 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
tonyrenshaw268(at)gmail.c
Guest
|
 Posted: Fri Apr 22, 2011 10:11 am Post subject: Wing pin mod through flap closeout |
 |
|
Gidday,
I am pondering this compulsory task, and would like to know if anyone has used this method over the one through the wing skin? If so, would you do it that way again, and have any specific advice? In blind ignorance, it seems better to me. Thanks.
Reg
Tony Renshaw
Sydney Australia
| | - The Matronics Europa-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Europa-List |
|
|
|
| Back to top |
|
 |
philipgeorge347(at)hotmai
Guest
|
| Posted: Fri Apr 22, 2011 11:11 am Post subject: Wing pin mod through flap closeout |
|
|
Tony i did the wing pin mod thru the close out and infact had the LAA incorperate my method at the back of the instruction sheets having first had Andy Draper come around to inspect it . Saves a whole lot of filling and refinishing ect . No paint is required and no visible signs left . Will be off line for the next three weeks visiting mother in law in Philippines.
regards.
Philip George. G-EORJ mono
| Quote: | Subject: Wing pin mod through flap closeout
From: tonyrenshaw268(at)gmail.com
Date: Sat, 23 Apr 2011 04:07:34 +1000
To: europa-list(at)matronics.com
--> Europa-List message posted by: Tony Renshaw <tonyrenshaw268(at)gmail.com>
Gidday,
I am pondering this compulsory task, and would like to know if anyone has used this method over the one through the wing skin? If so, would you do it that way again, and have any specific advice? In blind ignorance, it seems better to me. Thanks.
Reg
Tony Renshaw
Sydney Australia
&======================== |
| | - The Matronics Europa-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Europa-List |
|
|
|
| Back to top |
|
|
fklein(at)orcasonline.com
Guest
|
| Posted: Fri Apr 22, 2011 11:37 am Post subject: Wing pin mod through flap closeout |
|
|
On Apr 22, 2011, at 11:07 AM, Tony Renshaw wrote:
| Quote: |
>
Gidday,
I am pondering this compulsory task, and would like to know if
anyone has used this method over the one through the wing skin? If
so, would you do it that way again, and have any specific advice? In
blind ignorance, it seems better to me. Thanks.
|
Tony...what do you mean by "this method"?...a ref. to the build manual
instructions might be helpful.
Fred
| | - The Matronics Europa-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Europa-List |
|
|
|
| Back to top |
|
|
neveyre(at)aol.co.uk
Guest
|
| Posted: Fri Apr 22, 2011 12:24 pm Post subject: Wing pin mod through flap closeout |
|
|
Hi Tony,
Go through the closeout, best way by far.
Decide at the same time to do the 1370lb Mod [ if you haven't done that already] as the pin is different, and if you retrofit the 1370 you will have to dig out thepin and nut and redo it ! Tip.... cut out the nyloc ring from the nut, so you can wind it on with a screwdriver pushing on the flats, and only need to crank it the last 1/4 turn with a spanner [ wrench], then ''pot'' it with flox and a couple of plies of Bid before you replace the foam..... saves an awful lot of f*&*$$+**&*
Cheers,
Nev.
--
| | - The Matronics Europa-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Europa-List |
|
|
|
| Back to top |
|
|
kingsnjan(at)westnet.com.
Guest
|
| Posted: Fri Apr 22, 2011 4:23 pm Post subject: Wing pin mod through flap closeout |
|
|
| Quote: | I am pondering this compulsory task,
|
Tony,
The ONLY reason I didn't use the flap closeout method was because I had
minimal clearance between the closeout and the retracted flap and I wasn't
sure it could accommodate the extra thickness.
Cheers
Kingsley
| | - The Matronics Europa-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Europa-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
