Matronics Email Lists :: View topic

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

Wing Tank Fitting

Matronics Email Lists Forum Index -> Kitfox-List

View previous topic :: View next topic

Author Message

aviateer

Joined: 08 Aug 2008
Posts: 23

Posted: Sun Feb 13, 2011 1:06 pm Post subject: Wing Tank Fitting

Hello Fellow Kitfox Drivers,

  

 I re-sloshed my wing tanks last summer. I had to cut off the old brass elbow fitting with a dremel tool so I could  get the finger strainer out. Now I have been looking to get the whole assembly back together. I cannot seem to find a swivel fitting that will allow me to use the original finger strainer (3/8 NPT). I need a 1/4 NPT male swivel 90 degree low profile. Or some sort of banjo fitting (already tried the ANDAIR BANJO FITTING FML 1/4"). This is too long. I only have 1.25" from the wing tank to the inside of the first rib. What are the rest of you guys using after the tank have been installed?

   

  

 Thanks,

  

  

 Kirk

  

 N198KM

  [quote][b]

- The Matronics Kitfox-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List

Tom Jones

Joined: 12 Mar 2006
Posts: 752
Location: Ellensburg, WA

Posted: Sun Feb 13, 2011 1:42 pm Post subject: Re: Wing Tank Fitting

Kirk, my kit came with a straight fitting to attach to the finger strainer.  The manual says to notch the rib to clear the fitting and fuel line.  You will probably have to notch the butt rib also.  picture attached.

- The Matronics Kitfox-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List

Tank fitting.jpg

Description:

Filesize:

47.92 KB

Viewed:

4280 Time(s)

_________________
Tom Jones
Classic IV
503 Rotax, 72 inch Two blade Warp
Ellensburg, WA

valleyairport(at)cotterwe
Guest

Posted: Sun Feb 13, 2011 1:52 pm Post subject: Wing Tank Fitting

Kirk,

              You can use a street elbow in the finger strainer pointed  whichever way you want then put a straight male fitting in the elbow. Worked for  me. Available at your local hardware store.

  

 Jay

 S-6 290-D2  Lyc.       AR.

 [quote]   ---

- The Matronics Kitfox-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List

lcfitt(at)sbcglobal.net
Guest

Posted: Sun Feb 13, 2011 3:54 pm Post subject: Wing Tank Fitting

Kirk,

  

 Interesting problem and parallels ours exactly.  I  am helping a friend finish  a previously started Model V with the center  wing tank ports.   The previous builder had done some interesting  things, which included an electric fuel gauge which required, at least in his  mind covering most of the first rib with thin plywood which seriously limits  access.  He then mounted a half inch bushing which he glued into the  tank, then a 3/8" finger strainer with integral straight hose barb.  There  was no way to attach hose to the hose barb and fold the wings, or unfold them,  for that matter.

  

 What came of it is a polycarbonate doubler glued to the  bottom fabric in the area of the outlet, then cutting the fabric and removing  the threaded parts one by one and after some hairy moments finally got the large  bushing out without damaging the tanks.  I got the larger finger strainers  and as you find, discovered that there is not the ideal elbow fitting out there  in the real world.  I did find a couple of 5/16" hose low profile elbows,  but they were in 1/4" thread size and there was absolutely no room for another  bushing.  What I finally did is chuck the elbow in a lathe and cut off the  threads, then chuck a 3/8" bushing in the lathe and bore a hole to math the  thread free elbow and sweat solder them together.  We now have a low  profile elbow with threads that match the finger strainer.  Thinking about  it, I realize I will have to modify a wrench if we ever want to remove the  hardware to check the finger strainer.  Picture attached.

  

 Let me know if I can help.

  

 Lowell

  



  From: Kitfoxkirk (aviateer(at)gmail.com) 

 Sent: Sunday, February 13, 2011 12:59 PM

 To: kitfox-list(at)matronics.com (kitfox-list(at)matronics.com) 

 Subject: Wing Tank Fitting

 



 Hello Fellow Kitfox Drivers,

  

 I re-sloshed my wing tanks last summer. I had to cut off the old brass  elbow fitting with a dremel tool so I could  get the finger strainer out.  Now I have been looking to get the whole assembly back together. I cannot seem  to find a swivel fitting that will allow me to use the original finger strainer  (3/8 NPT). I need a 1/4 NPT male swivel 90 degree low profile. Or some sort of  banjo fitting (already tried the ANDAIR BANJO FITTING FML 1/4"). This is too  long. I only have 1.25" from the wing tank to the inside of the first rib. What  are the rest of you guys using after the tank have been installed?

  

  

 Thanks,

  

  

 Kirk

  

 N198KM

 	  Quote: 	
		  



href="http://www.matronics.com/Navigator?Kitfox-List">http://www.matronhref="http://forums.matronics.com">http://forums.matronics.com

href="http://www.matronics.com/contribution">http://www.matronics.com/c

- The Matronics Kitfox-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List

Fuel_Elbow.jpg

Description:

Filesize:

104.06 KB

Viewed:

4269 Time(s)

Lynn Matteson

Joined: 10 Jan 2006
Posts: 2778
Location: Grass Lake, Michigan

Posted: Mon Feb 14, 2011 3:51 am Post subject: Wing Tank Fitting

My instructions called for making a notch in the rib which I did and  

a straight 1/4 NPT fitting clears the rib perfectly, and screws right  

into the 3/8 NPT finger strainer. About 980 hours on this setup, when  

I decided to add front ports to the tanks (13 gallon original  

Kitfox), which I did by building up the front area with fiberglas,  

drilling and tapping to 3/8 NPT, and installing the usual finger  

strainer and another straight fitting, albeit at a *slight* up-from- 

horizontal angle to clear the rib in that area. Another 100 hours on  

the combined 4-port system, and no problems.



Lynn Matteson

Kitfox IV Speedster, taildragger

Jabiru 2200, #2062

Sensenich 62"x 55.5 Wood (winter) until the Prince prop arrives

Electroair direct-fire ignition system

Rotec TBI-40 injection

Status: flying...1081 hrs (since 3-27-2006)





On Feb 13, 2011, at 3:59 PM, Kitfoxkirk wrote:



 	  Quote: 	
		   Hello Fellow Kitfox Drivers,



 I re-sloshed my wing tanks last summer. I had to cut off the old  

 brass elbow fitting with a dremel tool so I could  get the finger  

 strainer out. Now I have been looking to get the whole assembly  

 back together. I cannot seem to find a swivel fitting that will  

 allow me to use the original finger strainer (3/8 NPT). I need a  

 1/4 NPT male swivel 90 degree low profile. Or some sort of banjo  

 fitting (already tried the ANDAIR BANJO FITTING FML 1/4"). This is  

 too long. I only have 1.25" from the wing tank to the inside of the  

 first rib. What are the rest of you guys using after the tank have  

 been installed?

 Thanks,

 Kirk



 N198KM

 www.matronics.com/contribution _- 

 ============================================================

- The Matronics Kitfox-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kitfox-List

_________________
Lynn
Kitfox IV-Jabiru 2200
N369LM

Display posts from previous:

	Matronics Email Lists Forum Index -> Kitfox-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum