Matronics Email Lists :: View topic - Problem with upper front strut fitting

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

Problem with upper front strut fitting

Matronics Email Lists Forum Index -> Zenith701801-List

View previous topic :: View next topic

Author Message

robert.eli(at)comcast.net
Guest

Posted: Sun Nov 28, 2010 7:50 am Post subject: Problem with upper front strut fitting

Folks,

  

 Construction on my 701 has gone slowly but steadily  since 2003, with no major problems until now.  I am building from the full  kit purchased in the fall of 2003. I am currently working on the right wing  skins, following the current version of the photo assembly guide. I am at the  point where I am attempting to install the 7V8-4SP strut angle (it is mislabeled  as 7V8-3SP in the upper photo in Section 4A, page 9 of 12, wing nose skin). My  first hint of a problem was that the location of the cutout for the 7V2-5 front  upper strut fitting in the nose skin was located too far toward the wing tip to  match my required location. I needed to shift the location by about 10 mm toward  nose rib #4, which I did. After installing the nose skin and bolting the strut  fitting in place, I discovered that the 7V8-4SP strut angle would not fit under  the 7V2-5 strut fitting as shown in the attached photo.

  

 The source of the problem was that the spar web  doubler and associated strut angle 7V2-4 assembly was installed so that the  outboard edge of the web doubler is at station 2255 instead of at 2260 as  specified on drawing 7-V-2. This effectively places the entire assembly 5 mm  closer to the wing root than it should be. This assembly was done by Zenith. All  other measures are OK, including rib station locations and the angle of the  strut fitting. I hope there is a way to salvage things without trashing my  entire wing assembly.

  

 As anybody out there encountered a similar problem,  and if so, what was the fix?

  

 Help!

  

 Bob Eli

 N701K

- The Matronics Zenith701801-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith701801-List

IMG_0535.JPG

Description:

Filesize:

1.23 MB

Viewed:

8017 Time(s)

Geoff Heap

Joined: 12 Jan 2006
Posts: 266
Location: Lindenwold, New Jersey

Posted: Mon Nov 29, 2010 5:16 am Post subject: Re: Problem with upper front strut fitting

Hi Bob. Ive got a couple of ideas. However. This is a wing attach point. You really need to discuss the fix with Zenith. Don't despair yet. It looks like it can be worked around....Geoff

- The Matronics Zenith701801-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith701801-List

_________________
Dual controls. Dynon 180. Icom 210 Garmin 296. Becker transponder. Sigtronics intercom. Electric flaperons.

robert.eli(at)comcast.net
Guest

Posted: Mon Nov 29, 2010 6:44 am Post subject: Problem with upper front strut fitting

Geoff,



Thanks for the reply, Gordon also responded with a similar problem to mine. 

The solution was to add an 1/8 inch shim between 7V2-4 and -5. I am 

contacting Zenith this morning to see what they say.



Bob Eli



---

- The Matronics Zenith701801-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith701801-List

bryanekholm

Joined: 16 May 2007
Posts: 25
Location: Minnesota

Posted: Fri Dec 03, 2010 12:48 pm Post subject: Re: Problem with upper front strut fitting

It also looks like you will have to cut a notch in the L piece so that it can be moved outboard to align its rivet line with the rib centerline.  



Bryan Ekholm

- The Matronics Zenith701801-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith701801-List

_________________
Bryan Ekholm

robert.eli(at)comcast.net
Guest

Posted: Fri Dec 03, 2010 2:05 pm Post subject: Problem with upper front strut fitting

Bryan,



I was originally planning to notch the L, but I got a response from Gordon 

Lysle who had a similar problem with an improperly located web doubler 

assembly, resulting in the mislocation of the strut fitting. He checked with 

Zenith to see if it was OK to shim the strut fitting (using a 1/8 in. thick 

shim) so as to raise it up some and also shift it in the outboard direction. 

Zenith OK'd this and supplied some shim material and longer bolts (to deal 

with the increase in grip length). I also contacted Zenith, and they OK'd 

the same fix. I just received the shim material and bolts today.



I don't like the shim fix, but it does avoid the need to notch the L (and 

also shave the strut doubler flange)  in order to get everything to match 

up. All of this raises another question for which I have not had an answer. 

How much "out-of-position" can the strut fitting be without having 

misalignment problems when attaching the struts? With the shim, the strut 

fitting will protrude a little more than it normally would from the nose 

skin opening, however the proper angle will be maintained. If I were to go 

the notch route, leaving the strut attachment as is, then the fitting  would 

be shifted about 5 mm inboard from where it should be.



Bob Eli

---

- The Matronics Zenith701801-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith701801-List

ruruny(at)aol.com
Guest

Posted: Sat Dec 04, 2010 12:08 pm Post subject: Problem with upper front strut fitting

.......How much "out-of-position" can the strut fitting be without having 

        misalignment problems when attaching the struts?

    

   Bob,

    

   Not a problem at all. The shim fix will get the strut fitting very close if not right where it should be.

   The angle is exactly the same, if it protrudes a little bit further that is not a problem if you have

   the 2 piece struts. Lots of room to work with here. If you have one piece struts they still might work fine.

   I had one piece and had angle problems with the ends. I cut off the wing end of each strut. Zenith sent the

   ends. I bolted the ends of the struts to their points, set the wing angle and then drilled the holes for the

   bolts that hold the 2 pieces together. I remember shaving the strut doubler flange and the L anyway to get

   a nice fit when installing these parts.(http://www.701builder.com/02WingSkins6.htm) . 

    

   Brian

    

   [quote][b]

- The Matronics Zenith701801-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith701801-List

robert.eli(at)comcast.net
Guest

Posted: Sun Dec 05, 2010 5:37 am Post subject: Problem with upper front strut fitting

Brian,

  

 Thanks for your response. This is the reassurance  that I needed. I just checked the fit with the new shim yesterday, and the L  will fit under the strut fitting, but is in slight contact at the forward  corner. Therefore I will also shave the L flange, but will only need to remove  about 1 or 2 mm. The strut doubler flange will also need to be shaved by a small  amount in order to mate simultaneously with the  strut fitting and the  L. I was pretty sure that the strut assembly could be made to work with the  shimmed strut fitting, but it is good to get that confirmation from you. I am  going to drill the holes and complete the assembly later today.

  

 Thanks

  

 Bob

 N701K

 [quote]   ---

- The Matronics Zenith701801-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith701801-List

ruruny(at)aol.com
Guest

Posted: Sun Dec 05, 2010 8:34 am Post subject: Problem with upper front strut fitting

.......I am going to drill the holes and complete the 

 assembly later today

    

   Bob,

    

   Just a tip to make life easier, when your ready to drill, tape and clamp everything in place to its proper

   position. Drill and cleco the L first to the skin and rib. Drill and cleco only the 2 end holes of the L and strut doubler.

   Take it off the wing and drill the rest of the holes for the strut doubler and L on the edge of your work bench.

   Rivet them together before you rivet it to the wing, you will be thankful for this as its a tight squeeze for the

   riveter. Eventually, you will want to pilot drill the strut end, the upper strut fitting and doubler all together not separately.

   This is because you are going to use a hand drill for this and have to get it close to 90 deg as possible. Make sure to

   tape a piece of scrap aluminum on the skin where the drill bit comes out as it will hit the skin and damage it if the

   scrap is not there. The nice part of the 2 piece struts you can do this now with the small strut piece

   right side up on the bench which is easier... or later upside down while installing your wings(harder).

   The wing diehedral adjustment is made between the small and the large strut peices, set and drilled.

   With the one piece struts the wing diehedral is set and then drill the end holes to lock it in.

   I suspect you have the one piece circa 2003 kit.

    

   Brian

 

 

   [quote][b]

- The Matronics Zenith701801-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith701801-List

robert.eli(at)comcast.net
Guest

Posted: Mon Dec 06, 2010 6:49 am Post subject: Problem with upper front strut fitting

Brian,

  

 You have confirmed what I had already decided to do  with regard to drilling the strut doubler to L holes off the wing. Also, I  agree that the riveting will be a lot more difficult to do correctly with  the assembly clecoed to the wing, so I plan to follow your recommendation. When  I first read your Email earlier, I had no idea that there were two  types of struts. I have confirmed that I have the old single piece struts with  the attach fittings welded on each end. I have both my old original  drawings from 2003, and also an updated version from Fall of 2009. I now  see what you are talking about with regard to the two piece struts, since I have  that version shown on the new drawings. Reading ahead to Tommy's offer of  the "strut ends", I assume he is refering to the short end of  the new two piece struts? Am I correct in assuming it is possible to modify  my old struts to the new configuration, if I have the short strut end? If so, I  assume from what you are saying that the strut attachment process and  adjustment is a lot easier with the two piece struts.

  

 Bob

  

  

 [quote]   ---

- The Matronics Zenith701801-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith701801-List

Display posts from previous:

	Matronics Email Lists Forum Index -> Zenith701801-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum