from wing conduit outlet behind the spar over the spar (under fairing) 

to in front of spar

- connections in front of spar

- into fuselage behind seat

- up to window sill by headrest avoiding motorglider wings spoiler 

actuator hole in the corner (fuselage side just below spar pin hole)

- join window sill conduit

I have the impression that this was once considered the standard way. It 

may be in the manual somewhere.

Jan de Jong



graeme bird wrote:

 	  Quote: 	
		   



 I didnt get any response on this, was it a stupid question? I still cant find out where they are supposed to come through.



 Advice appreciated.

- The Matronics Europa-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List

jrgowing(at)bigpond.net.a
Guest

Posted: Wed Oct 27, 2010 3:45 pm Post subject: bringing Pitot and static tubes into fuselage

Graeme

I placed my tube into the fuselage rear of the fuselage stiffener.  Holding the tube in place alongside the stiffener, I added a cover rising to just under the fuselage side stiffener (door sill) of the fuselage where I made a triangular support for the sill which is also a tunnel for wiring and tubes which can go either way……

JR Kit 327 in OZ

 

Do not archive

From: owner-europa-list-server(at)matronics.com [mailto:owner-europa-list-server(at)matronics.com] On Behalf Of graeme bird

Sent: Thursday, 28 October 2010 7:35 AM

To: europa-list(at)matronics.com

Subject: Re: bringing Pitot and static tubes into fuselage

 

--> Europa-List message posted by: "graeme bird" <graeme(at)gdbmk.co.uk (graeme(at)gdbmk.co.uk)>



I didnt get any response on this, was it a stupid question? I still cant find out where they are supposed to come through.



Advice appreciated.



--------

Graeme Bird





Read this topic online here:



http://forums.matronics.com/viewtopic.php?p=317245#317245

http://www.matron--> http://forums.matronics.com

_p;         - List Contribution bsp;                    -Matt Dralle, List href="http://www.matronics.com/contribution">http://www.matronics.com/c=================





No virus found in this message.

Checked by AVG - www.avg.com

Version: 10.0.1152 / 10/26/10

  [quote][b]

- The Matronics Europa-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List

europa471

Joined: 08 Apr 2009
Posts: 35

Posted: Wed Oct 27, 2010 4:46 pm Post subject: bringing Pitot and static tubes into fuselage

Graeme



Attached (I hope)  is a page from what I believe was the final ¨Europa 

News¨ from the old Company.



Regards



Lance Sandford in OZ

 	  Quote: 	
		   



 I didnt get any response on this, was it a stupid question? I still cant find out where they are supposed to come through.



 Advice appreciated.



 --------

 Graeme Bird

- The Matronics Europa-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List

pitot_static_entry_holes.jpeg

Description:

Filesize:

60.43 KB

Viewed:

5362 Time(s)

Ivor Phillips

Joined: 16 Jan 2006
Posts: 253
Location: London UK

Posted: Thu Oct 28, 2010 1:55 am Post subject: bringing Pitot and static tubes into fuselage

Hi Graeme 

If you follow the workshop manual then the entry points for the Pitot/Static tube 

Are self explanatory, A gentle curve to the front of the spar with entry between the spar and  forward pins,  It will be well away from any hard points,  

  

Regards 

Ivor 

  

  

  

  

  

  

  

Pitot/static tube 

Drill two 1/4” diameter holes through the port fuselage side midway between the forward wing  

socket and the spar opening, making sure to keep them away from the seat belt mounting. These  

holes are for the pitot/static tubes. 

When rigging the aircraft the tubes will be led over the top of the spar tang 

Page 27 - 22 Issue 2 Europa Build Manual

 On 27 October 2010 21:35, graeme bird <graeme(at)gdbmk.co.uk (graeme(at)gdbmk.co.uk)> wrote:

 [quote]--> Europa-List message posted by: "graeme bird" <graeme(at)gdbmk.co.uk (graeme(at)gdbmk.co.uk)>

 

I didnt get any response on this, was it a stupid question? I still cant find out where they are supposed to come through.



Advice appreciated.



--------

Graeme Bird





Read this topic online here:

 

http://forums.matronics.com/viewtopic.php?p=317245#317========================

 y Browse, Chat, FAQ,

 ="http://www.matronics.com/Navigator?Europa-List" target="_blank">http:=====

  http://forums.mle, List Admin.

 =====



[b]

- The Matronics Europa-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Europa-List

Display posts from previous:

	Matronics Email Lists Forum Index -> Europa-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum