 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
Peter Laurence
Joined: 10 Jan 2006
Posts: 50
|
 Posted: Mon May 08, 2006 7:21 am Post subject: aileron push tubes |
 |
|
Question for those of you that have installed the Stick to aileron bellcrank
push tubes.
Did you cut them as per Van's measurments before installing. If so, were the
measurments correct or were you "VANdalized"?
Peter Laurence
9A fuse
| | - The Matronics RV9-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV9-List |
|
|
|
| Back to top |
|
 |
Neilekins(at)aol.com
Guest
|
| Posted: Mon May 08, 2006 7:35 am Post subject: aileron push tubes |
|
|
I cut them as per plans. I would add 1/4 inch to them. I had just enough
length for minimum amount threads to screw in..That was after I put the proper
angle of deflection. You can check out my web site. neilsplane.com Im
building a lancair esp now...Neil
| | - The Matronics RV9-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV9-List |
|
|
|
| Back to top |
|
|
jc(at)INFONET.COM.BR
Guest
|
| Posted: Mon May 08, 2006 8:15 am Post subject: aileron push tubes |
|
|
Ive cutted them by Vans manual with any problems. To centralize the sticks Ive got
some difficult. Some trials and errors using an plumb bob in both sticks. One hour job.
To install the washers between the sticks and bell crank it is etter to buy washer tool
at Avery.
PU-JCI
RV-9A
Flying 125 hs
JC - Aracaju - Brasil
websites.expercraft.com/jcmm
| | - The Matronics RV9-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV9-List |
|
|
|
| Back to top |
|
|
Peter Laurence
Joined: 10 Jan 2006
Posts: 50
|
| Posted: Mon May 08, 2006 9:31 am Post subject: aileron push tubes |
|
|
Thanks Neil
I'm from Tampsa. Where are you located/
Peter
(A fuse
---
| | - The Matronics RV9-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV9-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
